| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Note |
|---|---|---|---|---|---|
| C124A00 | ECM Communication | Either of the following is detected:
·
The engine type, powertrain variation and destination information sent from the ECM do not match the information stored in the No. 2 skid control ECU (brake actuator assembly).
·
No system information stored in the No. 2 skid control ECU (brake actuator assembly). |
·
Incorrect ECM installed
·
No. 2 skid control ECU (brake actuator assembly) |
Brake/EPB | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | - | - | - |
| Malfunction Status | The engine type, powertrain variation and destination information sent from the ECM do not match the information stored in the No. 2 skid control ECU (brake actuator assembly) | ○ | - |
| No system information stored in the No. 2 skid control ECU (brake actuator assembly) | - | ○ | |
| Detection Time | - | - | |
| Number of Trips | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY
Check that the proper ECM is installed.
Proper ECM is installed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>ECM>REMOVAL
for V35A-FTS: Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>ECM>REMOVAL
for F33A-FTS: Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
Check that the proper No. 2 skid control ECU (brake actuator assembly) is installed.
Proper No. 2 skid control ECU (brake actuator assembly) is installed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for RHD)>REMOVAL
Perform system information memorization.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY
| Tester Display |
|---|
| Reset Memory |
| Tester Display |
|---|
| Calibration |
After performing "Reset Memory" using the GTS to clear the memorized value of the No. 2 skid control ECU (brake actuator assembly), DTC C124A00 will be stored until system information memorization is performed.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| C124A00 is not output | A |
| C124A00 is output | B |
A
B
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for RHD)>REMOVAL