Home › Drivetrain › AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for F33A-FTV) › from 2021.07
RM38G0E _52 Drivetrain _100435 AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE _0488019 AUTOMATIC TRANSMISSION SYSTEM(for F33A-FTV) C

AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for F33A-FTV)  P071015  Transmission Fluid Temperature Sensor "A" Circuit Short to Battery or Open  


DESCRIPTION

The No. 1 ATF temperature sensor converts the fluid temperature into a resistance value for use by the TCM.

The TCM applies a voltage to the temperature sensor through terminal THO1 of the TCM.

The sensor resistance changes with the No. 1 ATF temperature. As the temperature becomes higher, the sensor resistance decreases.

One terminal of the sensor is grounded so that the sensor resistance and voltage goes down as the temperature becomes higher.

The TCM calculates the fluid temperature based on the voltage signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P071015 Transmission Fluid Temperature Sensor "A" Circuit Short to Battery or Open No. 1 ATF temperature sensor voltage is higher than 4.915 V for 0.5 seconds or more and either condition is met (1-trip detection logic):
·

10 seconds or more have elapsed after the engine start when the engine coolant temperature and intake air temperature are higher than -29.375°C (-20.875°F).

·

15 minutes or more have elapsed after the engine start when the engine coolant temperature and intake air temperature are -29.375°C (-20.875°F) or less.


·

Open or short in ATF temperature sensor circuit

·

Transmission wire (No. 1 ATF temperature sensor)

·

TCM


Comes on DTC stored SAE: P0713

DTC Detection Condition Patterns
Vehicle Condition
Pattern 1 Pattern 2
Diagnostic Condition 10 seconds or more have elapsed after the engine start when the engine coolant temperature and intake air temperature are higher than -29.375°C (-20.875°F). ○ -
15 minutes or more have elapsed after the engine start when the engine coolant temperature and intake air temperature are -29.375°C (-20.875°F) or less. - ○
Malfunction Condition No. 1 ATF temperature sensor voltage is higher than 4.915 V. ○ ○
Duration 0.5 seconds or more 0.5 seconds or more
Detection Logic 1-trip detection logic 1-trip detection logic

HINT:

This DTC is stored when either of the above detection patterns is met.


MONITOR DESCRIPTION

This DTC indicates an open or short in the No. 1 ATF temperature sensor circuit. The No. 1 ATF temperature sensor converts the ATF temperature into an electrical resistance value. Based on the resistance, the TCM determines the ATF temperature, and can detect an open or short in the No. 1 ATF temperature sensor circuit. If the resistance value of the No. 1 ATF temperature sensor is higher than 156 kΩ*, the TCM interprets this as a malfunction of the No. 1 ATF temperature sensor or in the wire harness, illuminates the MIL and stores this DTC.

*: -40°C (-40°F) is indicated regardless of the actual ATF temperature.

HINT:

The ATF temperature can be checked in the Data List.


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for at least 30 seconds.

3.

Start the engine and wait for 15 minutes or more.

4.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

5.

Input the DTC: P071015.

6.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for F33A-FTV)>PRECAUTION


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Read the Data List according to the display on the GTS.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Temperature No.1 ATF temperature sensor value Min.: -40°C (-40°F)
Max.: 150°C (302°F)
·

Approximately 80°C (176°F): After stall speed test

·

Equal to ambient temperature: While engine is cold


If value is -40°C (-40°F) or 150°C (302°F), ATF temperature sensor circuit is open or shorted
Powertrain > Transmission > Data List
Tester Display
A/T Oil Temperature No.1
50003 373 180
HINT:
·

When DTC P071011 is output and the GTS shows 150°C (302°F) or higher, there is a short circuit.

·

When DTC P071015 is output and the GTS shows -40°C (-40°F), there is an open circuit.

Check the temperature displayed on the GTS in order to check if a malfunction exists.

Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
150°C (302°F) or higher Short circuit

·

If a circuit related to the ATF temperature sensor becomes open, P071015 will be stored in approximately 0.5 seconds. It is not necessary to inspect the circuit when P071000 is output.





PROCEDURE

1.READ VALUE USING GTS (A/T OIL TEMPERATURE NO. 1)
a.

Warm up the engine.


b.

Read the Data List according to the display on the GTS.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Temperature No.1 ATF temperature sensor value Min.: -40°C (-40°F)
Max.: 150°C (302°F)
·

Approximately 80°C (176°F): After stall speed test

·

Equal to ambient temperature: While engine is cold


If value is -40°C (-40°F) or 150°C (302°F), ATF temperature sensor circuit is open or shorted
Powertrain > Transmission > Data List
Tester Display
A/T Oil Temperature No.1
50003 373 180

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

3.REPLACE TCM

B

2.CHECK HARNESS AND CONNECTOR (NO. 1 ATF TEMPERATURE SENSOR - TCM)
2.CHECK HARNESS AND CONNECTOR (NO. 1 ATF TEMPERATURE SENSOR - TCM)
a.

Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C36)Location & Routing

Click Connector(C36)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Transmission Control ECU Assembly

C36-52 (THO1) - C36-53 (E2) Always 79 Ω to 156 kΩ
C36-52 (THO1) - Other terminals Always 10 kΩ or higher
C36-53 (E2) - Other terminals Always 10 kΩ or higher


HINT:

If the resistance is out of the specified range at any of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.

ATF Temperature Specified Condition
10°C (50°F) 5 to 8 kΩ
25°C (77°F) 2.5 to 4.5 kΩ
110°C (230°F) 0.22 to 0.28 kΩ



Result:
Proceed to
OK
NG



OK

3.REPLACE TCM

NG

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
4.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.

Disconnect the transmission wire connector.


b.

Disconnect the TCM connector.



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE TRANSMISSION WIRE (NO. 1 ATF TEMPERATURE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR