Home › Engine / Hybrid System › 1GR-FE (FUEL) › FUEL TANK (for 90 L Tank Carried in Middle) › 2014.08–2022.09
RM25T0E _51 Engine / Hybrid System _029892 1GR-FE FUEL _0135862 FUEL TANK(for 90 L Tank Carried in Middle) A

1GR-FE FUEL  FUEL TANK(for 90 L Tank Carried in Middle)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, watching time may be required before disconnecting the cable from the battery teminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 4.DRAIN FUEL

a.
A221861

Loosen the fuel tank plug and drain the fuel from the fuel tank assembly.


b.

Install a new gasket and the fuel tank plug to the fuel tank assembly.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 37110 10.REMOVE PROPELLER SHAFT ASSEMBLY

Hide 77266A 11.REMOVE NO. 1 FUEL TUBE PROTECTOR

Hide 77267A 12.REMOVE NO. 2 FUEL TUBE PROTECTOR

a.
A220483

Remove the 3 bolts and No. 2 fuel tube protector.


Hide 13.DISCONNECT FUEL HOSE AND FUEL TUBE (for Single Tank Type)

a.
A220484

Disconnect the fuel main tube from the No. 2 fuel main tube sub-assembly.

Click hereEngine / Hybrid System>1GR-FE (FUEL)>FUEL SYSTEM>PRECAUTION


b.

Slide the clamp and disconnect the fuel return hose No. 2 fuel main tube sub-assembly.


c.

Slide the clamp and disconnect the fuel evaporation hose No. 2 fuel main tube sub-assembly.


Hide 14.REMOVE NO. 4 FUEL TUBE PROTECTOR (for Double Tank Type)

a.
A220795

Remove the 2 bolts and No. 4 fuel tube protector.


Hide 15.REMOVE NO. 5 FUEL TUBE PROTECTOR (for Double Tank Type)

a.
A220796

Remove the 2 bolts and No. 5 fuel tube protector.


Hide 77206C 16.DISCONNECT NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)

a.

Disconnect the fuel main tube from the No. 2 fuel main tube sub-assembly labeled A in the illustration.

Click hereEngine / Hybrid System>1GR-FE (FUEL)>FUEL SYSTEM>PRECAUTION


b.

Slide the clamp and disconnect the fuel return hose from the No. 2 fuel main tube sub-assembly labeled A in the illustration.


c.

Slide the clamp and disconnect the fuel evaporation hose from the No. 2 fuel main tube sub-assembly labeled A in the illustration.


d.

Disconnect the 3 clamps and remove the bolt and No. 1 fuel tube clamp labeled A in the illustration.


e.

Slide the 2 clamps and disconnect the 2 fuel hoses and 2 fuel main tubes from the No. 2 fuel main tube sub-assembly labeled B in the illustration.

Click hereEngine / Hybrid System>1GR-FE (FUEL)>FUEL SYSTEM>PRECAUTION


f.

Slide the clamp and disconnect the fuel hose and fuel main tube from the No. 2 fuel main tube sub-assembly labeled C in the illustration.

Click hereEngine / Hybrid System>1GR-FE (FUEL)>FUEL SYSTEM>PRECAUTION


g.

Detach the 2 fuel tube clamps labeled D in the illustration.


h.

Remove the 2 bolts labeled E in the illustration.

A220687N01
1.448,0.094 1.635,0.292 0.188,0.198 10 true A 6.854,0.073 7.021,0.25 0.167,0.177 10 true B 1.458,3.219 1.625,3.396 0.167,0.177 10 true C 6.844,3.208 7.01,3.385 0.167,0.177 10 true D 4.823,3.219 5,3.406 0.177,0.188 10 true E


Hide 77277R 17.REMOVE FUEL TANK FILLER PIPE PROTECTOR

a.
A224487

Remove the 3 bolts and fuel tank filler pipe protector.


Hide 77213 18.DISCONNECT FUEL INLET HOSE

a.
A220790

Loosen the clamp and disconnect the fuel inlet hose from the fuel tank inlet pipe sub-assembly.


Hide 77100D 19.DISCONNECT FUEL BREATHER HOSE

a.
A220689

Slide the clamp and disconnect the fuel breather hose from the fuel tank inlet pipe sub-assembly.


Hide 77100 20.REMOVE FUEL TANK ASSEMBLY

a.
A221863

Disconnect the fuel sender gauge connector and fuel pump connector and detach the clamp.


b.
A220794

Detach the wire harness clamp.


c.

Set an engine lifter underneath the fuel tank assembly.


d.
A221862

Remove the 2 bolts, 2 pins and disconnect the 2 fuel tank bands.


e.

Slightly lower the engine lifter.


f.

Remove the No. 1 fuel tank protector sub-assembly from fuel tank assembly.


Hide 21.REMOVE FUEL HOSE

a.
A220486

Remove the fuel main hose from the fuel suction tube sub-assembly.

Click hereEngine / Hybrid System>1GR-FE (FUEL)>FUEL SYSTEM>PRECAUTION


b.

Slide the clamp and remove the fuel return hose from the fuel suction tube sub-assembly.


c.

Slide the clamp and remove the fuel evaporation hose from the No. 1 fuel evaporation tube sub-assembly.


d.
A220487

Loosen the clamp and remove the fuel inlet hose from the fuel tank filler lower pipe sub-assembly.


e.

Slide the clamp and remove the fuel breather hose from the fuel tank assembly.


Hide 77026A 22.REMOVE NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.
A220489

Remove the 8 screws, 2 nuts and No. 1 fuel evaporation tube sub-assembly from the fuel tank assembly.


b.

Remove the 2 gaskets from the No. 1 fuel evaporation tube sub-assembly .


Hide 77380 23.REMOVE FUEL CUT OFF VALVE ASSEMBLY

a.

Remove the fuel cut off valve assembly from the fuel tank assembly.


Hide 77420 24.REMOVE NO. 2 FUEL CUT OFF VALVE ASSEMBLY

a.

Remove the No. 2 fuel cut off valve assembly from the fuel tank assembly.


Hide 77203B 26.REMOVE FUEL SUCTION TUBE SUB-ASSEMBLY

a.
A308602

Remove the 8 screws and fuel suction tube sub-assembly from the fuel tank assembly.


b.

Remove the gasket from the fuel suction tube sub-assembly.


Hide 77011 27.REMOVE FUEL TANK FILLER LOWER PIPE SUB-ASSEMBLY

a.
A220488

Remove the 6 screws and fuel tank filler lower pipe sub-assembly from the fuel tank assembly.


b.

Remove the gasket from the fuel tank filler lower pipe sub-assembly.