Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2021.07
RM38G0E _58 Vehicle Interior _100611 METER / GAUGE / DISPLAY _0467504 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Tachometer Malfunction  


DESCRIPTION

In this circuit, the combination meter assembly receives engine speed signals from the ECM via CAN communication. The combination meter assembly displays the engine speed calculated based on the data received from the ECM.

WIRING DIAGRAM

E407708E04
4.667,1.583 6.542,1.917 1.875,0.333 10 false Combination Meter Assembly 0.698,2.26 2.781,2.563 2.083,0.302 10 false : CAN Communication Line 1.677,1.604 3.323,2.042 1.646,0.438 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

Before replacing the ECM, refer to Service Bulletin.



PROCEDURE

1.READ VALUE USING GTS (ENGINE RPM)
a.

Using the GTS, read the Data List.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine RPM Engine speed Min.: 0 rpm, Max.: 12750 rpm Actual engine speed -
Body Electrical > Combination Meter > Data List
Tester Display
Engine RPM
50003 409 24
HINT:
·

When the Data List values of the ECUs match, an internal malfunction of the ECM is suspected.

·

When the Data List values of the ECUs do not match, a signal output error of the ECM or an internal malfunction of the combination meter assembly is suspected.



OK:

The Data List values of the ECUs do not match.



Result:
Result Proceed to
OK A
NG (for Gasoline) B
NG (for Diesel) C



A

REPLACE COMBINATION METER ASSEMBLY

B

2.CHECK FOR DTC (SFI SYSTEM)

C

4.CHECK FOR DTC (ECD SYSTEM)
2.CHECK FOR DTC (SFI SYSTEM)
a.

Check if SFI system DTCs are output.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (ENGINE RPM, ENGINE SPEED)

NG

3.READ VALUE USING GTS (ENGINE RPM, ENGINE SPEED)
a.

Using the GTS, read the Data List.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine RPM Engine speed Min.: 0 rpm, Max.: 12750 rpm Actual engine speed -
Body Electrical > Combination Meter > Data List
Tester Display
Engine RPM
50003 409 24
Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Speed Engine speed Min.: 0 rpm, Max.: 16383 rpm
for V35A-FTS:

600 to 800 rpm: Idling (shift lever in P, engine warmed up and A/C off)


for 1GR-FE:

550 to 700 rpm: Idling (shift lever in N, engine warmed up and A/C off)


for F33A-FTV:
·

50 to 400 rpm: Cranking

·

550 to 650 rpm: Idling with warm engine


-
Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 372 211
HINT:
·

When the Data List values of the ECUs match, an internal malfunction of the ECM is suspected.

·

When the Data List values of the ECUs do not match, a signal output error of the ECM or an internal malfunction of the combination meter assembly is suspected.



OK:

The Data List values of the ECUs do not match.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

4.CHECK FOR DTC (ECD SYSTEM)
a.

Check if ECD system DTCs are output.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (ENGINE RPM, ENGINE SPEED)

NG