Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0135612 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1417  High Power Supply Voltage Malfunction  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the brake actuator assembly (skid control ECU) stores this DTC and the fail-safe function prohibits ABS operation.

This DTC is stored when the IG1 terminal voltage deviates from the DTC detection condition due to a malfunction in the power supply or charging circuit such as the battery or generator circuit, etc.

The DTC is canceled when the IG1 terminal voltage returns to normal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1417 High Power Supply Voltage Malfunction The IG1 terminal voltage is 17.4 V or more for 0.8 seconds or more.
·

ECU IG fuse

·

Battery

·

Charging system

·

Power source circuit

·

Internal power supply circuit of the brake actuator assembly (skid control ECU)



CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

NG

2.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.

Disconnect the A20 brake actuator assembly (skid control ECU) connector.


b.

Turn the ignition switch to ON.


c.
C260095C19
0.177,0.917 0.51,1.177 0.333,0.26 2.094,1.833 2.302,1.396 true 0.052,0.042 0.365,0.198 0.313,0.156 10 false *a 0.229,0.969 0.542,1.167 0.313,0.198 10 false A20 1.865,1.792 2.167,2 0.302,0.208 10 false IG1
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A20-34 (IG1) - Body ground Ignition switch ON 11 to 14 V



HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.


Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

3.RECONFIRM DTC
a.

Connect the brake actuator assembly (skid control ECU) connector.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Check if the same DTC is recorded.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC is not output
DTC is output




DTC is not output

DTC is output