The TCM controls the lock-up solenoid using a predetermined current, and performs lock-up and flex lock-up control.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P275614 | Torque Converter Clutch Pressure Control Solenoid Control Circuit Short to Ground or Open | Solenoid (SLU) valve circuit current is lower than specified value for the target current continuously for 1 second or more while driving (1-trip detection logic). |
·
Harness and connector
·
Transmission wire
·
Solenoid (SLU) valve
·
TCM |
Comes on | DTC stored | SAE: P2764 |
When an open or short in a solenoid (SLU) valve circuit is detected, the TCM will determine that there is a malfunction, illuminate the MIL and store this DTC.
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Perform the Lock-up Function in Road Test.
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
Input the DTC: P275614.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL |
·
DTC judgment completed
·
System normal |
| ABNORMAL |
·
DTC judgment completed
·
System abnormal |
| INCOMPLETE |
·
DTC judgment not completed
·
Perform driving pattern after confirming DTC enabling conditions |
| N/A |
·
Unable to perform DTC judgment
·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Refer to DTC P275612.
Perform registration and/or initialization when parts related to the automatic transmission are replaced.
Disconnect the TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C36)Location & Routingewd_type=routing;type=c;code=C36 |
||
| C36-4 (SLU+) - C36-23 (SLU-) | 20°C (68°F) | 5.0 to 5.6 Ω |
| C36-4 (SLU+) or C36-23 (SLU-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
NEXT
Disconnect the transmission wire connector.
Disconnect the TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C33,C36)Location & Routingewd_type=routing;type=c,c;code=C33,C36 |
||
| C33-17 (SLU+) - C36-4 (SLU+) | Always | Below 1 Ω |
| C33-18 (SLU-) - C36-23 (SLU-) | Always | Below 1 Ω |
| C33-17 (SLU+) or C36-4 (SLU+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C33-18 (SLU-) or C36-23 (SLU-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Solenoid (SLU) Valve |
Remove the solenoid (SLU) valve.
Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.
Valve moves and makes operating sound.
| Proceed to |
|---|
| OK |
| NG |
OK
NG