Home › Engine / Hybrid System › F33A-FTV (ENGINE MECHANICAL) › ENGINE › from 2021.07
RM38G0E _51 Engine / Hybrid System _106330 F33A-FTV ENGINE MECHANICAL _0491793 ENGINE G

F33A-FTV ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:
A345137

To prevent injury due to contact with an operating fan and generator V belt or cooling fan, keep your hands and clothing away from the fan and generator V belt and cooling fans when working in the engine compartment with the engine running or the ignition switch ON.


PROCEDURE

Hide 16620D 5.INSPECT V-RIBBED BELT TENSIONER ASSEMBLY

Hide 88359 6.INSPECT VISCOUS HEATER V BELT (w/ Viscous Heater)

Hide 13750 7.CHECK VALVE LASH ADJUSTER ASSEMBLY

a.

Rev up the engine several times. Check that the engine does not emit unusual noises.

If unusual noises occur, warm up the engine and idle it for over 30 minutes. Then perform the inspection above again.

If any defects or problems are found during the inspection above, perform a valve lash adjuster inspection.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION


Hide 17801 8.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 9.INSPECT ENGINE IDLE SPEED

a.

Warm up and stop the engine.


b.

Connect the GTS to the DLC3.


c.

Start the engine and idle it.


d.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 372 211

e.

Inspect the engine idle speed.

Standard idle speed:

550 to 650 rpm


NOTICE:
·

Turn off all the electrical systems and the A/C.

·

When checking the idle speed, move the shift lever to neutral or park.




f.

Disconnect the GTS from the DLC3.


Hide 10.INSPECT MAXIMUM ENGINE SPEED

a.

Start the engine.


b.

Fully depress the accelerator pedal.


c.

Check the maximum engine speed.

Maximum engine speed:

4650 to 4750 rpm



Hide 11.INSPECT COMPRESSION

a.

Warm up and stop the engine.


b.

Disconnect the cable from the negative (-) battery terminal.


c.

Disconnect all connectors from the 6 fuel injector assemblies.


d.

e.

Connect the cable from the negative (-) battery terminal.


f.

Inspect compression pressure.

i.

Insert a SST (attachment K) into the glow plug hole.

SST
09992-10140  

Torque:
17.5 N*m (178 kgf*cm, 13 ft.*lbf)


ii.

Connect SST (gauge assembly) and SST (packing set) to SST (L-joint).

SST
09992-19015  (09992-10010, 09992-10020, 09992-10030)


iii.

Connect SST (gauge assembly), SST (packing set) and SST (L-joint) to SST (attachment K).


iv.

Depress and hold the brake pedal, and cranking the engine. Then check the compression pressure.

Standard Compression Pressure:

2500 kPa (25.5 kgf/cm2, 363 psi)


Minimum Compression Pressure:

2000 kPa (20.4 kgf/cm2, 290 psi)


Pressure Difference between Each Cylinder:

500 kPa (5.1 kgf/cm2, 73 psi)


NOTICE:
·

Use a fully-charged battery so the engine speed can be increased to 280 rpm or more.

·

Inspect all cylinders in the same way.

·

Measure the compression pressure as quickly as possible.




v.

If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the glow plug holes. Then inspect the cylinder compression again.

If adding oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.

If the pressure stays low, the valve may be stuck or seated improperly, or there may be leakage from the gasket.



g.

Remove the SST.


h.

Disonnect the cable from the negative (-) battery terminal.


i.

Connect all connectors to the 6 fuel injector assemblies.