Home › Engine / Hybrid System › 1VD-FTV (FUEL) › FUEL INJECTOR (w/o DPF) › 2014.08–2022.09
RM25T0E _51 Engine / Hybrid System _029770 1VD-FTV FUEL _0135395 FUEL INJECTOR(w/o DPF) A

1VD-FTV FUEL  FUEL INJECTOR(w/o DPF)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL FUEL INJECTOR LH

NOTICE:

Be sure to install the fuel injector LH, nozzle holder clamp and bolt in their original positions.


a.
A164163

Install 4 new injection nozzle seats to the cylinder head sub-assembly LH.


b.
A164164C01
1.823,1.365 1.823,1.75 false 1.729,1.771 1.958,1.948 0.229,0.177 10 false *a
*a New O-Ring


Apply a light coat of clean engine oil to 4 new O-rings.


c.

Install the O-ring to each fuel injector LH as shown in the illustration.


d.

Insert the 4 fuel injector LH into the cylinder head sub-assembly LH.

NOTICE:
·

Insert the fuel injector LH until it touches the injection nozzle seat surface.

·

After installing the fuel injector LH to the cylinder head, the O-ring may prevent the fuel injector LH from fully seating. If so, pull out the fuel injector LH and reinstall it.

·

Always install a fuel injector LH to the same place it was removed from.




e.

For a fuel injector LH that has been replaced with a new fuel injector LH, register the injector compensation code.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION


f.
A164160C01
1.188,3.719 2.177,3.719 false 1.688,3.719 1.688,4.031 false 1.188,3.531 1.188,3.719 1.188,3.719 2.177,3.719 false 2.177,3.719 2.177,3.531 false 1.688,3.719 1.688,4.219 false 0.427,0.469 0.573,0.469 0.573,0.469 0.677,0.875 false 0.219,0.375 0.438,0.552 0.219,0.177 10 false *1 1.625,4.25 1.813,4.458 0.188,0.208 10 false *2 0.604,1.344 0.823,1.521 0.219,0.177 10 false *a
*1 Washer
*2 Nozzle Holder Clamp
*a Downward


Temporarily install 4 new washers and the 4 nozzle holder clamps with the 4 clamp bolts as shown in the illustration.

NOTICE:
·

The fork portion of the nozzle holder clamp must be set on the fuel injector LH.

·

Before tightening the bolts, check that the nozzle holder clamp is set properly.

·

To fasten the clamp bolts, first tighten them by hand until they cannot be turned further. Then, tighten the bolts to the specified torque in a later step.

·

When tightening the bolts, pay attention not to tilt the bolt and nozzle holder clamp.

·

Do not reuse the washer.




g.
A163353

Temporarily install the common rail LH with the 2 bolts.


h.
A168840

Temporarily install the 4 fuel injection pipe LH to the common rail LH and fuel injector LH.


i.
A062123C01
0.896,1.073 0.896,1.552 false 0.823,1.583 1.073,1.781 0.25,0.198 10 false *1
*1 No. 2 Nozzle Leakage Pipe


Check the No. 2 nozzle leakage pipe. Check that there are no scratches or dents on the 5 union seal surfaces. If scratches or dents are present, replace the No. 2 nozzle leakage pipe.


j.

Set the No. 2 nozzle leakage pipe and 5 new gaskets in place.


k.

Temporarily install the No. 2 nozzle leakage pipe with the 4 hollow screws and union bolt.

HINT:

To position the fuel injector LH, loosely tighten the 4 hollow screws and union bolt.



l.

Tighten the 4 nozzle holder clamp bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


m.

Remove the 4 fuel injection pipe LH.


n.

Remove the 2 bolts and common rail LH.


o.
A165056

Tighten the 4 hollow screws.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

NOTICE:
·

If a hollow screw is accidentally tightened beyond the torque specification, it must be replaced.

·

If the No. 2 nozzle leakage pipe is accidentally tightened beyond the torque specification, it must be replaced.




p.
A165057

Tighten the union bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:
·

If the union bolt is accidentally tightened beyond the torque specification, it must be replaced.

·

If the No. 2 nozzle leakage pipe is accidentally tightened beyond the torque specification, it must be replaced.




Hide 2.INSTALL FUEL INJECTOR RH

NOTICE:

Be sure to install the fuel injector RH, nozzle holder clamp and bolt in their original positions.


a.
A164163

Install 4 new injection nozzle seats to the cylinder head sub-assembly RH.


b.
A164164C01
1.823,1.365 1.823,1.75 false 1.729,1.771 1.958,1.948 0.229,0.177 10 false *a
*a New O-Ring


Apply a light coat of clean engine oil to 4 new O-rings.


c.

Install the O-ring to each fuel injector RH as shown in the illustration.


d.

Insert the 4 fuel injector RH into the cylinder head sub-assembly RH.

NOTICE:
·

Insert the fuel injector RH until it touches the injection nozzle seat surface.

·

After installing the fuel injector RH to the cylinder head, the O-ring may prevent the fuel injector RH from fully seating. If so, pull out the fuel injector RH and reinstall it.

·

Always install a fuel injector RH to the same place it was removed from.




e.

For a fuel injector RH that has been replaced with a new fuel injector, register the injector compensation code.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION


f.
A164160C01
1.188,3.719 2.177,3.719 false 1.688,3.719 1.688,4.031 false 1.188,3.531 1.188,3.719 1.188,3.719 2.177,3.719 false 2.177,3.719 2.177,3.531 false 1.688,3.719 1.688,4.219 false 0.427,0.469 0.573,0.469 0.573,0.469 0.677,0.875 false 0.219,0.375 0.438,0.552 0.219,0.177 10 false *1 1.625,4.25 1.813,4.458 0.188,0.208 10 false *2 0.604,1.344 0.823,1.521 0.219,0.177 10 false *a
*1 Washer
*2 Nozzle Holder Clamp
*a Downward


Temporarily install 4 new washers and the 4 nozzle holder clamps with the 4 clamp bolts as shown in the illustration.

NOTICE:
·

The fork portion of the nozzle holder clamp must be set on the fuel injector RH.

·

Before tightening the bolts, check that the nozzle holder clamp is set properly.

·

To fasten the clamp bolts, first tighten them by hand until they cannot be turned further. Then, tighten the bolts to the specified torque in a later step.

·

When tightening the bolts, pay attention not to tilt the bolt and nozzle holder clamp.

·

Do not reuse the washer.




g.
A168839

Temporarily install the 4 fuel injection pipe RH to the common rail RH and fuel injector RH.


h.
A062123C01
0.896,1.073 0.896,1.552 false 0.823,1.583 1.073,1.781 0.25,0.198 10 false *1
*1 Nozzle Leakage Pipe


Check the nozzle leakage pipe. Check that there are no scratches or dents on the 5 union seal surfaces. If scratches or dents are present, replace the nozzle leakage pipe.


i.

Set the nozzle leakage pipe and 5 new gaskets in place.


j.

Temporarily install the nozzle leakage pipe with the 4 hollow screws and union bolt.

HINT:

To position the fuel injector RH, loosely tighten the 4 hollow screws and union bolt.



k.

Tighten the 4 nozzle holder clamp bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


l.

Remove the 4 fuel injection pipe RH.


m.
A165023

Tighten the 4 hollow screws.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

NOTICE:
·

If a hollow screw is accidentally tightened beyond the torque specification, it must be replaced.

·

If the nozzle leakage pipe is accidentally tightened beyond the torque specification, it must be replaced.




n.
A165024

Tighten the union bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:
·

If the union bolt is accidentally tightened beyond the torque specification, it must be replaced.

·

If the nozzle leakage pipe is accidentally tightened beyond the torque specification, it must be replaced.




Hide 11201 3.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH

a.
A164158C01
2.281,0.031 2.479,0.198 0.198,0.167 10 true *a 3.24,0.375 3.417,0.531 0.177,0.156 10 false *a 3.188,1.26 3.396,1.448 0.208,0.188 10 true *a 2.344,1.385 2.552,1.573 0.208,0.188 10 true *a
*a Seal Packing


Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover sub-assembly RH within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

·

Do not start the engine for at least 2 hours after the installation.




b.

Install a new gasket to the cylinder head cover sub-assembly RH.

NOTICE:

Remove any oil from the contact surface.



c.
A164161N01
1.833,0.333 2.167,0.5 0.333,0.167 10 true 1, 11 1.771,1.99 2.125,2.156 0.354,0.167 10 true 2, 20 1.063,0.333 1.198,0.5 0.135,0.167 10 true 9 1.521,2 1.646,2.146 0.125,0.146 10 true 3 0.052,0.521 0.188,0.688 0.135,0.167 10 false 7 0.073,1.375 0.208,1.542 0.135,0.167 10 false 6 1.49,0.333 1.698,0.5 0.208,0.167 10 true 10 0.229,1.938 0.365,2.104 0.135,0.167 10 true 5 1.094,1.979 1.24,2.135 0.146,0.156 10 true 4 0.51,0.333 0.646,0.5 0.135,0.167 10 false 8 2.823,2.01 3.01,2.156 0.188,0.146 10 true 18 3.24,1.188 3.427,1.354 0.188,0.167 10 false 16 2.448,0.073 2.635,0.24 0.188,0.167 10 true 13 2.198,0.302 2.406,0.469 0.208,0.167 10 true 12 2.281,2 2.469,2.146 0.188,0.146 10 true 19 3.229,1.625 3.406,1.792 0.177,0.167 10 false 17 3.198,0.302 3.375,0.458 0.177,0.156 10 true 14 3.24,0.771 3.427,0.917 0.188,0.146 10 false 15

Temporarily install the cylinder head cover sub-assembly RH with the 18 bolts. Tighten the 18 bolts in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11202 4.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH

a.
A164159C01
0.948,2.01 1.146,2.167 0.198,0.156 10 true *a 0.385,2.01 0.552,2.156 0.167,0.146 10 false *a 0.604,0.406 0.781,0.573 0.177,0.167 10 true *a 0.854,0.052 1.083,0.219 0.229,0.167 10 true *a 0.031,1.594 0.25,1.771 0.219,0.177 10 false *a 0.031,1.104 0.229,1.292 0.198,0.188 10 false *a
*a Seal Packing


Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover sub-assembly LH within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

·

Do not start the engine for at least 2 hours after the installation.




b.

Install a new gasket to the cylinder head cover sub-assembly LH.

NOTICE:

Remove any oil from the contact surface.



c.
A164162N01
1.396,0.188 1.76,0.365 0.365,0.177 10 true 1, 11 1.385,1.948 1.74,2.115 0.354,0.167 10 true 2, 19 0.969,0.01 1.094,0.188 0.125,0.177 10 true 9 1.167,1.958 1.292,2.104 0.125,0.146 10 true 3 0.073,0.688 0.229,0.854 0.156,0.167 10 true 7 0.073,1.25 0.219,1.448 0.146,0.198 10 true 6 1.115,0.156 1.333,0.344 0.219,0.188 10 true 10 0.104,1.885 0.24,2.052 0.135,0.167 10 false 5 0.427,1.979 0.531,2.135 0.104,0.156 10 false 4 0.094,0.042 0.229,0.208 0.135,0.167 10 true 8 2,1.927 2.188,2.073 0.188,0.146 10 true 18 3.208,1.823 3.396,1.99 0.188,0.167 10 false 16 2.406,0.188 2.594,0.365 0.188,0.177 10 true 13 1.979,0.208 2.177,0.375 0.198,0.167 10 false 12 2.677,1.813 2.854,1.979 0.177,0.167 10 true 17 3.135,0.177 3.344,0.344 0.208,0.167 10 false 14 3.198,0.948 3.385,1.115 0.188,0.167 10 false 15

Temporarily install the cylinder head cover sub-assembly LH with the 17 bolts. Tighten the 17 bolts in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Connect the No. 3 ventilation hose to the cylinder head cover sub-assembly LH, and slide the clamp to secure the hose.


Hide 12270 5.INSTALL OIL SEPARATOR ASSEMBLY

a.

Install a new gasket to the oil separator assembly.

NOTICE:

Remove any oil from the contact surface.



b.

Install the oil separator assembly with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the ventilation hose to the oil separator assembly, and slide the clamp to secure the hose.


Hide 23681E 6.INSTALL NOZZLE HOLDER SEAL LH

a.

Press 4 new nozzle holder seal LH into the cylinder head cover sub-assembly LH.


Hide 23681D 7.INSTALL NOZZLE HOLDER SEAL RH

a.

Press 4 new nozzle holder seal RH into the cylinder head cover sub-assembly RH.


Hide 23801L 8.INSTALL FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY

Hide 23805B 10.INSTALL NO. 5 FUEL PIPE SUB-ASSEMBLY

Hide 23706 12.INSTALL NO. 6 INJECTION PIPE SUB-ASSEMBLY

Hide 17947B 15.INSTALL NO. 3 INTERCOOLER SUPPORT BRACKET

Hide 44761 21.INSTALL VACUUM PUMP TO CONNECTOR TUBE

Hide 44769 23.INSTALL VACUUM RESERVOIR CONNECT TUBE

Hide 23804D 24.INSTALL NO. 4 FUEL PIPE SUB-ASSEMBLY

Hide 16267 26.CONNECT NO. 2 WATER BY-PASS HOSE AND NO. 3 WATER BY-PASS HOSE

Hide 12142 27.INSTALL NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 26100G 28.INSTALL DIESEL THROTTLE BODY ASSEMBLY

Hide 17940D 29.INSTALL INTERCOOLER ASSEMBLY

Hide 30.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 33.REGISTER INJECTOR COMPENSATION CODE