Home › Drivetrain › AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for F33A-FTV) › from 2021.07
RM38G0E _52 Drivetrain _100435 AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE _0488019 AUTOMATIC TRANSMISSION SYSTEM(for F33A-FTV) C

AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for F33A-FTV)  P170000  Unified IC Malfunction  


DESCRIPTION

When the TCM internal unified IC (power generation, linear solenoid drive) determines that there is a malfunction, the MIL illuminates and a DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P170000 Unified IC Malfunction TCM internal unified IC malfunction TCM Comes on DTC stored SAE: P1700

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off.

3.

Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

4.

Connect the cable to the negative (-) battery terminal.

5.

Turn the ignition switch to ON and wait for 10 seconds or more.

6.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

7.

Input the DTC: P170000.

8.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.




CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for F33A-FTV)>PRECAUTION

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Transmission > Clear DTCs
50002 373

Result:
Proceed to
NEXT



NEXT

2.CHECK DTC OUTPUT (DTC P170000)
2.CHECK DTC OUTPUT (DTC P170000)
a.

Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON and wait for 1 minute or more.


d.

Read the DTCs using the GTS.

Powertrain > Transmission > Trouble Codes
50001 373

Result:
Result Proceed to
DTC P170000 is output A
DTCs other than P170000 are also output B
DTCs are not output C



A

3.REPLACE TCM

B

GO TO DTC CHART

C