Home › Drivetrain › AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for F33A-FTV) › from 2021.07
RM38G0E _52 Drivetrain _100435 AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE _0488019 AUTOMATIC TRANSMISSION SYSTEM(for F33A-FTV) C

AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for F33A-FTV)  P280712  Pressure Control Solenoid "G" Circuit Short to Battery  


DESCRIPTION

Based on the ON-OFF combinations of the solenoid (SL1, SL2, SL3, SL4, SL5, SL6, SC1 and SR) valves, the TCM performs gear shifts from 1st gear to 10th gear.

If a circuit related to a solenoid valve is open or shorted, the TCM uses the fail-safe function to turn other solenoid valves ON or OFF. If an open or short has occurred, the TCM cuts power to the malfunctioning solenoid valve.

HINT:

The following table shows normal operation of the solenoid (SL4) valve when the shift lever is in D.

Solenoid Valve Operation:
Gear Solenoid (SL4) Valve
1st OFF
2nd OFF
3rd OFF
4th ON
5th ON
6th ON
7th ON
8th ON
9th OFF
10th OFF


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P280712 Pressure Control Solenoid "G" Circuit Short to Battery Solenoid (SL4) valve circuit current is higher than specified value for the target current continuously for 1 second or more while driving with gear changes (1-trip detection logic).
·

Harness and connector

·

Transmission wire

·

Solenoid (SL4) valve

·

TCM


Comes on DTC stored SAE: P2815

MONITOR DESCRIPTION

This DTC indicates a short in the solenoid (SL4) valve circuit. The TCM commands gear shifts by turning the solenoid valves on or off. When there is an open or short in any solenoid valve circuit, the TCM detects the problem, illuminates the MIL and stores a DTC.

The TCM performs the fail-safe function and turns the other normal solenoid valves on or off. In case of an open or short circuit, the TCM stops sending current to the open or shorted solenoid.

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for at least 30 seconds.

3.
4.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

5.

Input the DTC: P280712.

6.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C378274E31
1.771,2.875 4.375,3.073 2.604,0.198 10 false Transmission Wire 1.49,1.75 4.552,1.948 3.063,0.198 10 false Solenoid (SL4) Valve 5.615,3.229 6.073,3.427 0.458,0.198 10 false TCM 5.604,3.063 6.063,3.26 0.458,0.198 10 false C36 1.76,2.698 2.219,2.896 0.458,0.198 10 false C33 5.188,1.135 5.823,1.354 0.635,0.219 10 false SL4+ 3.479,1.125 4.115,1.344 0.635,0.219 10 false SL4+ 3.5,2.094 4.135,2.313 0.635,0.219 10 false SL4- 5.188,2.104 5.823,2.323 0.635,0.219 10 false SL4- 4.979,1.125 5.271,1.354 0.292,0.229 10 false 8 4.906,2.104 5.198,2.333 0.292,0.229 10 false 27 3.917,1.125 4.208,1.354 0.292,0.229 10 false 15 3.927,2.094 4.219,2.323 0.292,0.229 10 false 16 1.01,1.313 1.302,1.542 0.292,0.229 10 false 1 1.021,2.156 1.313,2.385 0.292,0.229 10 false 2 5.813,0.792 6.344,1.021 0.531,0.229 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for F33A-FTV)>PRECAUTION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE (SOLENOID (SL4) VALVE) - TCM)
a.

Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C36)Location & Routing

Click Connector(C36)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Transmission Control ECU Assembly

C36-8 (SL4+) - C36-27 (SL4-) 20°C (68°F) 5.0 to 5.6 Ω
C36-8 (SL4+) or C36-27 (SL4-) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REPLACE TCM

NG

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

OK

4.INSPECT SOLENOID (SL4) VALVE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT SOLENOID (SL4) VALVE
a.
C197715C19
1.76,0.969 2.208,0.385 false 1.479,0.958 1.021,0.375 false 1.771,2.958 2.219,2.365 false 1.469,2.948 1.01,2.354 false 0.094,0.083 0.531,0.417 0.438,0.333 10 *1 2.26,0.26 2.427,0.458 0.167,0.198 10 1 0.875,0.24 1.042,0.438 0.167,0.198 10 2 2.271,2.24 2.438,2.438 0.167,0.198 10 1 0.906,2.24 1.073,2.438 0.167,0.198 10 2 1.927,3.927 2.208,4.125 0.281,0.198 10 (+) 1.146,3.938 1.448,4.135 0.302,0.198 10 (-)
*1 Solenoid (SL4) Valve


Remove the solenoid (SL4) valve.

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

NG