Home › Power Source / Network › F33A-FTV (BATTERY / CHARGING) › CHARGING SYSTEM › from 2021.07
RM38G0E _57 Power Source / Network _106328 F33A-FTV BATTERY / CHARGING _0489033 CHARGING SYSTEM C

F33A-FTV BATTERY / CHARGING  CHARGING SYSTEM  P161A87  Lost Communication with Alternator Missing Message  


DESCRIPTION

The ECM communicates with the generator assembly via LIN communication. If a LIN communication error is detected, the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Note
P161A87 Lost Communication with Alternator Missing Message Generator assembly or ECM communication stops for approximately 17 minutes or more with the ignition switch ON
(1 trip detection logic)
·

Wire harness or connector

·

Generator assembly

·

ECM


Charge warning is displayed SAE: P161A

WIRING DIAGRAM

A488053E02
0.323,0.51 1.24,1.167 0.917,0.656 10 false from Battery 1.635,0.688 2.552,0.927 0.917,0.24 10 false BATT-S NO. 1 2.635,0.396 2.771,0.604 0.135,0.208 10 false 3 2.833,0.521 3.083,0.75 0.25,0.229 10 false +B 3.906,0.719 4.156,0.948 0.25,0.229 10 false LIN 4.24,0.542 4.49,0.771 0.25,0.229 10 false 2 2.698,1.24 3.083,1.5 0.385,0.26 10 false B39 2.698,1.406 4.813,1.635 2.115,0.229 10 false Battery State Sensor Assembly 2.854,2.719 3.24,2.979 0.385,0.26 10 false C53 2.854,2.885 5.146,3.135 2.292,0.25 9 false Generator Assembly 1.083,3.177 3.198,3.406 2.115,0.229 10 false : LIN Communication Line 5.854,0.719 6.146,0.958 0.292,0.24 10 false LIN 5.583,0.542 5.833,0.771 0.25,0.229 10 false 13 5.802,1.802 6.271,2.031 0.469,0.229 10 false B70 5.802,1.979 6.313,2.208 0.51,0.229 10 false ECM 3.875,2.198 4.385,2.427 0.51,0.229 10 false LIN 4.24,2.021 4.49,2.25 0.25,0.229 10 false 2 1.625,1.073 2.542,1.313 0.917,0.24 10 false BATT-S NO. 2 2.844,0.865 3.323,1.104 0.479,0.24 10 false RBAT 2.625,0.75 2.76,0.958 0.135,0.208 10 false 1 0.177,0.094 2.292,0.323 2.115,0.229 10 false w/ Stop and Start System:

E221308E54
1.469,1.031 1.76,1.219 0.292,0.188 10 false LIN 5.667,1.021 6.031,1.198 0.365,0.177 10 false LIN 1.781,0.844 1.938,1.042 0.156,0.198 10 false 2 5.396,0.844 5.833,1.031 0.438,0.188 10 false 13 0.708,1.833 1.021,2.031 0.313,0.198 10 false C53 5.823,2.063 6.396,2.323 0.573,0.26 10 false ECM 5.833,1.875 6.167,2.052 0.333,0.177 10 false B70 0.927,2.344 2.583,2.583 1.656,0.24 10 false : LIN Communication Line 0.698,2 2.021,2.198 1.323,0.198 10 false Generator Assembly 0.167,0.063 3.917,0.281 3.75,0.219 10 false w/o Stop and Start System:

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before replacing the ECM, refer to Service Bulletin.



PROCEDURE

1.CHECK CHARGING SYSTEM

Result:
Result Proceed to
OK (w/ Stop and Start System) A
OK (w/o Stop and Start System) B
NG C



A

2.CHECK HARNESS AND CONNECTOR (ECM - GENERATOR ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (ECM - GENERATOR ASSEMBLY)

C

REPAIR OR REPLACE CHARGING SYSTEM

2.CHECK HARNESS AND CONNECTOR (ECM - GENERATOR ASSEMBLY)
a.

Disconnect the ECM connector.


b.

Disconnect the generator assembly connector.


c.

Disconnect the battery state sensor assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

Click Location & Routing(B39,C53,B70)Location & Routing

Click Connector(B39)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Battery State Sensor Assembly

Click Connector(C53)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Generator with Regulator Assembly

Click Connector(B70)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

B39-2 (LIN) or C53-2 (LIN) - B70-13 (LIN) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(B39,C53,B70)Location & Routing

Click Connector(B39)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Battery State Sensor Assembly

Click Connector(C53)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Generator with Regulator Assembly

Click Connector(B70)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

B39-2 (LIN), C53-2 (LIN) or B70-13 (LIN) - Body ground Ignition switch off
(while LIN communication stopped)
10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CLEAR DTC
a.

Check for DTCs using the GTS, and then write them down.

Powertrain > Engine > Trouble Codes
50001 372

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait 30 seconds.


Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT
a.

Start the engine.


b.

Allow the engine to idle for approximately 17 minutes or more.


c.

Check for DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
Only P161A87 is output A
P161A87 and P162B87 are output B
DTCs are not output C



A

B

C

5.CHECK HARNESS AND CONNECTOR (ECM - GENERATOR ASSEMBLY)
a.

Disconnect the ECM connector.


b.

Disconnect the generator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

Click Location & Routing(C53,B70)Location & Routing

Click Connector(C53)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Generator with Regulator Assembly

Click Connector(B70)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

C53-2 (LIN) - B70-13 (LIN) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(C53,B70)Location & Routing

Click Connector(C53)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Generator with Regulator Assembly

Click Connector(B70)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

C53-2 (LIN) or B70-13 (LIN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR