The fuel temperature sensor (for fuel filter) is installed to the fuel filter and measures the fuel temperature. When the temperature is extremely low, it operates the PTC heater, warms fuel and ensures startability.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P018011 | Fuel Temperature Sensor "A" Circuit Short to Ground | Short in the fuel temperature sensor (for fuel filter) circuit for 3 seconds. (1 trip detection logic) |
·
Short in fuel temperature sensor (for fuel filter)circuit
·
Fuel temperature sensor (for fuel filter)
·
ECM |
Does not come on | SAE Code: P0182 |
| P018015 | Fuel Temperature Sensor "A" Circuit Short to Battery or Open | Open in the fuel temperature sensor (for fuel filter) circuit for 3 seconds. (1 trip detection logic) |
·
Open in fuel temperature sensor (for fuel filter)circuit
·
Fuel temperature sensor (for fuel filter)
·
ECM |
Does not come on | SAE Code: P0183 |
| DTC No. | Data List |
|---|---|
| P018011 P018015 |
- |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P018011 P018015 |
Ignition switch ON for 3 second or more |
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL TEMPERATURE SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the fuel temperature sensor (for fuel filter) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(V18,B70)Location & Routingewd_type=routing;type=c,c;code=V18,B70 Click Connector(V18)Body>Differential Wire / Frame Wire>Fuel Temperature Sensorewd_type=component;type=c;code=V18;pinno=2,1 |
||
| V18-2 (THF) - B70-50 (THPT) | Always | Below 1 Ω |
| V18-1 (E2) - B70-49 (ETPT) | Always | Below 1 Ω |
| V18-2 (THF) or B70-50 (THPT) - Body ground and other terminals | Always | 10 kΩ or higher |
| V18-1 (E2) or B70-49 (ETPT) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch to ON and wait for 0.5 second or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the fuel temperature sensor (for fuel filter).
Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL TEMPERATURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT