Home › Drivetrain › AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for F33A-FTV) › from 2021.07
RM38G0E _52 Drivetrain _100435 AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE _0488019 AUTOMATIC TRANSMISSION SYSTEM(for F33A-FTV) C

AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for F33A-FTV)  P072012  Output Speed Sensor Circuit Short to Battery  P072014  Output Speed Sensor Circuit Short to Ground or Open  P072031  Output Speed Sensor No Signal  


DESCRIPTION

The transmission revolution sensor (SP2) detects the output shaft rotation speed and sends it to the TCM.

Based on the transmission revolution sensor (NT) signal and the transmission revolution sensor (SP2) signal, the TCM controls engine torque and shift timing.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P072012 Output Speed Sensor Circuit Short to Battery When the ignition switch is ON, the transmission revolution sensor (SP2) input voltage is higher than 1.8 V for 4.5 seconds or more (1-trip detection logic).
·

Harness and connector

·

Transmission wire

·

Transmission revolution sensor (SP2)

·

TCM


Comes on DTC stored SAE: P077D
P072014 Output Speed Sensor Circuit Short to Ground or Open When the ignition switch is ON, the transmission revolution sensor (SP2) input voltage is below 0.2 V for 4.5 seconds or more (1-trip detection logic).
·

Harness and connector

·

Transmission wire

·

Transmission revolution sensor (SP2)

·

TCM


Comes on DTC stored SAE: P077C
P072031 Output Speed Sensor No Signal All conditions are met for 5 seconds or more (1-trip detection logic):
·

Transmission revolution sensor (NT) value is 1500 rpm or more.

·

Vehicle speed is 10 km/h (6.22 mph) or more.

·

Shift lever is in D.

·

SP2 signal is not input.


·

Harness and connector

·

Transmission wire

·

Transmission revolution sensor (SP2)

·

TCM


Comes on DTC stored SAE: P0722

MONITOR DESCRIPTION

The transmission revolution sensor (SP2) monitors the output shaft speed.

The TCM controls the gearshift point and the lock up timing based on the signals from the transmission revolution sensor (SP2) and throttle position sensor.

If the TCM detects no signal from the transmission revolution sensor (SP2) even while the vehicle is moving, it will determine the transmission revolution sensor (SP2) is malfunctioning, illuminate the MIL and store a DTC.

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for at least 30 seconds.

3.
4.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

5.

Input the DTC: P072012, P072014 or P072031.

6.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C364249E14
1.271,3.115 3.875,3.313 2.604,0.198 10 false Transmission Wire 1.031,1.708 2.531,2.146 1.5,0.438 10 false Transmission Revolution Sensor (SP2) 5.156,1.156 5.615,1.354 0.458,0.198 10 false SP2B 5.156,2.281 5.615,2.479 0.458,0.198 10 false SP2O 2.646,2.281 3.104,2.479 0.458,0.198 10 false SP2O 2.646,1.156 3.104,1.354 0.458,0.198 10 false SP2B 4.854,1.146 5.313,1.344 0.458,0.198 10 false 12 3.146,1.146 3.604,1.344 0.458,0.198 10 false 29 3.146,2.281 3.604,2.479 0.458,0.198 10 false 30 4.854,2.281 5.313,2.479 0.458,0.198 10 false 31 0.552,1.396 1.01,1.594 0.458,0.198 10 false 2 0.573,2.229 1.031,2.427 0.458,0.198 10 false 1 1.25,2.938 1.708,3.135 0.458,0.198 10 false C33 5.49,3.229 5.948,3.427 0.458,0.198 10 false C36 5.5,3.406 5.958,3.604 0.458,0.198 10 false TCM 5.75,0.99 6.208,1.188 0.458,0.198 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for F33A-FTV)>PRECAUTION


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Read the Data List according to the display on the GTS.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Speed (SP2) Output shaft speed Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
0 km/h (0 mph): Vehicle stopped
(Output shaft speed is equal to vehicle speed)
-
Powertrain > Transmission > Data List
Tester Display
Speed (SP2)
50003 373 362
HINT:
·

Speed (SP2) is always 0 while driving: Open or short in the sensor or circuit.

·

The Speed (SP2) value displayed on the GTS is much lower than the actual vehicle speed: Sensor malfunction, improper installation, or intermittent connection malfunction of the circuit.





PROCEDURE

1.READ VALUE USING GTS (SPEED (SP2) AND SP2 SENSOR VOLTAGE)
a.

Read the Data List according to the display on the GTS.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Speed (SP2) Output shaft speed Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
0 km/h (0 mph): Vehicle stopped
(Output shaft speed is equal to vehicle speed)
-
SP2 Sensor Voltage SP2 sensor voltage Min.: 0.000 V
Max.: 4.999 V
0.2 to 1.8 V: Idling -
Powertrain > Transmission > Data List
Tester Display
Speed (SP2)
SP2 Sensor Voltage
50003 373 362,391

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

5.REPLACE TCM

B

2.CHECK TRANSMISSION REVOLUTION SENSOR TERMINAL (SP2 TERMINAL)
2.CHECK TRANSMISSION REVOLUTION SENSOR TERMINAL (SP2 TERMINAL)
a.

Disconnect the transmission wire connector.



c.

Turn the ignition switch to ON.



Result:
Proceed to
OK
NG



OK

3.INSPECT TRANSMISSION WIRE (TRANSMISSION REVOLUTION SENSOR (SP2))

NG

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
3.INSPECT TRANSMISSION WIRE (TRANSMISSION REVOLUTION SENSOR (SP2))
a.
C377609C09
0.094,2.219 0.5,2.479 0.406,0.26 1.667,3 1.313,2.531 true 0.906,3.01 1.188,2.531 true 2.25,1.344 1.896,0.875 true 1.385,1.344 1.667,0.865 true 0.104,0.26 0.417,0.458 0.313,0.198 10 false *a 0.104,1.823 0.417,2.021 0.313,0.198 10 false *b 1.563,3.042 2.021,3.24 0.458,0.198 10 false SP2B 0.75,3.042 1.208,3.24 0.458,0.198 10 false SP2O 2.25,1.406 2.708,1.604 0.458,0.198 10 false 1 1.323,1.406 1.781,1.604 0.458,0.198 10 false 2 0.188,2.292 0.5,2.49 0.313,0.198 10 false C33
*a Front view of wire harness connector
(to Transmission Revolution Sensor (SP2))
*b Component without harness connected
(Transmission Wire)


Disconnect the transmission revolution sensor (SP2) connector.

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>SPEED SENSOR>REMOVAL


b.

Disconnect the transmission wire connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C33)Location & Routing

Click Connector(C33)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Automatic Transmission Assembly (Transmission Wire)

Terminal 2 of the transmission revolution sensor (SP2) connector - C33-29 (SP2B) Always Below 1 Ω
Terminal 1 of the transmission revolution sensor (SP2) connector - C33-30 (SP2O) Always Below 1 Ω
Terminal 2 of the transmission revolution sensor (SP2) connector or C33-29 (SP2B) - Body ground Always 10 kΩ or higher
Terminal 1 of the transmission revolution sensor (SP2) connector or C33-30 (SP2O) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TRANSMISSION REVOLUTION SENSOR (SP2)

NG

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.

Disconnect the transmission wire connector.


b.

Disconnect the TCM connector.



Result:
Proceed to
OK
NG



OK

5.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR