Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484891 ECD SYSTEM(w/o DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P048771  Exhaust Gas Recirculation Throttle Control Circuit "A" Range/Performance Actuator Stuck  


DESCRIPTION

The ECM opens and closes the throttle valve using a DC motor type actuator. Due to the opening and closing of the valve, the exhaust gas recirculation volume can be properly controlled. Also, engine vibration and noise will be reduced by closing the valve when the engine is stopped.

Although the DTC title says "Exhaust Gas Recirculation Throttle Position Control Range / Performance", this DTC indicates that the throttle valve is malfunctioning.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P048771 Exhaust Gas Recirculation Throttle Control Circuit "A" Range/Performance Actuator Stuck The throttle actuator activation duty is more than specified value for 60 seconds.
(1 trip detection logic)
·

Throttle valve stuck

·

Throttle valve does not move smoothly

·

Open or short in throttle actuator circuit

·

ECM


Comes on SAE Code: P0488

Related Data List
DTC No. Data List
P048771
·

Target Throttle Position Bank 1

·

Actual Throttle Position Bank 1

·

Diesel Throttle Motor Duty Bank 1

·

Throttle Close Learning Value Bank 1



Reference
Condition Throttle Valve Position
Moment when accelerator pedal is depressed further or released at 3000 rpm Throttle valve opening angle varies smoothly

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P048771 Perform the following repeatedly for 1 minute:
Gradually raise the engine speed to 3000 rpm from idling over approximately 10 seconds, and then release the accelerator pedal to return to an idling state.

MONITOR DESCRIPTION

The ECM opens and closes the throttle valve by adjusting the current flowing to the DC motor with a duty ratio. If the throttle valve does not move smoothly or is stuck, the duty ratio used during valve movement control increases or decreases greatly. The ECM will determine that the throttle valve is malfunctioning and illuminate the MIL.

A206049E11
4.573,2.135 4.708,1.792 false 4.563,2.896 4.698,2.563 false 4.563,3.646 4.698,3.302 false 4.698,4.479 4.594,4.188 false 5.302,5.24 5.125,5.031 false 3.448,5.198 3.219,5.021 false 0.25,5.438 1.646,5.802 1.396,0.365 10 false Duty Ratio Malfunction Counter 0.094,0.031 1.875,0.24 1.781,0.208 10 false Malfunction Detection: 0.25,1.25 1.656,1.615 1.406,0.365 10 false Throttle Valve Target Opening Angle 0.25,2.708 1.729,3.104 1.479,0.396 10 false Throttle Valve Actual Opening Angle 0.906,4.125 1.646,4.344 0.74,0.219 10 false Duty Ratio 4.75,1.719 5.344,1.917 0.594,0.198 10 false Normal 4.75,2.479 5.5,2.677 0.75,0.198 10 false Abnormal 4.75,4.375 5.344,4.573 0.594,0.198 10 false Normal 4.75,3.219 5.5,3.417 0.75,0.198 10 false Abnormal 5.906,0.594 6.354,0.792 0.448,0.198 10 false Open 5.906,1.354 6.385,1.552 0.479,0.198 10 false Close 5.906,2.063 6.354,2.26 0.448,0.198 10 false Open 5.906,2.823 6.385,3.021 0.479,0.198 10 false Close 5.906,3.573 6.417,3.781 0.51,0.208 10 false 100% 5.906,4.333 6.25,4.531 0.344,0.198 10 false 0% 3.49,5.104 4.521,5.313 1.031,0.208 10 false Stores P048771 5.302,5.24 6.094,5.448 0.792,0.208 10 false Threshold 3.469,6.271 3.875,6.479 0.406,0.208 10 false Time

CAUTION / NOTICE / HINT

NOTICE:
·

When cleaning the diesel throttle body assembly, use a piece of cloth soaked with cleaning solvent. Spraying solvent directly onto these parts or soaking the parts in solvent may damage the parts.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (DIESEL THROTTLE TARGET ANGLE BANK 1)
a.

Enter the following menus: Powertrain / Engine / Active Test / Diesel Throttle Target Angle Bank 1 / Primary / Actual Throttle Position Bank 1.

Powertrain > Engine > Active Test
Active Test Display
Diesel Throttle Target Angle Bank 1
Data List Display
Actual Throttle Position Bank 1
50004 372 72 1110

b.

When changing the Active Test value consecutively to 10, 30, 60, 90, 60, 30 and 10%, check that Actual Throttle Position Bank 1 smoothly changes to the set opening angle.

OK:

Value smoothly changes to set opening angle.



Result:
Proceed to
OK
NG



OK

2.CHECK FOR DEPOSIT (DIESEL THROTTLE BODY ASSEMBLY)

NG

8.CHECK FOR DEPOSIT (DIESEL THROTTLE BODY ASSEMBLY)
2.CHECK FOR DEPOSIT (DIESEL THROTTLE BODY ASSEMBLY)
a.

Visually check for deposits in the diesel throttle body assembly. If there are deposits, clean the diesel throttle body assembly.

NOTICE:
·

When cleaning the diesel throttle body assembly, use a piece of cloth soaked with cleaning solvent. Spraying solvent directly onto these parts or soaking the parts in solvent may damage the parts.

·

Extreme care must be taken to prevent the removed deposits from falling into the engine unit during cleaning.




Result:
Proceed to
NEXT



NEXT

3.INSPECT DIESEL THROTTLE BODY ASSEMBLY (THROTTLE VALVE MOVEMENT)
3.INSPECT DIESEL THROTTLE BODY ASSEMBLY (THROTTLE VALVE MOVEMENT)
a.

Using your finger, move the throttle valve from the fully open position to the fully closed position and check that it moves smoothly.

OK:

Throttle valve moves smoothly.


NOTICE:

Take care not to damage the throttle valve or valve housing.



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P048771)

NG

7.REPLACE DIESEL THROTTLE BODY ASSEMBLY
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P048771)
a.

Start the engine and warm it up.


b.

Take a snapshot with the GTS.


c.

Enter the following menus: Powertrain / Engine / Active Test / Diesel Throttle Target Angle Bank 1 / Primary / Actual Throttle Position Bank 1.

Powertrain > Engine > Active Test
Active Test Display
Diesel Throttle Target Angle Bank 1
Data List Display
Actual Throttle Position Bank 1
50004 372 72 1110
HINT:

The movement of the throttle valve can be determined by performing the following inspection.



d.

When changing the Active Test value consecutively to 10, 30, 60, 90, 60, 30 and 10%, check that Actual Throttle Position Bank 1 smoothly changes to the set opening angle.

OK:

Value smoothly changes to set opening angle.



e.

Perform the following repeatedly for 1 minute: gradually raise the engine speed to 3000 rpm from an idling over approximately 10 seconds, and then release the accelerator pedal to return to an idling state.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

g.

Read the DTCs.

OK:

DTC is not output.



Result:
Proceed to
OK
NG



OK

END

NG

5.REPLACE ECM
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Start the engine and warm it up.


b.

Take a snapshot with the GTS.


c.

Enter the following menus: Powertrain / Engine / Active Test / Diesel Throttle Target Angle Bank 1 / Primary / Actual Throttle Position Bank 1.

Powertrain > Engine > Active Test
Active Test Display
Diesel Throttle Target Angle Bank 1
Data List Display
Actual Throttle Position Bank 1
50004 372 72 1110
HINT:

The movement of the throttle valve can be determined by performing the following inspection.



d.

When changing the Active Test value consecutively to 10, 30, 60, 90, 60, 30 and 10%, check that Actual Throttle Position Bank 1 smoothly changes to the set opening angle.

OK:

Value smoothly changes to set opening angle.



e.

Perform the following repeatedly for 1 minute: gradually raise the engine speed to 3000 rpm from an idling over approximately 10 seconds, and then release the accelerator pedal to return to an idling state.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

g.

Confirm that the DTC is not output.


Result:
Proceed to
NEXT



NEXT

END

7.REPLACE DIESEL THROTTLE BODY ASSEMBLY
a.

Replace the diesel throttle body assembly.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CHECK FOR DEPOSIT (DIESEL THROTTLE BODY ASSEMBLY)
a.

Visually check for deposits in the diesel throttle body assembly. If there are deposits, clean the diesel throttle body assembly.

NOTICE:
·

When cleaning the diesel throttle body assembly, use a piece of cloth soaked with cleaning solvent. Spraying solvent directly onto these parts or soaking the parts in solvent may damage the parts.

·

Extreme care must be taken to prevent the removed deposits from falling into the engine unit during cleaning.




Result:
Proceed to
NEXT



NEXT

9.INSPECT DIESEL THROTTLE BODY ASSEMBLY (THROTTLE VALVE MOVEMENT)
9.INSPECT DIESEL THROTTLE BODY ASSEMBLY (THROTTLE VALVE MOVEMENT)
a.

Using your finger, move the throttle valve from the fully open position to the fully closed position and check that it moves smoothly.

OK:

Throttle valve moves smoothly.


NOTICE:

Take care not to damage the throttle valve or valve housing.



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (DIESEL THROTTLE BODY ASSEMBLY - ECM)

NG

7.REPLACE DIESEL THROTTLE BODY ASSEMBLY
10.CHECK HARNESS AND CONNECTOR (DIESEL THROTTLE BODY ASSEMBLY - ECM)
a.

Disconnect the diesel throttle body assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C177,C138)Location & Routing

Click Connector(C177)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Diesel Throttle Body Assembly

Click Connector(C138)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

C177-2 (VC) - C138-116 (VCVL) Always Below 1 Ω
C177-1 (VTA) - C138-69 (VLU) Always Below 1 Ω
C177-4 (E2) - C138-115 (EVLU) Always Below 1 Ω
C177-6 (M+) - C138-5 (M+) Always Below 1 Ω
C177-5 (M-) - C138-24 (M-) Always Below 1 Ω
C177-2 (VC) or C138-116 (VCVL) - Body ground and other terminals Always 10 kΩ or higher
C177-1 (VTA) or C138-69 (VLU) - Body ground and other terminals Always 10 kΩ or higher
C177-4 (E2) or C138-115 (EVLU) - Body ground and other terminals Always 10 kΩ or higher
C177-6 (M+) or C138-5 (M+) - Body ground and other terminals Always 10 kΩ or higher
C177-5 (M-) or C138-24 (M-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE DIESEL THROTTLE BODY ASSEMBLY

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED