Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › from 2021.07
RM38G0E _58 Vehicle Interior _100766 HEATING / AIR CONDITIONING _0467925 AIR CONDITIONING SYSTEM J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  Viscous Heater with Magnet Clutch Circuit  


DESCRIPTION

When the heater switch assembly is pushed, the air conditioning amplifier assembly turns on the viscous heater relay and operates the viscous heater. If the viscous heater does not operate when the heater switch assembly is pushed, there may be a problem in the circuit shown below.

WIRING DIAGRAM

E470766E01
5.458,2.083 5.969,2.292 0.51,0.208 10 false MGCA 5.417,0.885 5.875,1.083 0.458,0.198 10 false SW 1 5,0.74 5.458,0.938 0.458,0.198 10 false 12 5,1.938 5.458,2.135 0.458,0.198 10 false 21 5.24,2.969 6.823,3.469 1.583,0.5 10 false Air Conditioning Amplifier Assembly 2.542,1.354 3,1.552 0.458,0.198 10 false I93 2.542,1.5 4.083,1.75 1.542,0.25 10 false Heater Switch Assembly 3.792,0.885 4.083,1.083 0.292,0.198 10 false +S 4.156,0.885 4.448,1.083 0.292,0.198 10 false 2 3.917,0.438 4.208,0.635 0.292,0.198 10 false E 4.156,0.438 4.448,0.635 0.292,0.198 10 false 5 2.542,0.396 2.938,0.594 0.396,0.198 10 false IND+ 2.333,0.438 2.625,0.635 0.292,0.198 10 false 4 1.49,0.719 2.115,1.083 0.625,0.365 10 false ECU-IGR NO.1 0.042,0.552 1,0.958 0.958,0.406 10 false from IGP NO.1 Relay 0.135,2.604 1.021,3.188 0.885,0.583 10 false from Battery 1.51,2.354 2.594,2.583 1.083,0.229 10 false ECU-IGP NO.3 2.99,2.948 3.865,3.198 0.875,0.25 10 false VISC HTR 3.906,2.083 4.365,2.281 0.458,0.198 10 false 2 3.917,2.5 4.375,2.698 0.458,0.198 10 false 3 2.719,2.083 3.177,2.281 0.458,0.198 10 false 1 2.719,2.5 3.177,2.698 0.458,0.198 10 false 5 2.573,4.063 4.208,4.313 1.635,0.25 10 false Magnet Clutch Assembly 2.521,4.521 4.156,4.771 1.635,0.25 10 false I49 2.531,4.656 4.25,5.073 1.719,0.417 10 false Viscous with Magnet Clutch Heater Assembly 3.792,3.552 4.25,3.75 0.458,0.198 10 false MG+ 4.208,3.542 4.667,3.74 0.458,0.198 10 false 1 5,1 5.458,1.198 0.458,0.198 10 false I33 4.99,2.208 5.448,2.406 0.458,0.198 10 false I32 1.667,2.802 2.542,3.052 0.875,0.25 10 false VISC HTR

CAUTION / NOTICE / HINT

NOTICE:

When the servo motor or air conditioning amplifier assembly is replaced, be sure to perform servo motor initialization.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>INITIALIZATION


HINT:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (HEATER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the I93 heater switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I93)Location & Routing

Click Connector(I93)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Heater Switch Assembly

I93-5 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I93)Location & Routing

Click Connector(I93)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Heater Switch Assembly

I93-4 (IND+) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.INSPECT HEATER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT HEATER SWITCH ASSEMBLY

OK

3.INSPECT VISCOUS HEATER RELAY (VISC HTR)

NG

3.INSPECT VISCOUS HEATER RELAY (VISC HTR)
a.

Remove the viscous heater relay (VISC HTR) from the No. 4 engine room relay block.


b.

Inspect the viscous heater relay (VISC HTR).

Click hereVehicle Interior>HEATING / AIR CONDITIONING>RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

4.INSPECT VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY

NG

REPLACE VISCOUS HEATER RELAY (VISC HTR)

4.INSPECT VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY

OK

5.CHECK HARNESS AND CONNECTOR (HEATER SWITCH ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPLACE VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (HEATER SWITCH ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the I93 heater switch assembly connector.


b.

Disconnect the I33 air conditioning amplifier assembly connector.



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (VISCOUS HEATER RELAY - VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY AND AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (VISCOUS HEATER RELAY - VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY AND AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Remove the viscous heater relay (VISC HTR) from the No. 4 engine room relay block.


b.

Disconnect the I49 viscous with magnet clutch heater assembly connector.


c.

Disconnect the I32 air conditioning amplifier assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I49,I32)Location & Routing

Click Connector(I49)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Steering Lock Actuator or Upper Bracket Assembly

Click Connector(I32)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Air Conditioning Amplifier Assembly

Relay terminal 3 - I49-1 (MG+) Always Below 1 Ω
Relay terminal 2 - I32-21 (MGCA) Always Below 1 Ω
Relay terminal 3 or I49-1 (MG+) - Other terminals and body ground Always 10 kΩ or higher
Relay terminal 2 or I32-21 (MGCA) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (VISCOUS HEATER RELAY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (VISCOUS HEATER RELAY - BATTERY)
a.

Remove the viscous heater relay (VISC HTR) from the No. 4 engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Relay terminal 1 - Body ground Ignition switch ON 11 to 14 V
Relay terminal 1 - Body ground Ignition switch off Below 1 V
Relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BATTERY)
a.

Disconnect the I32 air conditioning amplifier assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I32)Location & Routing

Click Connector(I32)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Air Conditioning Amplifier Assembly

I32-21 (MGCA) - Body ground Ignition switch off Below 1 V
I32-21 (MGCA) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR