Home › Drivetrain › AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for F33A-FTV) › from 2021.07
RM38G0E _52 Drivetrain _100435 AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE _0488019 AUTOMATIC TRANSMISSION SYSTEM(for F33A-FTV) C

AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for F33A-FTV)  P071512  Input/Turbine Speed Sensor "A" Circuit Short to Battery  P071514  Input/Turbine Speed Sensor "A" Circuit Short to Ground or Open  P071531  Input/Turbine Speed Sensor "A" No Signal  


DESCRIPTION

The transmission revolution sensor (NT) detects the input shaft rotation speed and sends it to the TCM.

Based on the transmission revolution sensor (NT) signal and the transmission revolution sensor (SP2) signals, the TCM controls engine torque and shift timing. Based on the input shaft rotation speed and the engine speed signal, lock-up control is performed.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P071512 Input/Turbine Speed Sensor "A" Circuit Short to Battery When the ignition switch is ON, the transmission revolution sensor (NT) input voltage is higher than 1.9 V for 4.5 seconds or more (1-trip detection logic).
·

Harness and connector

·

Transmission wire

·

Transmission revolution sensor (NT)

·

TCM


Comes on DTC stored SAE: P07C0
P071514 Input/Turbine Speed Sensor "A" Circuit Short to Ground or Open When the ignition switch is ON, the transmission revolution sensor (NT) input voltage is below 0.1 V for 4.5 seconds or more (1-trip detection logic).
·

Harness and connector

·

Transmission wire

·

Transmission revolution sensor (NT)

·

TCM


Comes on DTC stored SAE: P07BF
P071531 Input/Turbine Speed Sensor "A" No Signal All conditions are met for 5 seconds or more (1-trip detection logic):
·

Transmission revolution sensor (SP2) value is 27 km/h (16.78 mph) or more.

·

Vehicle speed is 27 km/h (16.78 mph) or more.

·

Shift lever is in D.

·

Transmission revolution sensor (NT) value is less than 300 rpm.


·

Harness and connector

·

Transmission wire

·

Transmission revolution sensor (NT)

·

TCM


Comes on DTC stored SAE: P0717

MONITOR DESCRIPTION

The NT terminal of the TCM detects a pulse signal from the transmission revolution sensor (NT) (input RPM). The TCM calculates gear shifts comparing the transmission revolution sensor (NT) with the transmission revolution sensor (SP2).

While the vehicle is being driven with the shift lever in D, if the input shaft revolution (speed) is less than 300 rpm*1 when the output shaft speed is 27 km/h (16.78 mph) or more, the TCM interprets this as a malfunction, illuminates the MIL and stores a DTC.

*: Pulse is not output or is irregularly output.

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for at least 30 seconds.

3.
4.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

5.

Input the DTC: P071512, P071514 or P071531.

6.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C364249E13
2.76,1.146 3.375,1.344 0.615,0.198 10 false NTB 5.146,1.146 5.76,1.344 0.615,0.198 10 false NTB 5.156,2.271 5.771,2.469 0.615,0.198 10 false NTO 2.76,2.271 3.375,2.469 0.615,0.198 10 false NTO 4.854,1.146 5.26,1.344 0.406,0.198 10 false 30 4.844,2.281 5.229,2.479 0.385,0.198 10 false 11 3.146,1.146 3.458,1.344 0.313,0.198 10 false 21 3.135,2.271 3.448,2.469 0.313,0.198 10 false 22 1.042,1.75 2.583,2.188 1.542,0.438 10 false Transmission Revolution Sensor (NT) 0.594,2.229 0.75,2.427 0.156,0.198 10 false 1 0.604,1.406 0.76,1.604 0.156,0.198 10 false 2 0.979,2.906 1.438,3.104 0.458,0.198 10 false C33 0.99,3.073 2.823,3.271 1.833,0.198 10 false Transmission Wire 5.427,3.177 5.771,3.344 0.344,0.167 10 false C36 5.438,3.344 7.115,3.563 1.677,0.219 10 false TCM 5.76,0.99 6.167,1.156 0.406,0.167 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for F33A-FTV)>PRECAUTION


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Read the Data List according to the display on the GTS.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
NT Sensor Speed Input shaft speed Min.: 0 rpm
Max.: 12750 rpm
·

Equal to engine speed: Lock-up on (after warming up engine)

·

Nearly equal to engine speed: Lock-up off (idling with shift lever in N)


Data is displayed in increments of 50 rpm
Powertrain > Transmission > Data List
Tester Display
NT Sensor Speed
50003 373 174
HINT:
·

NT Sensor Speed is always 0 while driving: Open or short in the sensor or circuit.

·

NT Sensor Speed is always more than 0 and less than 300 rpm while driving the vehicle at 27 km/h (16.78 mph) or more: Sensor malfunction, improper installation, or intermittent connection malfunction in the circuit.





PROCEDURE

1.READ VALUE USING GTS (NT SENSOR SPEED AND NT SENSOR VOLTAGE)
a.

Read the Data List according to the display on the GTS.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
NT Sensor Speed Input shaft speed Min.: 0 rpm
Max.: 12750 rpm
·

Equal to engine speed: Lock-up on (after warming up engine)

·

Nearly equal to engine speed: Lock-up off (idling with shift lever in N)


Data is displayed in increments of 50 rpm
NT Sensor Voltage NT sensor voltage Min.: 0.000 V
Max.: 4.999 V
0.1 to 1.9 V: Idling -
Powertrain > Transmission > Data List
Tester Display
NT Sensor Speed
NT Sensor Voltage
50003 373 174,175

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

5.REPLACE TCM

B

2.CHECK TRANSMISSION REVOLUTION SENSOR TERMINAL (NT TERMINAL)
2.CHECK TRANSMISSION REVOLUTION SENSOR TERMINAL (NT TERMINAL)
a.

Disconnect the transmission wire connector.



c.

Turn the ignition switch to ON.



Result:
Proceed to
OK
NG



OK

3.INSPECT TRANSMISSION WIRE (TRANSMISSION REVOLUTION SENSOR (NT))

NG

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
3.INSPECT TRANSMISSION WIRE (TRANSMISSION REVOLUTION SENSOR (NT))
a.
C377609C10
0.104,2.208 0.5,2.51 0.396,0.302 2.563,3 2.208,2.531 true 1.813,3.01 2.094,2.531 true 2.25,1.344 1.896,0.875 true 1.385,1.344 1.667,0.865 true 0.104,0.26 0.417,0.458 0.313,0.198 10 false *a 0.104,1.823 0.417,2.021 0.313,0.198 10 false *b 2.448,3.063 2.906,3.26 0.458,0.198 10 false NTB 1.667,3.063 2.125,3.26 0.458,0.198 10 false NTO 2.25,1.406 2.708,1.604 0.458,0.198 10 false 1 1.323,1.406 1.781,1.604 0.458,0.198 10 false 2 0.198,2.292 0.51,2.49 0.313,0.198 10 false C33
*a Front view of wire harness connector
(to Transmission Revolution Sensor (NT))
*b Component without harness connected
(Transmission Wire)


Disconnect the transmission revolution sensor (NT) connector.

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>SPEED SENSOR>REMOVAL


b.

Disconnect the transmission wire connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C33)Location & Routing

Click Connector(C33)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Automatic Transmission Assembly (Transmission Wire)

Terminal 2 of the transmission revolution sensor (NT) connector - C33-21 (NTB) Always Below 1 Ω
Terminal 1 of the transmission revolution sensor (NT) connector - C33-22 (NTO) Always Below 1 Ω
Terminal 2 of the transmission revolution sensor (NT) connector or C33-21 (NTB) - Body ground Always 10 kΩ or higher
Terminal 1 of the transmission revolution sensor (NT) connector or C33-22 (NTO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TRANSMISSION REVOLUTION SENSOR (NT)

NG

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.

Disconnect the transmission wire connector.


b.

Disconnect the TCM connector.



Result:
Proceed to
OK
NG



OK

5.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR