Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484891 ECD SYSTEM(w/o DPF) J

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  White Smoke Emitted  


DESCRIPTION

Faults and Symptoms of Common Rail Diesel Components


a.

Engine Control

Turbocharger System
Main fault Turbocharger sub-assembly (compressor side seal ring, turbine side seal ring, shaft, oil drain)
Symptoms White smoke
Excessive oil consumption

Glow System
Main fault Glow system malfunction
Symptoms Difficult to start, rough idle, knocking, white smoke (when cold)
Diagnostic Point
·

Measure the resistance of the glow plug assembly

·

Check the glow plug indicator light



Engine
Main fault Loss of compression
Symptoms Rough idle (constant lack of power)
Data List Engine Speed Cylinder #1 to #6
·

When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder (approx. 100 rpm more than the other cylinders), that cylinder may lose compression.


Injection Feedback Value #1 to #6
·

If Injection Feedback Value #1 to #6 is more than 4.9 mm3/st, the cylinder may have a fault.




b.

Diesel Injection

Injector Assembly
Main fault Blockage
Symptoms Rough idle, lack of power, black smoke, white smoke, knocking
Data List Injection Feedback Value #1 to #6
·

When an Injector Feedback Value is more than 4.9 mm3/st, there may be a malfunction in the corresponding cylinder. Injection Feedback Value #1 to #6 can be read after idling for 1 minute with the engine warmed up (engine coolant temperature is higher than 75°C (167°F)).



HINT:

When the sliding resistance of the internal parts of the injector assemblies (nozzle needle, control valve) has increased due to internal contamination, injection quantity will increase at high common rail pressure due to a delay in injector assembly closure.


Poor Quality Fuel
Main fault -
Symptoms Difficult to start, rough idle (especially when cold)


c.

Diesel EGR

EGR System
Main fault
·

Does not move smoothly

·

Does not close fully


Symptoms
·

Rough idle

·

EGR valve stuck closed: A loud turbocharger sound.

·

EGR valve stuck open: Difficult to start (does not stall), black smoke, white smoke (when engine is cold), lack of power, jerking (If there is an excess in the quantity of EGR and there is a heavy load, when the vehicle starts moving, a lack of power will be felt. Also, when racing the engine, there will be some black smoke).


Data List Actual EGR Valve Position No.1, Target EGR Valve Position No.1
·

Generally, Actual EGR Valve Position No.1 = Target EGR Valve Position No.1 +/-5% (fully closed: 0%, fully open: 100%).

·

Using the EGR valve Active Test, check whether Actual EGR Valve Position No.1 follows Target EGR Valve Position No.1 (the engine coolant temperature and intake air temperature should be considered when a malfunction occurs).

·

EGR valve is fully closed when the ignition switch is ON (engine stopped).

·

EGR valve opens to the halfway point at idling after the engine is warmed up.

·

When the EGR valve does not close, Mass Air Flow Sensor (Mass Air Flow Sub-assembly) decreases when the vehicle is accelerated at full throttle. Intake Manifold Absolute Pressure also decreases in comparison to Target Boost Pressure, however there is not a large difference.


EGR Close Learning Value Bank 1
·

When leaving the vehicle idling, the normal range of EGR Close Learning Value Bank 1 is 0 to 1 V.

·

In cases when EGR Close Learning Value Bank 1 is out of the normal range (0 to 1 V), it is possible that the EGR valve cannot completely close.





CAUTION / NOTICE / HINT

Explanation of Symptom


White Smoke When the engine is misfiring, any fuel that has been injected but remains unburned is emitted as white smoke.
Turbocharger internal oil leak (Click here (Click here))
If oil leak occurs from turbine side seal, large amount of white smoke will be emitted from exhaust pipe.
Internal oil leak is not visible from outside of turbocharger sub-assembly.


PROCEDURE

1.CONFIRM CONDITIONS PRESENT WHEN WHITE SMOKE APPEARED WITH CUSTOMER
a.

Ask the customer about the conditions when the white smoke was emitted.

- What were the driving conditions when the white smoke was generated.

- Is the white smoke constantly emitted, or only occasionally?

- Does the white smoke occur only when the vehicle is cold, or when the vehicle is both cold and hot?

- Is the white smoke emitted just after starting the vehicle only, or does it continue while the vehicle is idling?


b.

Determine the symptoms of the problem to narrow down the possible causes.


Result:
Proceed to
NEXT



NEXT

2.READ OUTPUT DTCS (RELATING TO ENGINE)
2.READ OUTPUT DTCS (RELATING TO ENGINE)
a.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

b.

Read pending DTCs.

Result:
Result Proceed to
No DTCs are output A
Engine related DTCs are output B




A

3.CHECK WHEN WHITE SMOKE IS EMITTED

B

GO TO DTC CHART

3.CHECK WHEN WHITE SMOKE IS EMITTED
a.

Start the engine.


b.

Fully depress the accelerator pedal, and then release it.


c.
A221583C03
0.291,0.017 0.94,0.228 0.649,0.212 10 *a
*a Example


Check whether white smoke is emitted or not when racing the engine.

NOTICE:

Be sure not to check for white smoke indoors.


HINT:
·

If the white smoke is emitted only just after engine start and disappears later, the smoke is not from the turbocharger.

·

If the turbocharger is the cause of the problem, regardless of whether the engine is cold or warmed up, there will be a large amount of white smoke to the extent that visibility is obstructed for a few meters in the area of the smoke (as shown in the illustration).

·

Depending on whether there is oil mixed with the fuel, or whether there is unburned fuel present, the smell of the exhaust gas differs. When oil is mixed in, the exhaust gas smells such as burning oil.

·

When continuously traveling with the engine close to idle for 1 hour or more, such as when in heavy traffic, unburned fuel accumulates in the catalytic converter, and can produce white smoke when accelerating.



Result:
Result Proceed to
White smoke is emitted just after engine start only A
White smoke is always and continuously emitted B
There is oil on the exhaust pipe, etc.
HINT:

The oil on the exhaust pipe may be from the transmission, etc.


C




A

4.CHECK TEMPERATURE WHEN WHITE SMOKE IS EMITTED

B

27.CHECK IDLING CONDITION

C

28.CHECK FOR OIL LEAKAGE
4.CHECK TEMPERATURE WHEN WHITE SMOKE IS EMITTED
a.

Check whether the white smoke is emitted only when the engine coolant temperature is below 0°C (32°F).

HINT:
·

If so, the smoke is not from the turbocharger and may be the smoke of unburned fuel.

·

If misfiring occurs, unburned fuel is emitted.



Result:
Result Proceed to
White smoke is emitted when the temperature is below 0°C (32°F) A
White smoke is emitted regardless of temperature B




A

5.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)

B

6.READ VALUE USING GTS (TARGET FUEL PRESSURE (HIGH) AND FUEL PRESSURE (HIGH))
5.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)

Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (TARGET FUEL PRESSURE (HIGH) AND FUEL PRESSURE (HIGH))

NG

6.READ VALUE USING GTS (TARGET FUEL PRESSURE (HIGH) AND FUEL PRESSURE (HIGH))
a.

Start the engine.


b.

Enter the following menus: Powertrain / Engine / Data List / Target Fuel Pressure (High) and Fuel Pressure (High).

Powertrain > Engine > Data List
Tester Display
Target Fuel Pressure (High)
Fuel Pressure (High)
50003 372 264,265

c.

Take a snapshot with the GTS.


d.

Measure the difference between the target fuel pressure (Target Fuel Pressure (High)) and the actual fuel pressure (Fuel Pressure (High)) when racing the engine with the accelerator pedal fully depressed.

Result:
Result Proceed to
Fuel Pressure (High) is within 3500 kPag of Target Fuel Pressure (High) A
Except above B


HINT:
·

"Target Fuel Pressure (High)" is the target fuel pressure controlled by the ECM.

·

"Fuel Pressure (High)" is the actual fuel pressure.





A

7.READ VALUE USING GTS (INJECTION FEEDBACK VALUE #1 TO #6 AND TARGET INJECTION VOLUME)

B

15.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP ASSEMBLY
7.READ VALUE USING GTS (INJECTION FEEDBACK VALUE #1 TO #6 AND TARGET INJECTION VOLUME)
a.

Check Injection Feedback Value #1 to #6 and Target Injection Volume in the snapshot taken after the engine is warmed up and idled for 1 minute with the A/C off.

HINT:

Engine coolant temperature is 75°C (167°F) or higher.


Result:
Result Proceed to
Injection Feedback Value #1 to #6 are 4.9 mm3/st or less and Target Injection Volume is 2.3 to 10 mm3/st A
Other than above B




A

8.READ VALUE USING GTS (INJECTOR LEAKING COUNT #1 TO #6, I-ART LEARNING STATUS HISTORY #1 TO #6)

B

13.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT CYLINDER FUEL CUT)
8.READ VALUE USING GTS (INJECTOR LEAKING COUNT #1 TO #6, I-ART LEARNING STATUS HISTORY #1 TO #6)
a.

Enter the following menus: Powertrain / Engine / Data List / Injector Leaking Count #1 to #6 and i-ART Learning Status History #1 to #6.


b.

Record the value displayed for Injector Leaking Count #1 to #6 and i-ART Learning Status History #1 to #6.

Result:
Result Proceed to
The value for Injector Leaking Count #1 to #6 does not change from 0
The value for i-ART Learning Status History #1 to #6 does not change from 0
(w/ EGR System)
A
The value for Injector Leaking Count #1 to #6 does not change from 0
The value for i-ART Learning Status History #1 to #6 does not change from 0
(w/o EGR System)
B
The value for Injector Leaking Count #1 to #6 displays 1 or more
The value for i-ART Learning Status History #1 to #6 displays 1 or more
C




A

9.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EGR VALVE CLOSE BANK 1)

B

10.CHECK ENGINE ASSEMBLY

C

11.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
9.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EGR VALVE CLOSE BANK 1)
a.

Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.


b.

Enter the following menus: Powertrain / Engine / Data List / Mass Air Flow Sensor.

Powertrain > Engine > Data List
Tester Display
Mass Air Flow Sensor
50003 372 215

c.

Read the Mass Air Flow Sensor value displayed on the GTS while the engine is idling.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the EGR Valve Close Bank 1 / Data List / Mass Air Flow Sensor.

Powertrain > Engine > Active Test
Active Test Display
Activate the EGR Valve Close Bank 1
Data List Display
Mass Air Flow Sensor
50004 372 71 215

e.

Read the Mass Air Flow Sensor value when the EGR valve is closed using the Active Test function.

HINT:

Before performing the diagnosis, confirm that the EGR valve target opening angle is not 0%.


Result:
Active Test Result Proceed to
Activate the EGR Valve Close Bank 1:
OFF to Closed
Mass Air Flow Sensor value does not change A
Mass Air Flow Sensor value changes B


NOTICE:

As the measured values may differ from those shown below due to factors such as differences in measuring environments and changes in vehicle condition due to aging, do not use these values to determine whether the vehicle is malfunctioning or not.


HINT:

The problem may be a temporary one, due to the entry of deposits or foreign matter. Check that there are no deposits or foreign matter in the electric EGR control valve assembly or mass air flow meter sub-assembly.


Reference:
EGR Valve Condition (Opening) Measuring Condition Mass Air Flow Sensor (Reference)
Open (45%)
·

Atmospheric pressure: 101 kPa

·

Engine coolant temperature: 75°C (167°F)


5 to 14 gm/sec
Closed (0%) 13 to 18 gm/sec




A

REMOVE DEPOSIT (ELECTRIC EGR CONTROL VALVE ASSEMBLY)

B

10.CHECK ENGINE ASSEMBLY
10.CHECK ENGINE ASSEMBLY
a.

Inspect the engine to see whether white smoke is being emitted due to defects in the engine itself.

i.

Check for oil leaking into the combustion chamber due to a faulty valve stem oil seal.


ii.

Check for oil leaking into the combustion chamber due to a faulty injector assembly nozzle sheet.


iii.

Check for low compression.

HINT:

If the engine runs too rough, Injection Feedback Value #1 to #6 cannot be corrected and the readout will (incorrectly) show that Injection Feedback Value #1 to #6 are within the normal range.


HINT:

If defects are found, perform repairs, and then check that the symptoms are no longer present.




Result:
Proceed to
NEXT



NEXT

END

11.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
NOTICE:

Only replace the injector assembly for the cylinder which displays an Injector Leaking Count #1 to #6 value of 1 or more, or i-ART Learning Status History #1 to #6 value of 1 or more.


a.

Replace the injector assembly of the malfunctioning cylinder.

Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL INJECTOR>REMOVAL

NOTICE:
·

Replace the injection pipe sub-assembly that was removed with a new one.

·

Following the repair manual, temporarily install the injection pipe and after positioning the injector, tighten the injector to the specified torque.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

12.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
12.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
a.

Clean the fuel filter case and replace the fuel filter element assembly.

Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL FILTER (for Fuel Tank Side)>REPLACEMENT

HINT:

Be sure to clean the inside of the fuel filter case as the injector assemblies may not operate properly if the fuel filter element assembly is installed with foreign matter remaining inside the fuel filter case.



Result:
Proceed to
NEXT



NEXT

18.BLEED AIR FROM FUEL SYSTEM
13.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT CYLINDER FUEL CUT)
HINT:

Use this Active Test to determine the malfunctioning cylinder.


a.

Start the engine.


b.

Enter the following menus: Powertrain / Engine / Active Test / Control the Select Cylinder Fuel Cut.

Powertrain > Engine > Active Test
Tester Display
Control the Select Cylinder Fuel Cut
50004 372 42026
HINT:

If the engine idle speed does not change when an injector assembly is disabled, the cylinder being tested is malfunctioning. Record any malfunctioning cylinders.



Result:
Proceed to
NEXT



NEXT

14.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)
14.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)
HINT:

Use this Active Test to help determine whether a cylinder has compression loss or not.


a.

Enter the following menus: Powertrain / Engine / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed Cylinder #1 to #6.

Powertrain > Engine > Active Test
Active Test Display
Check the Cylinder Compression
Data List Display
Engine Speed Cylinder #1
Engine Speed Cylinder #2
Engine Speed Cylinder #3
Engine Speed Cylinder #4
Engine Speed Cylinder #5
Engine Speed Cylinder #6
50004 372 42028 493,494,495,496,497,498

b.

Crank the engine.


c.

Check the engine speed during the Active Test.

Result:
Result Proceed to
The values of Engine Speed Cylinder #1 to #6 are within 10 rpm of each other A
Other than above B


HINT:

When cranking, if the speed of a cylinder is approximately 100 rpm more than the other cylinders, there is probably a complete loss of compression in that cylinder.




A

21.READ VALUE USING GTS (INJECTOR LEAKING COUNT #1 TO #6, I-ART LEARNING STATUS HISTORY #1 TO #6)

B

20.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
15.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP ASSEMBLY
a.

Disconnect the inlet hose from the fuel supply pump assembly.


b.

Operate the priming pump and check that fuel is being supplied to the fuel supply pump assembly.

OK:

Fuel is properly supplied to the fuel supply pump assembly when the priming pump is operated.


HINT:
·

A lack of fuel causes the fuel pressure to drop.

·

Check that the fuel filter element assembly is not clogged.




c.

Reconnect the inlet hose.


Result:
Proceed to
NEXT



NEXT

16.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
16.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
a.

Clean the fuel filter case and replace the fuel filter element assembly.

Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL FILTER (for Fuel Tank Side)>REPLACEMENT

HINT:

Be sure to clean the inside of the fuel filter case as the injector assemblies may not operate properly if the fuel filter element assembly is installed with foreign matter remaining inside the fuel filter case.



Result:
Proceed to
NEXT



NEXT

17.CHECK AND REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP ASSEMBLY)
17.CHECK AND REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP ASSEMBLY)
a.

Check and replace the clogged fuel pipe.


Result:
Proceed to
NEXT



NEXT

18.BLEED AIR FROM FUEL SYSTEM
18.BLEED AIR FROM FUEL SYSTEM
HINT:

If the fuel filter element assembly or fuel pipe has been replaced, be sure to remove any air in the system.


a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check whether the white smoke problem has been successfully repaired by starting the engine.


Result:
Proceed to
NEXT



NEXT

END

20.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
HINT:

Measure the compression of the cylinder that had a high speed during the Active Test "Check the Cylinder Compression".



Result:
Proceed to
OK
NG



OK

21.READ VALUE USING GTS (INJECTOR LEAKING COUNT #1 TO #6, I-ART LEARNING STATUS HISTORY #1 TO #6)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

21.READ VALUE USING GTS (INJECTOR LEAKING COUNT #1 TO #6, I-ART LEARNING STATUS HISTORY #1 TO #6)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine / Data List / Injector Leaking Count #1 to #6 and i-ART Learning Status History #1 to #6.


e.

Record the value displayed for Injector Leaking Count #1 to #6 and i-ART Learning Status History #1 to #6.


Result:
Proceed to
NEXT



NEXT

22.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
22.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
NOTICE:
·

Replace the injector assembly of the cylinder which displays a value of 4.9 mm3/st or higher for Injection Feedback Value #1 to #6 in step 7.

·

Only replace the injector assembly for the cylinder which displays an Injector Leaking Count #1 to #6 value of 1 or more, or i-ART Learning Status History #1 to #6 value of 1 or more.

·

If Injector Leaking Count #1 to #6 and i-ART Learning Status History #1 to #6 both display 0, only replace the injector assembly for the cylinder which was determined to be malfunctioning using Injection Feedback Value #1 to #6.



a.

Replace the injector assembly of the malfunctioning cylinder.

Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL INJECTOR>REMOVAL

NOTICE:
·

Replace the injection pipe sub-assembly that was removed with a new one.

·

Following the repair manual, temporarily install the injection pipe and after positioning the injector, tighten the injector to the specified torque.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

23.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
23.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
a.

Clean the fuel filter case and replace the fuel filter element assembly.

Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL FILTER (for Fuel Tank Side)>REPLACEMENT

HINT:

Be sure to clean the inside of the fuel filter case as the injector assemblies may not operate properly if the fuel filter element assembly is installed with foreign matter remaining inside the fuel filter case.



Result:
Proceed to
NEXT



NEXT

24.BLEED AIR FROM FUEL SYSTEM
24.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

25.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
25.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check whether the white smoke problem has been successfully repaired by starting the engine.


Result:
Proceed to
OK
NG



OK

END

NG

26.CHECK FUEL QUALITY
26.CHECK FUEL QUALITY
a.

Check that only diesel fuel is being used.


b.

Check that the fuel does not contain any impurities.


Result:
Proceed to
NEXT



NEXT

END

27.CHECK IDLING CONDITION
a.

Start the engine.


b.

Check the idling condition.

Result:
Result Proceed to
Engine run smoothly at idle, however white smoke is emitted. A
There are problems such as rough idling or engine stall, and white smoke is emitted.
HINT:

If the pressure in the crank case has risen, white smoke will be produced just after the engine is started. In this case, if blow-by gas is ejected when the oil level gauge is slightly removed*, it is possible that the piston is damaged.


NOTICE:

*Do not completely remove the oil level gauge as oil may spray from the opening.


B


HINT:

It is possible to determine the faulty cylinder by carrying out the "Check the Cylinder Compression" Active Test.




A

B

REPAIR ENGINE ASSEMBLY

28.CHECK FOR OIL LEAKAGE
a.

Remove any oil in the front exhaust pipe assembly.

HINT:

Oil in the exhaust pipe is producing white smoke.



b.

If there is an oil leak, repair the leak.


Result:
Proceed to
NEXT



NEXT

END