Home › Engine / Hybrid System › 1VD-FTV (INTAKE / EXHAUST) › EXHAUST MANIFOLD W/ TURBOCHARGER (w/o DPF) › 2014.08–2022.09
RM25T0E _51 Engine / Hybrid System _029894 1VD-FTV INTAKE / EXHAUST _0136509 EXHAUST MANIFOLD W/ TURBOCHARGER(w/o DPF) A

1VD-FTV INTAKE / EXHAUST  EXHAUST MANIFOLD W/ TURBOCHARGER(w/o DPF)  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:
·

Wear protective gloves when removing the exhaust pipe.

·

The exhaust pipe is extremely hot immediately after the engine has stopped.

·

Confirm that the exhaust pipe has cooled down before removing it.



PROCEDURE

Hide 1.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 53736 4.REMOVE FRONT FENDER APRON SEAL RH

a.

Remove the 11 clips and front fender apron seal RH.


Hide 53737B 5.REMOVE FRONT FENDER APRON SEAL LH

a.

Remove the 11 clips and front fender apron seal LH.


Hide 6.REMOVE ENGINE OIL LEVEL DIPSTICK

Hide 12142 7.REMOVE NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 11452 8.REMOVE NO. 1 ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 51442 9.REMOVE NO. 2 ENGINE UNDER COVER

Hide 18421C 12.REMOVE CENTER CONVERTER PROTECTOR STAY

a.
A166012

Remove the 3 bolts and center converter protector stay.


Hide 18450A 13.REMOVE MONOLITHIC CONVERTER ASSEMBLY

a.
A166013

Remove the 2 bolts and 2 compression springs.


b.
A164686

Remove the 3 nuts, monolithic converter assembly and gasket.


c.
A162139

Remove the gasket.


Hide 87249B 14.REMOVE OUTLET HEATER WATER PIPE B

Hide 17940D 15.REMOVE INTERCOOLER ASSEMBLY

Hide 16571C 18.REMOVE NO. 1 RADIATOR HOSE

Hide 17881 19.REMOVE NO. 1 AIR CLEANER HOSE

Hide 17705 20.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

a.
A163346

Detach the 4 clamps and remove the air cleaner cap sub-assembly from the air cleaner case sub-assembly.


b.

Remove the air cleaner filter element sub-assembly from the air cleaner case sub-assembly.


Hide 21.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 22.REMOVE INTAKE AIR CONNECTOR SUB-ASSEMBLY

Hide 17875 23.REMOVE INTAKE AIR CONNECTOR PIPE

Hide 16361A 24.REMOVE FAN AND GENERATOR V-RIBBED BELT

Hide 16470 25.REMOVE RADIATOR RESERVOIR ASSEMBLY

Hide 16711 26.REMOVE FAN SHROUD

Hide 16371 27.REMOVE FAN PULLEY

Hide 16572D 28.DISCONNECT NO. 2 RADIATOR HOSE

Hide 16400 29.REMOVE RADIATOR ASSEMBLY

Hide 27280 30.REMOVE GENERATOR SPLASH GUARD COVER ASSEMBLY

Hide 27020 31.REMOVE GENERATOR ASSEMBLY

Hide 15778 32.DISCONNECT NO. 2 OIL COOLER HOSE

Hide 16603B 33.REMOVE IDLER PULLEY SUB-ASSEMBLY

Hide 16620D 34.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 17878 35.REMOVE NO. 3 INTAKE AIR CONNECTOR PIPE

Hide 17362B 36.REMOVE NO. 2 AIR TUBE

A165354

a.

Remove the bolt.


b.

Loosen the clamp and remove the No. 2 air tube.


Hide 17343D 37.REMOVE NO. 3 AIR HOSE

A165355

a.

Loosen the clamp and remove the No. 3 air hose.


Hide 17361J 38.REMOVE NO. 1 AIR TUBE

A164252

a.

Remove the 2 bolts, No. 1 air tube and gasket.


Hide 16027 39.REMOVE NO. 1 TURBO WATER PIPE SUB-ASSEMBLY

a.
A164251

Slide the clip and disconnect the No. 1 turbo water hose from the No. 1 turbo water pipe sub-assembly.


b.

Remove the bolt.


c.
A164250

Slide the clip and disconnect the No. 2 turbo water hose from the No. 1 turbo water pipe sub-assembly.


d.

Remove the bolt.


e.
A164249

Remove the 2 nuts, No. 1 turbo water pipe sub-assembly and gasket.


Hide 17293 40.REMOVE TURBOCHARGER STAY

Hide 15769 42.REMOVE OIL COOLER PIPE

Hide 15407 43.DISCONNECT INLET TURBO OIL PIPE SUB-ASSEMBLY

Hide 83520 44.REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY

Hide 45.REMOVE ENGINE WIRE BRACKET

Hide 15474A 46.REMOVE OUTLET TURBO OIL HOSE

Hide 25708 47.REMOVE NO. 3 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

Hide 12201 48.REMOVE VENTILATION TUBE SUB-ASSEMBLY

Hide 12102A 50.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

Hide 15614 51.REMOVE LOWER OIL FILTER ELEMENT COVER

Hide 12101 53.REMOVE OIL PAN SUB-ASSEMBLY

Hide 54.REMOVE TUBE SUB-ASSEMBLY (w/ Air Conditioning System)

Hide 17168 55.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.
A334051

w/ Air Conditioning System:

Remove the 2 bolts and clamp, and disconnect the No. 1 fuel tube bracket.


b.

Remove the bolt and disconnect the fuel tube bracket.


c.

Detach the clamp and disconnect the engine wire.


d.
A164691

Remove the 3 bolts and No. 2 exhaust manifold heat insulator.


Hide 17167 56.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.
A164689

Remove the 3 bolts and No. 1 exhaust manifold heat insulator.


Hide 17106 58.REMOVE EXHAUST CROSSOVER PIPE SUB-ASSEMBLY

a.
A169516

Remove the 2 bolts, 6 nuts, exhaust crossover pipe sub-assembly and 2 gaskets.


Hide 17119 59.REMOVE NO. 2 MANIFOLD STAY

a.
A166638

Remove the 2 bolts and No. 2 manifold stay.


Hide 17118 60.REMOVE NO. 1 MANIFOLD STAY

a.
A164468

Remove the bolt and No. 1 manifold stay.


Hide 17142 61.REMOVE EXHAUST MANIFOLD LH

a.
A164248

Remove the 10 nuts, 10 collars, exhaust manifold LH with turbocharger sub-assembly and gasket.


b.
A164247

Remove the 3 nuts, exhaust manifold LH and gasket from the turbocharger sub-assembly.


Hide 17141 62.REMOVE EXHAUST MANIFOLD RH

a.
A164698

Remove the 10 nuts, 10 collars, exhaust manifold RH and gasket.


Hide 15407 63.REMOVE INLET TURBO OIL PIPE SUB-ASSEMBLY

A164246

a.

Remove the union bolt.


b.

Remove the bolt, inlet turbo oil pipe sub-assembly and gasket.


Hide 15481 64.REMOVE NO. 1 TURBO OIL PIPE

A164245

a.

Remove the 2 bolts, No. 1 turbo oil pipe and gasket.


Hide 17274 65.REMOVE INLET COMPRESSOR ELBOW

A164244

a.

Remove the 2 bolts, inlet compressor elbow and gasket.


Hide 66.REMOVE STUD BOLT

A165361

a.

Using an E10 "TORX" socket wrench, remove the 6 stud bolts.

NOTICE:

If the stud bolt is deformed or its threads are damaged, replace it.