Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0135612 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1407  Open or Short in Rear Speed Sensor RH Circuit  C1408  Open or Short in Rear Speed Sensor LH Circuit  


DESCRIPTION

Refer to DTCs C1403 and C1404.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1403

DTC No. Detection Item DTC Detection Condition Trouble Area
C1407 Open or Short in Rear Speed Sensor RH Circuit Either condition is met:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the IG1 terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Rear speed sensor RH

·

Skid control sensor wire

·

Speed sensor circuit

·

Brake actuator assembly (Skid control ECU)


C1408 Open or Short in Rear Speed Sensor LH Circuit Either condition is met:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the IG1 terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Rear speed sensor LH

·

Skid control sensor wire

·

Speed sensor circuit

·

Brake actuator assembly (Skid control ECU)



HINT:
·

DTC C1407 is for the rear speed sensor RH.

·

DTC C1408 is for the rear speed sensor LH.



WIRING DIAGRAM

C217557E21
5.385,2.76 5.802,2.906 0.417,0.146 10 false A20 5.385,2.948 7.125,3.333 1.74,0.385 10 false Brake Actuator Assembly (Skid Control ECU) 3.125,2.75 5.198,2.927 2.073,0.177 10 false Skid Control Sensor Wire 3.979,0.333 4.26,0.5 0.281,0.167 10 false V3 3.969,0.875 4.25,1.042 0.281,0.167 10 false V3 3.969,1.875 4.25,2.042 0.281,0.167 10 false V3 3.969,2.448 4.25,2.615 0.281,0.167 10 false V3 2.844,0.323 2.99,0.469 0.146,0.146 10 false C 2.844,0.875 2.99,1.021 0.146,0.146 10 false C 2.844,1.875 2.99,2.021 0.146,0.146 10 false D 2.844,2.448 2.99,2.594 0.146,0.146 10 false D 0.458,0.542 2,0.75 1.542,0.208 10 false Rear Speed Sensor RH 0.479,2.115 2.021,2.323 1.542,0.208 10 false Rear Speed Sensor LH 2.406,0.875 2.698,1.052 0.292,0.177 10 false RR- 2.865,0.125 2.969,0.271 0.104,0.146 10 false 3 2.396,0.323 2.708,0.5 0.313,0.177 10 false RR+ 4,0.688 4.135,0.854 0.135,0.167 10 false 4 4,0.135 4.177,0.292 0.177,0.156 10 false 3 2.854,0.667 3.031,0.823 0.177,0.156 10 false 1 2.385,2.448 2.677,2.625 0.292,0.177 10 false RL- 2.854,1.677 2.969,1.833 0.115,0.156 10 false 3 2.396,1.885 2.688,2.063 0.292,0.177 10 false RL+ 4.01,2.24 4.146,2.406 0.135,0.167 10 false 2 4.01,1.677 4.188,1.833 0.177,0.156 10 false 1 2.844,2.25 2.948,2.406 0.104,0.156 10 false 1 6.167,0.865 6.458,1.042 0.292,0.177 10 false RR- 6.167,0.333 6.542,0.51 0.375,0.177 10 false RR+ 6.167,2.438 6.458,2.615 0.292,0.177 10 false RL- 6.167,1.885 6.458,2.063 0.292,0.177 10 false RL+ 5.823,0.74 6.021,0.906 0.198,0.167 10 false 16 5.823,0.208 6.021,0.375 0.198,0.167 10 false 17 5.875,2.323 6.021,2.51 0.146,0.188 10 false 4 5.875,1.76 6.021,1.948 0.146,0.188 10 false 5 3.573,0.438 3.885,0.615 0.313,0.177 10 false RR+ 3.583,0.771 3.875,0.948 0.292,0.177 10 false RR- 3.594,1.99 3.885,2.167 0.292,0.177 10 false RL+ 3.604,2.333 3.896,2.51 0.292,0.177 10 false RL-

CAUTION / NOTICE / HINT

NOTICE:
·

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Speed Open Rear speed sensor RH open detection Error or Normal Normal -
RL Speed Open Rear speed sensor LH open detection Error or Normal Normal -
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Speed Open
RL Speed Open
50003 105 202,203
OK:

Normal (there are no momentary interruptions).


HINT:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (RR/RL WHEEL SPEED)

NG

4.INSPECT SKID CONTROL SENSOR WIRE
2.READ VALUE USING GTS (RR/RL WHEEL SPEED)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
RL Wheel Speed Rear speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
50003 105 3,4

f.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error.

This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.


OK:

The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

4.INSPECT SKID CONTROL SENSOR WIRE
3.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Proceed to
DTC is not output
DTC is output



DTC is not output

DTC is output

4.INSPECT SKID CONTROL SENSOR WIRE
C269768C04
1.198,0.813 1.365,1 0.167,0.188 3.427,0.542 3.729,0.74 0.302,0.198 5.844,0.833 6.021,1.01 0.177,0.177 0.635,2.115 0.635,2.021 0.635,2.021 1.042,1.563 false 1.927,2.125 1.927,2.021 1.927,2.021 1.51,1.573 false 5.385,2.146 5.385,2.021 5.385,2.021 5.698,1.563 false 6.479,2.135 6.479,2.031 6.479,2.031 6.177,1.563 false 3.792,1.344 4.167,0.833 4.167,0.833 4.25,0.833 true 3.458,1.344 3.167,0.833 3.167,0.833 3.083,0.833 true 3.427,1.573 2.917,1.917 2.917,1.917 2.917,2.083 true 3.792,1.583 4.25,1.917 4.25,1.917 4.25,2.083 true 6.094,0.708 6.406,0.865 0.313,0.156 10 false *A 1.417,0.688 1.729,0.844 0.313,0.156 10 false *B 0.083,0.094 0.396,0.25 0.313,0.156 10 false *1 1.208,2.229 1.521,2.385 0.313,0.156 10 false *a 3.563,2.146 3.875,2.302 0.313,0.156 10 false *b 3.76,0.406 4.073,0.563 0.313,0.156 10 false *c 1.24,0.833 1.396,1.031 0.156,0.198 10 false D 3.5,0.563 3.823,0.75 0.323,0.188 10 false V3 5.885,0.844 6.042,1.042 0.156,0.198 10 false C 0.552,2.146 0.865,2.333 0.313,0.188 10 false RL- 1.813,2.156 2.115,2.323 0.302,0.167 10 false RL+ 5.302,2.167 5.604,2.354 0.302,0.188 10 false RR- 6.375,2.167 6.677,2.344 0.302,0.177 10 false RR+ 5.896,2.292 6.104,2.479 0.208,0.188 10 false *a 4.281,0.76 4.594,0.948 0.313,0.188 10 false RL- 2.781,0.75 3.083,0.917 0.302,0.167 10 false RL+ 2.823,2.094 3.125,2.271 0.302,0.177 10 false RR+ 4.167,2.125 4.469,2.313 0.302,0.188 10 false RR-
*A for RH *B for LH
*1 Skid Control Sensor Wire - -
*a Front view of wire harness connector
(to Sensor Side Connector)
*b Front view of wire harness connector
(to Vehicle Side Connector)
*c Female - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
V3 female connector 3 (RR+) - C-3 (RR+) Always Below 1 Ω
V3 female connector 3 (RR+) or C-3 (RR+) - Body ground Always 10 kΩ or higher
V3 female connector 4 (RR-) - C-1 (RR-) Always Below 1 Ω
V3 female connector 4 (RR-) or C-1 (RR-) - Body ground Always 10 kΩ or higher
V3 female connector 3 (RR+) - V3 female connector 1 (RL+) Always 10 kΩ or higher
V3 female connector 3 (RR+) - V3 female connector 2 (RL-) Always 10 kΩ or higher
V3 female connector 3 (RR+) - V3 female connector 4 (RR-) Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
V3 female connector 1 (RL+) - D-3 (RL+) Always Below 1 Ω
V3 female connector 1 (RL+) or D-3 (RL+) - Body ground Always 10 kΩ or higher
V3 female connector 2 (RL-) - D-1 (RL-) Always Below 1 Ω
V3 female connector 2 (RL-) or D-1 (RL-) - Body ground Always 10 kΩ or higher
V3 female connector 1 (RL+) - V3 female connector 2 (RL-) Always 10 kΩ or higher
V3 female connector 1 (RL+) - V3 female connector 3 (RR+) Always 10 kΩ or higher
V3 female connector 1 (RL+) - V3 female connector 4 (RR-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)

NG

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)

b.

Disconnect the A20 brake actuator assembly (skid control ECU) connector.


c.

Disconnect the C and/or D speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A20-17 (RR+) - C-3 (RR+) Always Below 1 Ω
A20-17 (RR+) or C-3 (RR+) - Body ground Always 10 kΩ or higher
A20-16 (RR-) - C-1 (RR-) Always Below 1 Ω
A20-16 (RR-) or C-1 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A20-5 (RL+) - D-3 (RL+) Always Below 1 Ω
A20-5 (RL+) or D-3 (RL+) - Body ground Always 10 kΩ or higher
A20-4 (RL-) - D-1 (RL-) Always Below 1 Ω
A20-4 (RL-) or D-1 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (RR+/RL+ TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (RR+/RL+ TERMINAL)
a.

Connect the brake actuator assembly (skid control ECU) connector.


b.
C269769C02
1.604,0.135 1.833,0.333 0.229,0.198 1.604,0.406 1.833,0.594 0.229,0.188 2,1.281 2.698,1.469 2.698,1.469 2.698,1.563 false 1.885,0.083 2.198,0.24 0.313,0.156 10 false *A 1.885,0.375 2.198,0.531 0.313,0.156 10 false *B 0.083,0.073 0.396,0.229 0.313,0.156 10 false *a 1.667,0.146 1.823,0.344 0.156,0.198 10 false C 1.667,0.417 1.823,0.615 0.156,0.198 10 false D 2.49,1.583 2.948,1.781 0.458,0.198 10 false RR+ 2.49,1.75 2.948,1.948 0.458,0.198 10 false RL+ 2.76,1.583 3.073,1.781 0.313,0.198 10 false *A, 2.75,1.75 3.063,1.948 0.313,0.198 10 false *B
*A for RH
*B for LH
*a Front view of wire harness connector
(to Rear Speed Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Switch Condition Specified Condition
C-3 (RR+) - Body ground Ignition switch ON 11 to 14 V

for LH
Tester Connection Switch Condition Specified Condition
D-3 (RL+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG