Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2014.08–2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0135360 ECD SYSTEM C

1VD-FTV ENGINE CONTROL  ECD SYSTEM  P0088  Fuel Rail / System Pressure - Too High  P1229  Fuel Pump System  


DESCRIPTION

Refer to the System Description.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>SYSTEM DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0088 Fuel Rail / System Pressure - Too High Fuel pressure of common rail is too high:
Fuel pressure exceeds 230 MPa (2345 kgf/cm2, 33358 psi)
(1 trip detection logic)
·

Fuel supply pump (suction control valve)

·

Common rail LH (pressure limiter)

·

Open or short in fuel supply pump (suction control valve) circuit

·

Fuel temperature sensor, suction control valve wire

·

ECM


Comes on DTC stored
P1229 Fuel Pump System Fuel over-feed:
Fuel pressure is beyond the target fuel pressure despite ECM closing suction control valve
(1 trip detection logic)
·

Short in fuel supply pump (suction control valve) circuit

·

Fuel supply pump (suction control valve)

·

Fuel temperature sensor, suction control valve wire

·

ECM


Comes on DTC stored

HINT:
·

For more information on the fuel supply pump (suction control valve) and common rail system, refer to the system description.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>SYSTEM DESCRIPTION

·

When DTC P0088 and/or P1229 is set, check the internal fuel pressure of the common rail by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Fuel Press.


Reference
Engine Speed Fuel Pressure
Idling Approximately 27000 to 37000 kPa
2500 rpm (No engine load) Approximately 50000 to 70000 kPa


MONITOR DESCRIPTION

P0088 (Internal fuel pressure too high):

The ECM sets this DTC if the fuel pressure inside the common rail is more than 230 MPa (2345 kgf/cm2, 33350 psi). This DTC indicates that: 1) the suction control valve may be stuck open, or 2) there may be a short in the suction control valve circuit.

If this DTC is set, the ECM enters fail-safe mode and limits the engine power. The fail-safe mode continues until the ignition switch is turned OFF.


P1229 (Fuel over-feed):

The ECM sets this DTC if the actual fuel pressure inside the common rail remains higher than the target fuel pressure, despite the ECM closing the suction control valve. This DTC indicates that the suction control valve may be stuck open, or there may be a short in its circuit.

If this DTC is set, the ECM enters fail-safe mode and limits the engine power. The fail-safe mode continues until the ignition switch is turned OFF.


WIRING DIAGRAM

A165726E03
6.083,1.813 6.385,1.969 0.302,0.156 10 false C39 6.083,1.969 6.479,2.156 0.396,0.188 10 false ECM 0.625,1.823 0.927,1.979 0.302,0.156 10 false r2 0.625,1.979 2.25,2.344 1.625,0.365 10 false Fuel Temperature Sensor, Suction Control Valve 1.802,0.74 2.01,0.906 0.208,0.167 10 false +B 2.073,0.729 2.229,0.896 0.156,0.167 10 false 1 1.677,1.406 2,1.573 0.323,0.167 10 false PCV 5.354,0.729 5.604,0.896 0.25,0.167 10 false 106 5.354,1.396 5.635,1.563 0.281,0.167 10 false 105 5.698,1.292 6.083,1.458 0.385,0.167 10 false PCV- 5.698,0.625 6.125,0.781 0.427,0.156 10 false PCV+ 2.073,1.396 2.229,1.563 0.156,0.167 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the fuel supply pump, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0088 AND/OR P1229)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 61
Result:
Result Proceed to
P0088 and/or P1229 are output A
P0190, P0192 and/or P0193 are output B




A

2.INSPECT FUEL SUPPLY PUMP (SUCTION CONTROL VALVE)

B

2.INSPECT FUEL SUPPLY PUMP (SUCTION CONTROL VALVE)
a.
A168115C02
1.448,1.427 1.927,1.729 0.479,0.302 1.885,2.271 2.5,2.052 true 1.552,2.281 0.938,2.052 true 0.135,0.073 0.427,0.344 0.292,0.271 10 false *a 1.573,1.5 1.865,1.667 0.292,0.167 10 false rC1 0.531,1.969 0.875,2.167 0.344,0.198 10 false PCV 2.563,1.969 2.802,2.135 0.24,0.167 10 false +B
*a Component without harness connected
(Fuel Temperature Sensor, Suction Control Valve)


Disconnect the rC1 fuel temperature sensor, suction control valve connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
rC1-2 (+B) - rC1-1 (PCV) 20°C (68°F) 1.9 to 2.3 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK IF DTC OUTPUT RECURS (DTC P1229)

NG

7.CHECK FUEL TEMPERATURE SENSOR, SUCTION CONTROL VALVE WIRE
3.CHECK IF DTC OUTPUT RECURS (DTC P1229)

b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch ON and turn the GTS on.


d.

Disconnect the suction control valve connector and then start the engine. Wait for 1 minute.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 61
Result:
Result Proceed to
No output or engine does not start A
P1229 is output B




A

4.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR, SUCTION CONTROL VALVE CONNECTOR - ECM)

B

4.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR, SUCTION CONTROL VALVE CONNECTOR - ECM)
a.
A311457C05
1.531,0.417 1.948,0.667 0.417,0.25 1.25,2.333 1.667,2.583 0.417,0.25 1.083,1.021 1.521,1.188 true 2.313,1.042 1.938,1.208 true 2.385,4.208 2.188,3.698 true 1.844,4.198 2.094,3.698 true 0.167,0.104 0.479,0.26 0.313,0.156 10 false *a 0.167,2.135 0.479,2.292 0.313,0.156 10 false *b 1.625,0.458 1.875,0.646 0.25,0.188 10 false rC1 1.333,2.375 1.646,2.531 0.313,0.156 10 false C39 0.833,0.927 1.146,1.083 0.313,0.156 10 false +B 2.385,0.948 2.698,1.104 0.313,0.156 10 false PCV 1.438,4.219 2.188,4.427 0.75,0.208 10 false 105 (PCV-) 2.281,4.229 3.146,4.438 0.865,0.208 10 false 106 (PCV+)
*a Front view of wire harness connector
(to Fuel Temperature Sensor, Suction Control Valve)
*b Front view of wire harness connector
(to ECM)


Disconnect the rC1 fuel temperature sensor, suction control valve connector.


b.

Disconnect the C39 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
rC1-1 (PCV) - C39-105 (PCV-) Always Below 1 Ω
rC1-2 (+B) - C39-106 (PCV+) Always Below 1 Ω
rC1-1 (PCV) or C39-105 (PCV-) - Body ground Always 10 kΩ or higher
rC1-2 (+B) or C39-106 (PCV+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE COMMON RAIL LH (PRESSURE LIMITER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE COMMON RAIL LH (PRESSURE LIMITER)

Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS
6.CHECK WHETHER DTC OUTPUT RECURS

b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch ON and turn the GTS on.


d.

Start the engine and drive the vehicle for approximately 15 minutes.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 61

Result:
Result Proceed to
P0088 and/or P1229 are output A
No DTC is output B



A

B

END

7.CHECK FUEL TEMPERATURE SENSOR, SUCTION CONTROL VALVE WIRE
a.
A311458C03
0.573,0.781 0.948,1 0.375,0.219 0.948,3.51 1.323,3.729 0.375,0.219 1.292,3.25 1.74,3.479 true 2.521,3.25 2.115,3.49 true 1.323,1 1.021,1.354 true 1.563,1.01 1.865,1.333 true 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a 0.708,0.813 0.906,0.969 0.198,0.156 10 false r2 1.042,3.542 1.323,3.719 0.281,0.177 10 false rC1 0.979,3.156 1.292,3.354 0.313,0.198 10 false PCV 2.563,3.156 2.875,3.354 0.313,0.198 10 false +B 0.906,1.385 1.219,1.583 0.313,0.198 10 false +B 1.719,1.385 2.031,1.583 0.313,0.198 10 false PCV
*a Component without harness connected
(Fuel Temperature Sensor, Suction Control Valve)


Remove the fuel temperature sensor, suction control valve wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
r2-1 (+B) - rC1-2 (+B) Always Below 1 Ω
r2-2 (PCV) - rC1-1 (PCV) Always Below 1 Ω
r2-1 (+B) or rC1-2 (+B) - Body ground Always 10 kΩ or higher
r2-2 (PCV) or rC1-1 (PCV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE REPLACE FUEL TEMPERATURE SENSOR, SUCTION CONTROL VALVE WIRE