If an open or short circuit in the roof antenna assembly is detected as a result of a terminal check performed by the telephone transceiver assembly, these DTCs will be stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B15CB11 | Telephone Main Antenna Circuit Short to Ground | Roof antenna assembly impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON (Short circuit) |
·
Telephone transceiver Assembly
·
Roof antenna assembly
·
No. 3 antenna cord sub-assembly
·
Antenna cord sub-assembly |
Telematics | A |
| B15CB13 | Telephone Main Antenna Circuit Open | Roof antenna assembly impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON (Open circuit) |
·
Telephone transceiver Assembly
·
Roof antenna assembly
·
No. 3 antenna cord sub-assembly
·
Antenna cord sub-assembly |
Telematics | A |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (w/o Emergency Call Service)>PRECAUTION
When replacing the telephone transceiver assembly, make sure to replace it with a new one.
Pre-procedure1
Turn the ignition switch to ON and wait for 10 seconds or more.
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
None
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Pre-procedure1
| *a | Component without harness connected (Roof Antenna Assembly) |
Remove the roof antenna assembly.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 - 4a | Always | 9 to 11 kΩ |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
| *a | Front view of wire harness connector (to Roof Antenna Assembly) |
| *b | Front view of wire harness connector (to Antenna Cord Sub-assembly) |
Disconnect the antenna connector from the roof antenna assembly connector.
Disconnect the antenna connector from the antenna cord sub-assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-4 - B-3 | Always | Below 1 Ω |
| A-4a - B-3a | Always | Below 1 Ω |
| A-4 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Pre-procedure1
| *a | Front view of wire harness connector (to No. 3 Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector (to Telephone Transceiver Assembly) |
Disconnect the antenna connector from the No. 3 antenna cord sub-assembly connector.
Disconnect the antenna connector from the telephone transceiver assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-3 - C-1 (ANT1) | Always | Below 1 Ω |
| B-3a - C-1a | Always | Below 1 Ω |
| B-3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD (for Instrument Panel)>REMOVAL
Replace the telephone transceiver assembly with a new one.
| Proceed to |
|---|
| NEXT |
NEXT
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (w/o Emergency Call Service)>REGISTRATION