Home › Engine / Hybrid System › 1VD-FTV (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2014.08–2016.08
RM25T0E _51 Engine / Hybrid System _029207 1VD-FTV ENGINE MECHANICAL _0132955 ENGINE ASSEMBLY A

1VD-FTV ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 53301 3.REMOVE HOOD SUB-ASSEMBLY

a.

Disconnect the washer hose.


b.

Remove the 4 bolts and hood sub-assembly.


Hide 16400 4.REMOVE RADIATOR ASSEMBLY

Hide 87246A 7.DISCONNECT HEATER WATER HOSE

a.
A163847C01
0.365,0.167 1.365,0.167 true 1.833,0.333 2.25,0.667 2.25,0.667 2.417,0.667 true 0.208,0.073 0.417,0.271 0.208,0.198 10 false *1 2.438,0.583 2.844,0.854 0.406,0.271 10 true *2
*1 Inlet Heater Water Hose
*2 Outlet Heater Water Hose


Slide the clamp and disconnect the inlet heater water hose from the outlet heater water pipe B.


b.

Slide the clamp and disconnect the outlet heater water hose from the outlet heater water pipe B.


Hide 28800 9.REMOVE BATTERY

a.

Remove the bolt, nut, battery clamp and battery.


Hide 74403A 10.REMOVE BATTERY CARRIER SUB-ASSEMBLY

a.
A316775

Remove the bolt.


b.

Detach the clamp and disconnect the No. 2 fuse block from the battery carrier sub-assembly.


c.

Remove the fusible link block cover.


d.
A316776

Remove the bolt and disconnect the engine wire.


e.

Detach the wire harness clamp.


f.

Remove the 2 bolts.


g.

Detach the clamp and disconnect the fusible link block from the battery carrier sub-assembly.


h.
A316777

Detach the 3 wire harness clamps.


i.

Remove the 5 bolts and battery carrier sub-assembly.


Hide 44310 11.DISCONNECT VANE PUMP ASSEMBLY

a.
A328671

Disconnect the power steering oil pressure switch connector.


b.

Remove the 2 nuts and disconnect the vane pump assembly.

HINT:

It is not necessary to completely remove the vane pump assembly. With the hoses connected to the vane pump assembly, hang the vane pump assembly on the vehicle body with a rope.



c.

Remove the O-ring from the vane pump assembly.


Hide 88320 12.DISCONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

a.

Disconnect the cooler compressor assembly connector.


b.
A163880

Remove the 4 bolts and disconnect the cooler compressor assembly.

HINT:

It is not necessary to completely remove the cooler compressor assembly. With the hoses connected to the cooler compressor assembly, hang the cooler compressor assembly on the vehicle body with a rope.



Hide 44778 13.DISCONNECT CONNECTOR TO CHECK VALVE HOSE

a.
A163855

Slide the clamp and disconnect the connector to check valve hose from the cylinder head cover sub-assembly.


Hide 23271H 14.DISCONNECT NO. 1 AND NO. 2 FUEL HOSES

a.
A163848C01
1.969,1.333 2.25,0.417 2.25,0.417 2.417,0.417 true 2.167,1.583 2.365,0.917 2.365,0.917 2.531,0.917 true 2.552,0.823 2.896,1.052 0.344,0.229 10 true *1 2.427,0.323 2.729,0.573 0.302,0.25 10 true *2
*1 No. 1 Fuel Hose
*2 No. 2 Fuel Hose


Slide the clamp and disconnect the No. 1 fuel hose from the fuel filter cap assembly.


b.

Slide the clamp and disconnect the No. 2 fuel hose from the fuel pipe.


Hide 82111 15.DISCONNECT ENGINE ROOM MAIN WIRE

a.

Disconnect the ECM connector.


b.

Using a clip remover, detach the 2 engine room main wire clamps.


c.

Disconnect the 4 engine room main wire connectors.


d.

Disconnect the 4 injector driver connectors.


e.

Using a clip remover, detach the 2 engine room main wire clamps.

A316778


Hide 87249B 16.DISCONNECT HEATER WATER OUTLET PIPE B

Hide 17940D 18.REMOVE INTERCOOLER ASSEMBLY

Hide 82111 23.DISCONNECT ENGINE ROOM MAIN WIRE

a.

Detach the 12 engine room main wire harness clamps.


b.

Disconnect the 20 connectors.


c.

Remove the 19 bolts.


d.

Remove the terminal cap and nut, and disconnect the generator wire.

A316779


Hide 26100G 24.REMOVE DIESEL THROTTLE BODY ASSEMBLY (for Bank 1)

Hide 26100G 25.REMOVE DIESEL THROTTLE BODY ASSEMBLY (for Bank 2)

Hide 17947B 27.REMOVE NO. 3 INTERCOOLER SUPPORT BRACKET

Hide 16264 28.DISCONNECT NO. 2 AND NO. 3 WATER BY-PASS HOSES

Hide 23804D 30.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY

Hide 44769 31.REMOVE VACUUM RESERVOIR CONNECT TUBE

Hide 44761 33.REMOVE VACUUM PUMP TO CONNECTOR TUBE

Hide 25850 35.REMOVE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY

Hide 23701 38.REMOVE INJECTION PIPE SUB-ASSEMBLY RH

Hide 23702 39.REMOVE INJECTION PIPE SUB-ASSEMBLY LH

Hide 23706 40.REMOVE NO. 6 INJECTION PIPE SUB-ASSEMBLY

Hide 23239D 41.REMOVE NO. 1 FUEL HOSE

Hide 23805B 42.REMOVE NO. 5 FUEL PIPE SUB-ASSEMBLY

Hide 23705 43.REMOVE NO. 5 INJECTION PIPE SUB-ASSEMBLY

Hide 23810A 44.REMOVE COMMON RAIL ASSEMBLY RH

Hide 23820A 45.REMOVE COMMON RAIL ASSEMBLY LH

Hide 23801L 46.REMOVE FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY

Hide 16289 50.DISCONNECT NO. 5 WATER BY-PASS PIPE

Hide 25601 51.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 25602 52.REMOVE NO. 2 EGR PIPE SUB-ASSEMBLY

Hide 25620 53.REMOVE EGR VALVE ASSEMBLY WITH EGR COOLER ASSEMBLY

Hide 23763 54.DISCONNECT NO. 3 NOZZLE LEAKAGE PIPE

a.
A168390

Remove the union bolt and gasket.


b.

Remove the bolt and disconnect the No. 3 nozzle leakage pipe.


Hide 55.REMOVE STARTER HOSE BRACKET SUB-ASSEMBLY

a.
A287055

Disconnect the 2 starter hoses from the starter assembly and starter hose bracket sub-assembly.


b.
A272101

Remove the 2 bolts and starter hose bracket sub-assembly.


Hide 19871 56.REMOVE NO. 1 GLOW PLUG CONNECTOR

Hide 82112 57.REMOVE NO. 2 ENGINE ROOM WIRE

a.
A328672

Disconnect the starter assembly connector.


b.

Remove the nut and disconnect the starter assembly wire harness.


c.

Detach the No. 2 engine room wire clamp.


d.

Remove the bolt and No. 2 engine room wire.


Hide 37140 58.REMOVE FRONT PROPELLER SHAFT ASSEMBLY

Hide 37110 59.REMOVE REAR PROPELLER SHAFT ASSEMBLY

Hide 12281A 61.INSTALL ENGINE HANGER

a.

Install the No. 1 and No. 2 engine hangers with the 4 bolts shown in the illustration.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)

HINT:
Part No.
No. 1 Engine Hanger 12281-51040
No. 2 Engine Hanger 12282-51040
Bolt 91671-80825


A316809C01
5.333,0.833 5.75,0.5 5.75,0.5 5.917,0.5 true 5.083,2.25 5.667,1.75 5.667,1.75 5.833,1.75 true 3.823,0.448 4.135,0.604 0.313,0.156 10 false *A 3.823,1.781 4.135,1.938 0.313,0.156 10 false *B 5.948,0.417 6.26,0.573 0.313,0.156 10 false *1 5.865,1.656 6.177,1.813 0.313,0.156 10 false *2
*A for Bank 1 *B for Bank 2
*1 No. 1 Engine Hanger *2 No. 2 Engine Hanger



Hide 62.REMOVE ENGINE ASSEMBLY

a.

Attach an engine sling device and hang the engine with a chain block.


b.
A163874C01
0.177,0.281 0.583,0.531 0.406,0.25 10 true *A 1.844,0.281 2.25,0.531 0.406,0.25 10 true *B
*A for Bank 1
*B for Bank 2


Remove the 2 nuts and 2 plate washers from the front engine mounting insulator LH and RH.


c.

Lift the engine assembly out of the vehicle carefully.

NOTICE:

Make sure the engine assembly is clear of all wiring and hoses.



d.

Place the engine assembly onto a working bench.


Hide 31210 63.REMOVE CLUTCH COVER ASSEMBLY

Hide 31250 64.REMOVE CLUTCH DISC ASSEMBLY

Hide 33311W 65.INSPECT INPUT SHAFT BEARING

Hide 33311W 66.REPLACE INPUT SHAFT BEARING

Hide 13405 67.REMOVE FLYWHEEL SUB-ASSEMBLY

a.
A163869C01
0.5,4.333 0.5,3.792 true 0.75,2.125 0.75,1.583 true 1.25,3 1.917,3 true 1.958,4.146 1.958,3.604 true 1.104,2.906 1.417,3.063 0.313,0.156 10 false *1 1.875,4.125 2.188,4.281 0.313,0.156 10 false *a 0.615,2.135 1.073,2.333 0.458,0.198 10 false SST 0.365,4.344 0.823,4.542 0.458,0.198 10 false SST
*1 Crankshaft Pulley
*a Protective Tape


Using SST, hold the crankshaft pulley.

SST
09960-10010  (09962-01000, 09963-01000)

NOTICE:

To prevent damage to the crankshaft pulley, apply protective tape to the contact areas of SST and the crankshaft pulley before performing this procedure.



b.
A163846

Remove the 8 bolts and flywheel sub-assembly.


Hide 68.INSTALL ENGINE ASSEMBLY ON ENGINE STAND

a.

Install the engine assembly onto an engine stand with the bolts.


Hide 12281A 69.REMOVE ENGINE HANGER

a.

Remove the 4 bolts and No. 1 and No. 2 engine hangers.


Hide 12361 70.REMOVE FRONT ENGINE MOUNTING INSULATOR RH

a.
A167781C01
0.25,0.063 0.583,0.302 0.333,0.24 10 false *A 1.99,0.063 2.302,0.219 0.313,0.156 10 false *B
*A for Bank 1
*B for Bank 2


Remove the nut, front engine mounting insulator RH and engine mounting stabilizer.


Hide 12361 71.REMOVE FRONT ENGINE MOUNTING INSULATOR LH

a.

Remove the nut, front engine mounting insulator LH and engine mounting stabilizer.


Hide 12371 72.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

a.
A167784

Remove the 4 bolts and rear No. 1 engine mounting insulator from the manual transmission with transfer.