FUEL RECEIVER GAUGE OPERATION
The combination meter assembly receives the fuel level signal via direct line from the fuel sender gauge assembly and No. 2 fuel sender gauge assembly* and the fuel consumption signal from the ECM via CAN communication, then calculates the fuel level in the fuel tank and displays the calculated value on the fuel receiver gauge.
*: w/ Fuel Sub Tank
FUEL RECEIVER GAUGE READING
During normal driving:
During driving, the value of the fuel receiver gauge is updated based on the reduction in the fuel level. The reduction is calculated by deducting the value calculated based on the fuel consumption signal sent by the ECM from the value calculated based on the signal sent by the fuel sender gauge assembly and No. 2 fuel sender gauge assembly*.
*: w/ Fuel Sub Tank
During refueling:
As the fuel level in the fuel tank increases during refilling, the output value of the fuel sender gauge assembly and No. 2 fuel sender gauge assembly* changes. When the combination meter assembly detects a change in the output value of the fuel sender gauge assembly and No. 2 fuel sender gauge assembly* of a certain value or more, it determines that fuel is being added and calculates the added amount. This control is called refueling judgment and the fuel receiver gauge display is updated in accordance with the fuel level calculated based on the refueling judgment.
*: w/ Fuel Sub Tank
PRECAUTION FOR REFUELING
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>PRECAUTION
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
When replacing the combination meter assembly, update the ECU security key.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>UPDATE ECU SECURITY KEY
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
Before preforming this procedure, check for Meter / Gauge System DTC B150013 or B150113* which is stored if an open or short in the circuit is detected. If DTC B150013 or B150113* is output, perform troubleshooting and repairs as necessary.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
*: w/ Fuel Sub Tank
When the fuel level drops below the following amount, the fuel level warning light illuminates.
8.25 liters (8.7 US qts, 7.3 Imp. qts)
Check if CAN communication DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check if electronically controlled brake system DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Ask the customer about the problem symptoms.
| Result | Proceed to |
|---|---|
| Malfunction occurs when adding fuel (Even when refueled, display value does not increase) | A |
| Malfunction occurs when adding fuel (When refueled, display value increase is slow) | B |
| Malfunction occurs during normal driving (The reading does not change, decreases quickly or decreases when the vehicle is not being driven, etc.) (The problem symptom recurs) (for Gasoline) |
C |
| Malfunction occurs during normal driving (The reading does not change, decreases quickly or decreases when the vehicle is not being driven, etc.) (The problem symptom recurs) (for Diesel) |
D |
| Malfunction occurs during normal driving (The reading does not change, decreases quickly or decreases when the vehicle is not being driven, etc.) (The problem symptom does not recur) |
E |
A
B
C
D
E
Perform a manual update of the fuel receiver gauge.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>PRECAUTION
Check that the display value of the fuel receiver gauge has changed.
| Result | Proceed to |
|---|---|
| Display value of the fuel receiver gauge has changed | A |
| Display value of the fuel receiver gauge has not changed | B |
A
Symptom caused by amount of fuel filled being too low to trigger refueling judgment, or refueling in an undetectable range.
B
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Fuel Gauge Operation (Sender E) | Fuel receiver gauge (Fuel sender gauge lower limit) |
ON | See [Display] |
| Fuel Gauge Operation (Empty) | Fuel receiver gauge (Fuel receiver gauge indicates E) |
ON | See [Display] |
| Fuel Gauge Operation (Warning) | Fuel receiver gauge (Position at which fuel level warning light turns on/off) |
ON | See [Display] |
| Fuel Gauge Operation (1/4) | Fuel receiver gauge (Fuel receiver gauge indicates 1/4) |
ON | See [Display] |
| Fuel Gauge Operation (1/2) | Fuel receiver gauge (Fuel receiver gauge indicates 1/2) |
ON | See [Display] |
| Fuel Gauge Operation (3/4) | Fuel receiver gauge (Fuel receiver gauge indicates 3/4) |
ON | See [Display] |
| Fuel Gauge Operation (Full) | Fuel receiver gauge (Fuel receiver gauge indicates F) |
ON | See [Display] |
| Fuel Gauge Operation (Sender F) | Fuel receiver gauge (Fuel sender gauge upper limit) |
ON | See [Display] |
| Tester Display |
|---|
| Fuel Gauge Operation (Sender E) |
| Tester Display |
|---|
| Fuel Gauge Operation (Empty) |
| Tester Display |
|---|
| Fuel Gauge Operation (Warning) |
| Tester Display |
|---|
| Fuel Gauge Operation (1/4) |
| Tester Display |
|---|
| Fuel Gauge Operation (1/2) |
| Tester Display |
|---|
| Fuel Gauge Operation (3/4) |
| Tester Display |
|---|
| Fuel Gauge Operation (Full) |
| Tester Display |
|---|
| Fuel Gauge Operation (Sender F) |
| *a | Fuel Gauge Operation (Sender E) |
| *b | Fuel Gauge Operation (Empty) |
| *c | Fuel Gauge Operation (Warning) |
| *d | Fuel Gauge Operation (1/4) |
| *e | Fuel Gauge Operation (1/2) |
| *f | Fuel Gauge Operation (3/4) |
| *g | Fuel Gauge Operation (Full) |
| *h | Fuel Gauge Operation (Sender F) |
[Display]: Fuel Gauge Operation (for Type A)
| *a | Fuel Gauge Operation (Sender E) |
| *b | Fuel Gauge Operation (Empty) |
| *c | Fuel Gauge Operation (Warning) |
| *d | Fuel Gauge Operation (1/4) |
| *e | Fuel Gauge Operation (1/2) |
| *f | Fuel Gauge Operation (3/4) |
| *g | Fuel Gauge Operation (Full) |
| *h | Fuel Gauge Operation (Sender F) |
[Display]: Fuel Gauge Operation (for Type B)
| Result | Proceed to |
|---|---|
| Active Test can be performed correctly | A |
| Active Test cannot be performed correctly | B |
A
B
As it is necessary to add more than a certain amount of fuel to the fuel tank, if the fuel level is near full (fuel receiver gauge indicator near F), perform the following procedure then proceed to step (a). If the fuel tank is not near full, proceed to step (a) without performing the following procedure.
Turn the ignition switch off.
Remove 15 liters (15.9 US qts, 13.2 Imp. qts) or more of fuel from the fuel tank.
Turn the ignition switch to ON.
Wait 6 minutes or more.
Confirm that the fuel receiver gauge indicates a value in accordance with the removed amount of fuel.
Record the fuel receiver gauge reading.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
This resets the current fuel level information stored by the combination meter assembly.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Drive the vehicle at 2 km/h (1 mph) or more, and then stop the vehicle on a flat surface.
Turn the ignition switch off.
Wait 30 seconds or more.
Add the following amount of fuel or more.
5.0 liters (5.3 US qts, 4.4 Imp. qts)
Turn the ignition switch to ON.
Check that the fuel receiver gauge reading increases in proportion to the amount of fuel added.
After turning the ignition switch to ON, it may take approximately 30 seconds until the fuel receiver gauge indicates the determined value.
| Result | Proceed to |
|---|---|
| Fuel receiver gauge reading increases in proportion to the amount of fuel added | A |
| Fuel receiver gauge reading does not change even when fuel is added | B |
A
B
Check if SFI system DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
for V35A-FTS: Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Fuel Gauge Operation (Sender E) | Fuel receiver gauge (Fuel sender gauge lower limit) |
ON | See [Display] |
| Fuel Gauge Operation (Empty) | Fuel receiver gauge (Fuel receiver gauge indicates E) |
ON | See [Display] |
| Fuel Gauge Operation (Warning) | Fuel receiver gauge (Position at which fuel level warning light turns on/off) |
ON | See [Display] |
| Fuel Gauge Operation (1/4) | Fuel receiver gauge (Fuel receiver gauge indicates 1/4) |
ON | See [Display] |
| Fuel Gauge Operation (1/2) | Fuel receiver gauge (Fuel receiver gauge indicates 1/2) |
ON | See [Display] |
| Fuel Gauge Operation (3/4) | Fuel receiver gauge (Fuel receiver gauge indicates 3/4) |
ON | See [Display] |
| Fuel Gauge Operation (Full) | Fuel receiver gauge (Fuel receiver gauge indicates F) |
ON | See [Display] |
| Fuel Gauge Operation (Sender F) | Fuel receiver gauge (Fuel sender gauge upper limit) |
ON | See [Display] |
| Tester Display |
|---|
| Fuel Gauge Operation (Sender E) |
| Tester Display |
|---|
| Fuel Gauge Operation (Empty) |
| Tester Display |
|---|
| Fuel Gauge Operation (Warning) |
| Tester Display |
|---|
| Fuel Gauge Operation (1/4) |
| Tester Display |
|---|
| Fuel Gauge Operation (1/2) |
| Tester Display |
|---|
| Fuel Gauge Operation (3/4) |
| Tester Display |
|---|
| Fuel Gauge Operation (Full) |
| Tester Display |
|---|
| Fuel Gauge Operation (Sender F) |
| *a | Fuel Gauge Operation (Sender E) |
| *b | Fuel Gauge Operation (Empty) |
| *c | Fuel Gauge Operation (Warning) |
| *d | Fuel Gauge Operation (1/4) |
| *e | Fuel Gauge Operation (1/2) |
| *f | Fuel Gauge Operation (3/4) |
| *g | Fuel Gauge Operation (Full) |
| *h | Fuel Gauge Operation (Sender F) |
[Display]: Fuel Gauge Operation (for Type A)
| *a | Fuel Gauge Operation (Sender E) |
| *b | Fuel Gauge Operation (Empty) |
| *c | Fuel Gauge Operation (Warning) |
| *d | Fuel Gauge Operation (1/4) |
| *e | Fuel Gauge Operation (1/2) |
| *f | Fuel Gauge Operation (3/4) |
| *g | Fuel Gauge Operation (Full) |
| *h | Fuel Gauge Operation (Sender F) |
[Display]: Fuel Gauge Operation (for Type B)
| Result | Proceed to |
|---|---|
| Active Test can be performed correctly | A |
| Active Test cannot be performed correctly | B |
A
B
Record the fuel receiver gauge reading.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
This resets the current fuel level information stored by the combination meter assembly.
Connect the cable to the negative (-) battery terminal.
Wait 30 seconds or more.
Turn the ignition switch to ON.
Check if the fuel receiver gauge reading corresponds with the amount of fuel remaining in the fuel tank.
After turning the ignition switch to ON, it may take approximately 30 seconds until the fuel receiver gauge indicates the determined value.
| Result | Proceed to |
|---|---|
| Fuel receiver gauge reading corresponds with the amount of fuel remaining in the fuel tank | A |
| Fuel receiver gauge reading does not correspond with the amount of fuel remaining in the fuel tank | B |
A
B
Check if ECD system DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
w/ DPF:
w/o DPF:
Inspect the fuel tank assembly and fuel sender gauge assembly for deformation, foreign matter or an improperly installed fuel receiver gauge, as this may be the cause of the fuel receiver gauge malfunction.
Visually check the fuel tank assembly for any abnormalities.
Check if there is an excessive amount of foreign matter in the fuel tank assembly.
Visually check the fuel sender gauge assembly and No. 2 fuel sender gauge assembly* for damage and confirm that it operates correctly.
Check the installation condition of the fuel tank assembly fuel sender gauge assembly and No. 2 fuel sender gauge assembly*.
*: w/ Fuel Sub Tank
| Result | Proceed to |
|---|---|
| Normal | A |
| Appearance of the fuel tank assembly is abnormal | B |
| There is an excessive amount of foreign matter in the fuel tank assembly | C |
| The fuel sender gauge assembly or No. 2 fuel sender gauge assembly is visually damaged or does not operate correctly | D |
| The fuel tank assembly, fuel sender gauge assembly or No. 2 fuel sender gauge assembly is not installed correctly | E |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE (FUEL)>FUEL TANK>REMOVAL
for V35A-FTS: Click hereEngine / Hybrid System>V35A-FTS (FUEL)>FUEL TANK>REMOVAL
for F33A-FTV: Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL TANK>REMOVAL
C
D
for 1GR-FE:
Click hereEngine / Hybrid System>1GR-FE (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
for V35A-FTS:
Click hereEngine / Hybrid System>V35A-FTS (FUEL)>FUEL SENDER GAUGE ASSEMBLY (for Double Tank Type)>REMOVAL
for F33A-FTV:
Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL SENDER GAUGE ASSEMBLY (for Double Tank Type)>REMOVAL
E