1.DRAIN ENGINE OIL
27020 2.REMOVE GENERATOR ASSEMBLY
16400 3.REMOVE RADIATOR ASSEMBLY
17875 4.REMOVE INTAKE AIR CONNECTOR PIPE
5.REMOVE MANUAL TRANSMISSION WITH TRANSFER
31210 6.REMOVE CLUTCH COVER ASSEMBLY
31250 7.REMOVE CLUTCH DISC ASSEMBLY
13405 8.REMOVE FLYWHEEL SUB-ASSEMBLY
12142 9.REMOVE NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE
11452 10.REMOVE NO. 1 ENGINE OIL LEVEL DIPSTICK GUIDE
Disconnect the connector clamp.
Remove the 2 bolts and No. 1 engine oil level dipstick guide from the oil pan sub-assembly and transverse engine mounting bracket RH.
Remove the O-ring from the No. 1 engine oil level dipstick guide.
17878A 11.REMOVE NO. 3 INTAKE AIR CONNECTOR PIPE
Loosen the hose clamp bolt.
Remove the bolt and No. 3 intake air connector pipe from the oil pan sub-assembly.
15778 12.DISCONNECT NO. 2 OIL COOLER HOSE
Slide the clamp and remove the bolt and hose bracket from the V-ribbed belt tensioner assembly.
Disconnect the No. 2 oil cooler hose from the oil pan sub-assembly.
16603B 13.REMOVE IDLER PULLEY SUB-ASSEMBLY
Remove the bolt and idler pulley sub-assembly from the V-ribbed belt tensioner assembly.
16620D 14.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
Remove the 5 bolts and V-ribbed belt tensioner assembly from the oil pan sub-assembly and timing chain cover sub-assembly.
15.DISCONNECT ENGINE WIRE
Disconnect the crankshaft position sensor connector and connector clamp.
w/ Oil Pressure Gauge:
Disconnect the oil pressure sender gauge assembly connector.
w/o Oil Pressure Gauge:
Disconnect the engine oil pressure switch assembly connector.
Disconnect the 3 engine wire connector clamps.
15769 16.DISCONNECT OIL COOLER PIPE
Remove the 3 bolts and disconnect the oil cooler pipe.
Remove the gasket from the oil cooler pipe.
15407 17.DISCONNECT INLET TURBO OIL PIPE SUB-ASSEMBLY
Remove the union bolt and gasket.
Remove the bolt, No. 2 intake air connector bracket and disconnect the inlet turbo oil pipe sub-assembly from the oil pan sub-assembly.
83520 18.REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY (w/ Oil Pressure Gauge)
83530 19.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY (w/o Oil Pressure Gauge)
20.REMOVE ENGINE WIRE BRACKET
Remove the 2 bolts and engine wire bracket from the cylinder block and oil pan sub-assembly.
15474A 21.REMOVE OUTLET TURBO OIL HOSE
Slide the 2 clamps and remove the outlet turbo oil hose.
25708 22.DISCONNECT NO. 3 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY
| *1 | Vacuum Transmitting Hose |
| *2 | No. 3 Vacuum Transmitting Pipe Sub-assembly |
Remove the vacuum transmitting hose from the No. 3 vacuum transmitting pipe sub-assembly and turbocharger.
Remove the bolt and disconnect the No. 3 vacuum transmitting pipe sub-assembly from the oil pan sub-assembly.
12201 23.REMOVE VENTILATION TUBE SUB-ASSEMBLY
Remove the union bolt and gasket, and disconnect the ventilation tube sub-assembly from the oil pan sub-assembly.
17293 24.REMOVE TURBOCHARGER STAY
Remove the 2 bolts and turbocharger stay from the turbocharger and oil pan sub-assembly.
12102A 25.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
| *a | Nut |
Remove the 16 bolts and 2 nuts.
Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly from the oil pan sub-assembly.
Be careful not to damage the contact surfaces of the oil pan sub-assembly and No. 2 oil pan sub-assembly.
15614 26.REMOVE LOWER OIL FILTER ELEMENT COVER
Remove the 4 bolts and lower oil filter element cover from the oil pan sub-assembly.
27.REMOVE OIL FILTER ELEMENT
12101 28.REMOVE OIL PAN SUB-ASSEMBLY
| *1 | Seal Washer |
| *a | Nut |
Remove the 20 bolts, 2 nuts and seal washer.
Be sure to clean the bolts and stud bolts, and check the threads for cracks or other damage.
| *A | for RH Side |
| *B | for LH Side |
| *a | Protective Tape |
Remove the oil pan sub-assembly by prying between the oil pan sub-assembly and cylinder block with a screwdriver.
Be careful not to damage the contact surfaces of the cylinder block and oil pan sub-assembly.
Tape the screwdriver tip before use.
Remove the O-ring from the oil regulator assembly.
Remove the 2 O-rings from the scavenging pump assembly.
Remove the cylinder block oil hole gasket from the cylinder block.
15403 29.REMOVE OUTLET OIL PUMP PIPE SUB-ASSEMBLY
Remove the 4 bolts, outlet oil pump pipe sub-assembly and O-ring from the oil pan sub-assembly.
15104 30.REMOVE OIL STRAINER SUB-ASSEMBLY
Remove the 3 bolts, oil strainer sub-assembly and O-ring from the cylinder block.
15310H 31.REMOVE OIL REGULATOR ASSEMBLY
Remove the 4 bolts and oil regulator assembly from the oil pump assembly.
11381 32.REMOVE REAR ENGINE OIL SEAL RETAINER
| *a | Protective Tape |
Remove the 10 bolts.
Remove the rear engine oil seal retainer by prying between the rear engine oil seal retainer and cylinder block with a screwdriver.
Be careful not to damage the contact surfaces of the rear engine oil seal retainer and cylinder block.
Tape the screwdriver tip before use.
15100 33.REMOVE OIL PUMP ASSEMBLY
Remove the 4 bolts and oil pump assembly.