Home › Drivetrain › AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for F33A-FTV) › from 2021.07
RM38G0E _52 Drivetrain _100435 AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE _0488019 AUTOMATIC TRANSMISSION SYSTEM(for F33A-FTV) C

AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for F33A-FTV)  P274011  Transmission Fluid Temperature Sensor "B" Circuit Short to Ground  


DESCRIPTION

The No. 2 ATF temperature sensor converts the fluid temperature into a resistance value for use by the TCM.

The TCM applies a voltage to the temperature sensor through terminal THOC of the TCM.

The sensor resistance changes with the No. 2 ATF temperature. As the temperature becomes higher, the sensor resistance decreases.

One terminal of the sensor is grounded so that the sensor resistance and voltage goes down as the temperature becomes higher.

The TCM calculates the fluid temperature based on the voltage signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P274011 Transmission Fluid Temperature Sensor "B" Circuit Short to Ground When the ignition switch is ON, the No. 2 ATF temperature sensor voltage is below 0.0459 V for 0.5 seconds or more (1-trip detection logic).
·

Short in No. 2 ATF temperature sensor circuit

·

Transmission wire (No. 2 ATF temperature sensor)

·

TCM


Does not come on DTC stored SAE: P2742

MONITOR DESCRIPTION

This DTC indicates a short in the NO. 2 ATF temperature sensor circuit. The NO. 2 ATF temperature sensor converts the ATF temperature into an electrical resistance value. Based on the resistance, the TCM determines the ATF temperature, and can detect a short in the NO. 2 ATF temperature sensor circuit. If the resistance value of the NO. 2 ATF temperature sensor is below 25 Ω*, the TCM interprets this as a malfunction of the NO. 2 ATF temperature sensor or in the wire harness, illuminates the MIL and stores this DTC.

*: 150°C (302°F) or higher is indicated regardless of the actual ATF temperature.

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for at least 30 seconds.

3.

Wait for 3 seconds or more with the ignition switch ON.

4.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

5.

Input the DTC: P274011.

6.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C311451E83
1.563,2.865 3.135,3.052 1.573,0.188 10 false Transmission Wire 1.563,2.688 2.021,2.885 0.458,0.198 10 false C33 5.552,2.958 6.01,3.156 0.458,0.198 10 false C36 5.552,3.125 6.479,3.5 0.927,0.375 10 false TCM 4.906,1.146 5.365,1.344 0.458,0.198 10 false 54 4.917,2.115 5.375,2.313 0.458,0.198 10 false 55 5.198,1.146 5.656,1.344 0.458,0.198 10 false THOC 5.198,2.115 5.656,2.313 0.458,0.198 10 false ETH2 5.938,0.979 6.396,1.177 0.458,0.198 10 false 5 V 3.948,1.125 4.406,1.323 0.458,0.198 10 false 3 3.938,2.094 4.396,2.292 0.458,0.198 10 false 4 3.427,1.125 3.885,1.323 0.458,0.198 10 false OT2+ 3.427,2.094 3.885,2.292 0.458,0.198 10 false OT2- 1.51,1.719 3.552,2.188 2.042,0.469 10 false No. 2 ATF Temperature Sensor

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for F33A-FTV)>PRECAUTION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NO. 2 ATF TEMPERATURE SENSOR - TCM)
a.

Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C36)Location & Routing

Click Connector(C36)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Transmission Control ECU Assembly

C36-54 (THOC) - C36-55 (ETH2) Always 25 Ω to 156 kΩ
C36-54 (THOC) - Body ground and other terminals Always 10 kΩ or higher
C36-55 (ETH2) - Body ground and other terminals Always 10 kΩ or higher


HINT:

If the resistance is out of the specified range at any of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.

ATF Temperature Specified Condition
10°C (50°F) 5 to 8 kΩ
25°C (77°F) 2.5 to 4.5 kΩ
110°C (230°F) 0.22 to 0.28 kΩ



Result:
Proceed to
OK
NG



OK

2.REPLACE TCM

NG

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.

Disconnect the transmission wire connector.


b.

Disconnect the TCM connector.



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE TRANSMISSION WIRE (NO. 2 ATF TEMPERATURE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR