Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484891 ECD SYSTEM(w/o DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P062712  Fuel Pump "A" Control Circuit Short to Battery  P062714  Fuel Pump "A" Control Circuit Short to Ground or Open  P263212  Fuel Pump "B" Control Circuit High Circuit Short to Battery  P263214  Fuel Pump "B" Control Circuit Low Circuit Short to Ground or Open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P062712 Fuel Pump "A" Control Circuit Short to Battery Short in pre-stroke control valve (Bank 1) circuit for 0.5 seconds.
(1 trip detection logic)
·

Short in pre-stroke control valve (Bank 1) circuit

·

Fuel supply pump assembly

·

ECM


Comes on SAE Code: P0629
P062714 Fuel Pump "A" Control Circuit Short to Ground or Open Open or short in pre-stroke control valve (Bank 1) circuit for 0.5 seconds.
(1 trip detection logic)
·

Open or short in pre-stroke control valve (Bank 1) circuit

·

Fuel supply pump assembly

·

ECM


Comes on SAE Code: P0628
P263212 Fuel Pump "B" Control Circuit High Circuit Short to Battery Short in pre-stroke control valve (Bank 2) circuit for 0.5 seconds.
(1 trip detection logic)
·

Short in pre-stroke control valve (Bank 2) circuit

·

Fuel supply pump assembly

·

ECM


Comes on SAE Code: P2634
P263214 Fuel Pump "B" Control Circuit Low Circuit Short to Ground or Open Open or short in pre-stroke control valve (Bank 2) circuit for 0.5 seconds.
(1 trip detection logic)
·

Open or short in pre-stroke control valve (Bank 2) circuit

·

Fuel supply pump assembly

·

ECM


Comes on SAE Code: P2633

Related Data List
DTC No. Data List
P062712
P062714
P263212
P263214
·

Fuel Pressure (High)

·

Target Fuel Pressure (High)



HINT:

When DTC P062712, P062714, P263212 or P263214 is stored, check the internal fuel pressure of the common rail by entering the following menus on the GTS: Powertrain / Engine / Data List / Fuel Pressure (High).

Under a stable operating condition such as idling, Fuel Pressure (High) is within 3500 kPag of Target Fuel Pressure (High).


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P062712
P062714
P263212
P263214
Idling for 1 second or more

WIRING DIAGRAM

A494482E02
0.365,1.792 4.083,2.052 3.719,0.26 10 false Pre-stroke Control Valve (Bank 1) 0.354,1.646 0.969,1.844 0.615,0.198 10 false C166 1.583,1.188 2.042,1.385 0.458,0.198 10 false PCV 1.688,0.51 2.146,0.708 0.458,0.198 10 false +B 2.01,0.51 2.167,0.708 0.156,0.198 10 false 1 2.021,1.177 2.177,1.375 0.156,0.198 10 false 2 0.344,3.906 0.958,4.104 0.615,0.198 10 false C167 0.354,4.063 3.875,4.26 3.521,0.198 10 false Pre-stroke Control Valve (Bank 2) 1.51,3.406 1.969,3.604 0.458,0.198 10 false PCV2 1.688,2.74 2.146,2.938 0.458,0.198 10 false +B 1.958,2.75 2.115,2.948 0.156,0.198 10 false 1 1.99,3.385 2.146,3.583 0.156,0.198 10 false 2 5.594,1.292 6.052,1.49 0.458,0.198 10 false PCV- 5.583,0.604 6.042,0.802 0.458,0.198 10 false PCV+ 5.573,2.865 6.031,3.063 0.458,0.198 10 false PV2+ 5.573,3.531 6.031,3.729 0.458,0.198 10 false PV2- 5.292,1.188 5.604,1.385 0.313,0.198 10 false 30 5.281,0.531 5.594,0.729 0.313,0.198 10 false 29 5.333,3.417 5.646,3.615 0.313,0.198 10 false 9 5.333,2.781 5.646,2.979 0.313,0.198 10 false 8 5.917,3.906 6.531,4.104 0.615,0.198 10 false C138 5.917,4.094 6.49,4.302 0.573,0.208 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT FUEL SUPPLY PUMP ASSEMBLY (PRE-STROKE CONTROL VALVE)
a.

Inspect the pre-stroke control valve.

Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL SUPPLY PUMP>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (PRE-STROKE CONTROL VALVE - ECM)

NG

7.REPLACE FUEL SUPPLY PUMP ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (PRE-STROKE CONTROL VALVE - ECM)
a.

Disconnect the pre-stroke control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C166,C138,C167)Location & Routing

Click Connector(C166)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>No. 1 Pre-stroke Control Valve (Injection or Supply Pump Assembly)

Click Connector(C138)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C167)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>No. 2 Pre-stroke Control Valve (Injection or Supply Pump Assembly)

C166-1 (+B) - C138-29 (PCV+) Always Below 1 Ω
C166-2 (PCV) - C138-30 (PCV-) Always Below 1 Ω
C167-1 (+B) - C138-8 (PV2+) Always Below 1 Ω
C167-2 (PCV2) - C138-9 (PV2-) Always Below 1 Ω
C166-1 (+B) or C138-29 (PCV+) - Body ground and other terminals Always 10 kΩ or higher
C166-2 (PCV) or C138-30 (PCV-) - Body ground and other terminals Always 10 kΩ or higher
C167-1 (+B) or C138-8 (PV2+) - Body ground and other terminals Always 10 kΩ or higher
C167-2 (PCV2) or C138-9 (PV2-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK WHETHER DTC OUTPUT RECURS

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK WHETHER DTC OUTPUT RECURS
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Start the engine and idle it for 1 second or more.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

d.

Read the DTCs.

Result:
Result Proceed to
No DTC is output A
DTC P062712, P062714, P263212 or P263214 is output B




A

END

B

4.REPLACE ECM
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Start the engine and idle it for 1 second or more.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

7.REPLACE FUEL SUPPLY PUMP ASSEMBLY
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.BLEED AIR FROM FUEL SYSTEM
8.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED