Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2021.07
RM38G0E _58 Vehicle Interior _100611 METER / GAUGE / DISPLAY _0467504 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B150013  Fuel Sender Circuit Open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B150013 Fuel Sender Circuit Open Diagnosis Condition:
·

Ignition switch ON

·

IG power source voltage is 9.5 V or more


Malfunction Status:
·

Voltage signal from fuel sender gauge assembly is 0.2 V or less

·

Voltage signal from fuel sender gauge assembly is 4.7 V or more


Malfunction Time:

10 seconds or more


·

Harness or connector

·

Fuel sender gauge assembly

·

Fuel suction tube with pump and gauge assembly

·

Combination meter assembly


-

WIRING DIAGRAM

E417158E30
0.292,3.396 4.729,3.594 4.438,0.198 10 false V8 0.302,3.542 4.74,3.74 4.438,0.198 10 false Fuel Suction with Pump and Gauge Tube Assembly 5.417,1.927 5.677,2.104 0.26,0.177 10 false FR 2.198,1.927 2.448,2.104 0.25,0.177 10 false FR 2.5,1.927 2.656,2.115 0.156,0.188 10 false 3 5.094,1.927 5.292,2.135 0.198,0.208 10 false 23 5.156,1.396 5.375,1.604 0.219,0.208 10 false 7 5.083,2.458 5.302,2.667 0.219,0.208 10 false 17 5.406,2.448 5.865,2.635 0.458,0.188 10 false FE&B 5.417,1.396 5.667,1.573 0.25,0.177 10 false FV 6.323,1.135 6.521,1.344 0.198,0.208 10 false IG 2.51,2.458 2.656,2.656 0.146,0.198 10 false 2 2.51,1.375 2.677,1.563 0.167,0.188 10 false 1 1.396,1.396 2,1.698 0.604,0.302 10 false 1 1.365,2.469 1.969,2.771 0.604,0.302 10 false 2 1.365,1.938 2.26,2.271 0.896,0.333 10 false 3 2.188,1.385 2.385,1.552 0.198,0.167 10 false FV 2.208,2.448 2.469,2.625 0.26,0.177 10 false FE 0.531,3.063 2.875,3.323 2.344,0.26 10 false Fuel Sender Gauge Assembly 5.26,3.406 6.927,3.688 1.667,0.281 10 false I5 5.26,3.552 7.125,4.229 1.865,0.677 10 false Combination Meter Assembly 6.333,2.031 6.635,2.25 0.302,0.219 10 false CPU 5.917,2.052 6.094,2.24 0.177,0.188 10 false I/F

CAUTION / NOTICE / HINT

CAUTION:

Be careful of flames.


NOTICE:
·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

When the combination meter assembly is replaced, update the ECU security key.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>UPDATE ECU SECURITY KEY



PROCEDURE

1.INSPECT FUEL SENDER GAUGE ASSEMBLY

OK

2.INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

NG

2.INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
E442852E03
0.385,1.292 0.719,1.521 0.333,0.229 0.375,3.719 0.708,3.948 0.333,0.229 1.344,1.229 0.906,0.708 true 2.083,1.219 2.458,0.615 true 1.729,1.198 1.729,0.469 true 0.521,1.333 0.74,1.531 0.219,0.198 10 false A 0.51,3.76 0.729,3.958 0.219,0.198 10 false B 0.75,0.552 0.969,0.75 0.219,0.198 10 false FV 1.656,0.281 1.875,0.479 0.219,0.198 10 false FE 2.448,0.448 2.667,0.646 0.219,0.198 10 false FR


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (FV) - B-1 Always Below 1 Ω
A-2 (FE) - B-2 Always Below 1 Ω
A-3 (FR) - B-3 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the V8 fuel suction with pump and gauge tube assembly connector.


b.

Disconnect the I5 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(V8,I5)Location & Routing

Click Connector(V8)Body>Differential Wire / Frame Wire>Fuel Suction with Pump & Gage Tube Assembly

Click Connector(I5)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

V8-3 (FR) - I5-23 (FR) Always Below 1 Ω
V8-2 (FE) - I5-17 (FE&B) Always Below 1 Ω
V8-1 (FV) - I5-7 (FV) Always Below 1 Ω
V8-3 (FR) or I5-23 (FR) - Other terminals and body ground Always 10 kΩ or higher
V8-2 (FE) or I5-17 (FE&B) - Other terminals and body ground Always 10 kΩ or higher
V8-1 (FV) or I5-7 (FV) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR