| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | OUTER MIRROR LH | 87961 | - | - | - |
| 2 | OUTER MIRROR COVER LH | 87945 | ( ) |
- | - |
| 3 | COVER BODY | - | ( ) |
- | - |
| 4 | SIDE TURN SIGNAL LIGHT ASSEMBLY LH | 81740 | - | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 5 | COVER BODY | - | ( ) |
- | - |
| 6 | SIDE TELEVISION CAMERA ASSEMBLY LH | 86790F | - | - | - |
| 7 | OUTER MIRROR LIGHT ASSEMBLY LH | - | - | - | - |
| *A | w/ Foot Light | *B | w/ Panoramic View Monitor System |
| *1 | ACTUATOR SUB-ASSEMBLY | *2 | LOWER COVER BODY |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 8 | OUTER MIRROR RETRACTOR LH | 87966 | ( ) |
- | - |
| 9 | SUPPORT | - | - | - | - |
| *A | w/ Reverse Shift-linked Mirror | *B | w/o Reverse Shift-linked Mirror |
| *1 | BODY | *2 | HOOK |
| *3 | LOWER COVER BASE | *4 | UPPER COVER BASE |
| *5 | CUT LINE SEAL | *6 | FRAME SUB-ASSEMBLY |
| *7 | HARNESS SUB-ASSEMBLY | *8 | VINYL TAPE |
| *9 | GASKET | *10 | BASE SUB-ASSEMBLY |
| ● | Non-reusable part | - | - |
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
87961 1.REMOVE OUTER MIRROR LH
81740 4.REMOVE SIDE TURN SIGNAL LIGHT ASSEMBLY LH
5.REMOVE COVER BODY
| *A | w/ Panoramic View Monitor System | *B | w/ Foot Light |
w/ Panoramic View Monitor System:
1. Detach the clamp.
2. Disconnect the connector.
w/ Foot Light:
1. Detach the clamp.
2. Disconnect the connector.
Disconnect the 2 connectors and detach the guide.
|
Remove in this Direction | - | - |
Remove the 4 screws.
Using a thin-bladed screwdriver, disconnect the connector and remove the actuator sub-assmbly.
Tape the thin-bladed screwdriver tip before use.
Pull the cover body as shown in the illustration to remove it.
86790F 6.REMOVE SIDE TELEVISION CAMERA ASSEMBLY LH (w/ Panoramic View Monitor System)
7.REMOVE OUTER MIRROR LIGHT ASSEMBLY LH (w/ Foot Light)
87966 8.REMOVE OUTER MIRROR RETRACTOR LH
| *A | w/ Panoramic View Monitor System | - | - |
| *1 | Harness Sub-assembly | *2 | Television Camera Wire |
| *3 | Hook | - | - |
| *a | Cut here | - | - |
Cut the harness sub-assembly and the television camera wire at the location shown in the illustration.
Remove the screw.
Detach the guide and remove the hook.
|
Remove in this Direction | - | - |
Detach the guide and fold back the gasket as shown in the illustration.
Using a screwdriver, detach the claw and remove the lower cover base as shown in the illustration.
Tape the screwdriver tip before use.
|
Remove in this Direction | - | - |
Using a T25 "TORX" socket wrench, remove the 3 "TORX" screws and base sub-assembly.
Using a thin-bladed screwdriver, detach the claw and guide.
Tape the thin-bladed screwdriver tip before use.
Remove the upper cover base.
Remove the cut line seal.
|
Remove in this Direction | - | - |
Remove the 2 screws.
Detach the guide to remove the frame sub-assembly together with the harness sub-assembly as shown in the illustration.
Remove the harness sub-assembly.
9.REMOVE SUPPORT
|
Remove in this Direction | - | - |