Home › Drivetrain › AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for F33A-FTV) › from 2021.07
RM38G0E _52 Drivetrain _100435 AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE _0488019 AUTOMATIC TRANSMISSION SYSTEM(for F33A-FTV) C

AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for F33A-FTV)  P077011  Shift Solenoid "E" Circuit Short to Ground  


DESCRIPTION

Based on the ON-OFF combinations of the solenoid (SL1, SL2, SL3, SL4, SL5, SL6, SC1 and SR) valves, the TCM performs gear shifts from 1st gear to 10th gear.

If a circuit related to a solenoid valve is open or shorted, the TCM uses the fail-safe function to turn other solenoid valves ON or OFF. If an open or short has occurred, the TCM cuts power to the malfunctioning solenoid valve.

HINT:

The following table shows normal operation of the solenoid (SR) valve.

Solenoid Valve Operation:
Shift Lever Solenoid (SR) Valve
P ON
R OFF
N ON
D ON


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P077011 Shift Solenoid "E" Circuit Short to Ground The solenoid (SR) valve terminal voltage level is low, when the solenoid (SR) valve is operated (1-trip detection logic).
·

Harness and connector

·

Transmission wire

·

Solenoid (SR) valve

·

TCM


Comes on DTC stored SAE: P0985

MONITOR DESCRIPTION

This DTC indicates a short in the solenoid (SR) valve circuit. When there is an open or short in any solenoid valve circuit, the TCM detects the problem, illuminates the MIL and stores a DTC.

When the solenoid (SR) valve is on, if its resistance is 8 Ω or less, the TCM determines there is a short in the solenoid (SR) valve circuit.

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for at least 30 seconds.

3.

Wait for 3 seconds or more with the shift lever in P.

4.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

5.

Input the DTC: P077011.

6.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C378295E31
5.188,1.125 5.646,1.323 0.458,0.198 10 false SR 4.917,1.125 5.375,1.323 0.458,0.198 10 false 45 3.635,1.125 4.094,1.323 0.458,0.198 10 false 6 3.271,1.125 3.729,1.323 0.458,0.198 10 false SR 1.479,1.74 4.542,1.938 3.063,0.198 10 false Solenoid (SR) Valve 1.698,2.698 4.76,2.896 3.063,0.198 10 false C33 1.708,2.875 4.771,3.073 3.063,0.198 10 false Transmission Wire 5.615,2.948 6,3.135 0.385,0.188 10 false C36 5.625,3.135 6.167,3.323 0.542,0.188 10 false TCM 5.792,0.865 6.25,1.063 0.458,0.198 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for F33A-FTV)>PRECAUTION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE (SOLENOID (SR) VALVE) - TCM)
a.

Disconnect the TCM connector.



Result:
Proceed to
OK
NG



OK

2.REPLACE TCM

NG

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

OK

4.INSPECT SOLENOID (SR) VALVE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT SOLENOID (SR) VALVE
a.
C375005C02
0.052,0.052 0.365,0.25 0.313,0.198 10 false *1
*1 Solenoid (SR) Valve


Remove the solenoid (SR) valve.

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal of solenoid (SR) valve connector - Solenoid (SR) valve body 20°C (68°F) 11 to 15 Ω



c.

Connect a positive (+) lead from the battery to the terminal of the solenoid valve connector, and a negative (-) lead to the solenoid body. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

NG