| *A | for Single Tank Type | *B | for Double Tank Type |
| *1 | FUEL TANK FILLER PIPE | *2 | PIN |
| *3 | FUEL TANK BAND | - | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the fuel sub tank sub-assembly removal/installation are shown below.
When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Never perform work on fuel system components near any possible ignition sources.
Vaporized fuel could ignite, resulting in a serious accident.
Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.
Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
The fuel tank sub-assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank sub-assembly may fall off the engine lifter.
1.DISCHARGE FUEL SYSTEM PRESSURE
2. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
17420 4.REMOVE CENTER EXHAUST PIPE ASSEMBLY
37110F 5.REMOVE REAR PROPELLER SHAFT ASSEMBLY
77310A 6.REMOVE FUEL TANK CAP ASSEMBLY
77020A 7.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
for Single Tank Type:
Click hereEngine / Hybrid System>V35A-FTS (FUEL)>FUEL PUMP (for Single Tank Type)>REMOVAL
for Double Tank Type:
Click hereEngine / Hybrid System>V35A-FTS (FUEL)>FUEL PUMP (for Double Tank Type)>REMOVAL
77607C 8.REMOVE NO. 2 FUEL TANK PROTECTOR SUB-ASSEMBLY
9.DISCONNECT NO. 1 FUEL TANK BREATHER TUBE SUB-ASSEMBLY
Disconnect the No. 1 fuel tank breather tube sub-assembly from the fuel tank filler pipe.
Click hereEngine / Hybrid System>V35A-FTS (FUEL)>FUEL SYSTEM>PRECAUTION
77213E 10.DISCONNECT FUEL TANK TO FILLER PIPE HOSE
77259C 11.DISCONNECT FUEL HOSE (for Single Tank Type)
77262 12.DISCONNECT NO. 2 FUEL EMISSION TUBE (for Double Tank Type)
Disconnect the No. 2 fuel emission tube.
Click hereEngine / Hybrid System>V35A-FTS (FUEL)>FUEL SYSTEM>PRECAUTION
77209C 13.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
Disconnect the fuel tank main tube sub-assembly.
Click hereEngine / Hybrid System>V35A-FTS (FUEL)>FUEL SYSTEM>PRECAUTION
77001A 14.REMOVE FUEL TANK SUB-ASSEMBLY
|
|
Using an engine lifter and attachments, support the fuel tank sub-assembly.
Remove the 2 bolts, 2 clips, 2 pins and 2 fuel tank bands.
Slightly lower the engine lifter.
77209C 15.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY
77642A 16.REMOVE NO. 2 FUEL TANK PROTECTOR
77259C 17.REMOVE FUEL HOSE (for Single Tank Type)
77213E 18.REMOVE FUEL TANK TO FILLER PIPE HOSE
77697 19.REMOVE NO. 1 FUEL TANK HEAT INSULATOR
Using a needle nose pliers, detach the 4 clips and remove the No. 1 fuel tank heat insulator from the fuel tank sub-assembly.
77697A 20.REMOVE NO. 2 FUEL TANK HEAT INSULATOR
Using a needle nose pliers, detach the 5 clips and remove the No. 2 fuel tank heat insulator from the fuel tank sub-assembly.