Home › Engine / Hybrid System › 1GR-FE (ENGINE MECHANICAL) › CAMSHAFT
RM25T0E _51 Engine / Hybrid System _029891 1GR-FE ENGINE MECHANICAL _0136555 CAMSHAFT A

1GR-FE ENGINE MECHANICAL  CAMSHAFT  INSTALLATION  


PROCEDURE

Hide 13050 1.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13053 2.INSTALL NO. 3 CAMSHAFT SUB-ASSEMBLY

NOTICE:

As the thrust clearance of the No. 3 camshaft sub-assembly is small, the No. 3 camshaft sub-assembly must be kept level while it is being installed. If the No. 3 camshaft sub-assembly is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the No. 3 camshaft sub-assembly to seize or break. To avoid this, make sure the following steps are carried out.


a.

Apply new engine oil to the thrust portions and journals of the No. 3 camshaft sub-assembly.


b.
A316681C01
0.75,0.25 0.917,0.25 0.917,0.25 0.917,0.583 true 2.125,0.094 2.292,0.094 2.292,0.094 2.292,0.594 true 1.75,1.917 2.323,0.688 true 1.583,1.917 1.75,1.917 1.75,1.917 2.25,0.667 true 0.583,0.177 0.896,0.333 0.313,0.156 10 false *a 1.417,1.823 1.729,1.979 0.313,0.156 10 false *b 1.948,0 2.26,0.156 0.313,0.156 10 false *a
*a Mark Link (Yellow)
*b Timing Mark


Align the mark link (yellow) with the timing mark of the camshaft timing gear assembly.


c.
A316682C01
2.271,0.76 2.688,0.938 2.688,0.938 2.917,0.938 true 1.667,1.219 0.927,1.5 0.927,1.5 0.792,1.5 true 0.615,1.438 0.896,1.677 0.281,0.24 10 false *1 2.969,0.865 3.281,1.021 0.313,0.156 10 true *2
*1 Chain Sub-assembly
*2 No. 2 Chain Sub-assembly


Temporarily install the chain sub-assembly to the No. 2 chain sub-assembly.


d.
A316683C01
1.49,0.156 1.677,0.156 1.677,0.156 1.677,0.792 true 1.344,0.073 1.656,0.229 0.313,0.156 10 false *a
*a Knock Pin


Align the knock pin hole of the camshaft timing gear assembly with the knock pin of the No. 3 camshaft sub-assembly and temporarily install the No. 3 camshaft sub-assembly to the camshaft timing gear assembly with the bolt.


e.
A326551

Set the No. 3 camshaft sub-assembly to the cylinder head LH as shown in the illustration.


f.
A326552

Check the numbers on the camshaft bearing caps and the installation direction before temporarily placing each cap.


g.

Apply a light coat of engine oil to the threads and under the heads of the bolts.


h.
A316678C02
0.906,0.229 1.063,0.427 0.156,0.198 10 true 4 1.427,0.333 1.583,0.531 0.156,0.198 10 true 2 2.135,0.344 2.292,0.542 0.156,0.198 10 true 6 2.792,0.344 2.948,0.542 0.156,0.198 10 true 8 0.938,1.385 1.094,1.583 0.156,0.198 10 true 3 1.417,1.354 1.573,1.552 0.156,0.198 10 true 1 2.115,1.323 2.271,1.521 0.156,0.198 10 true 5 2.802,1.323 2.958,1.521 0.156,0.198 10 true 7
V100135

Bolt A
V100136

Bolt B


Install and uniformly tighten the 8 bolts in several steps in the sequence shown in the illustration.

Torque:
for bolt A : 9.0 N*m (92 kgf*cm, 80 in.*lbf)
for bolt B : 24 N*m (245 kgf*cm, 18 ft.*lbf)

Standard Bolt Length:
Item Specified Condition
Bolt A 39 mm (1.54 in.)
Bolt B 50 mm (1.97 in.)



i.
A326553C01
1.167,0.25 1.333,0.25 1.333,0.25 1.708,0.698 true 0.417,1.75 0.583,1.75 0.583,1.75 1.594,0.781 true 0.583,1.75 1.698,0.875 true 1,0.177 1.25,0.417 0.25,0.24 10 true *a 0.25,1.656 0.563,1.813 0.313,0.156 10 false *b
*a Paint Mark
*b Timing Mark


Set the paint mark of the chain sub-assembly between the timing marks of the camshaft timing gear assembly.


j.
A326554

Hold the hexagonal portion of the No. 3 camshaft sub-assembly with a wrench and tighten the bolt.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


Hide 13560A 3.INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY

a.
A326555C01
2.573,1.115 2.885,1.271 0.313,0.156 10 false *a
*a Push


While pushing in the No. 3 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to fix the No. 3 chain tensioner assembly in place.


b.
A326556C01
1.417,0.198 1.625,0.198 1.625,0.198 2.125,0.604 true 0.844,1.021 1.01,1.021 1.01,1.021 1.25,1.281 true 2.177,0.677 2.5,0.833 2.5,0.833 2.75,0.833 true 2.115,0.708 2.5,0.833 true 1.292,1.365 1.583,1.917 1.583,1.917 1.75,1.917 true 1.25,0.104 1.563,0.302 0.313,0.198 10 false *a 2.813,0.74 3,0.917 0.188,0.177 10 true *b 0.677,0.927 0.99,1.125 0.313,0.198 10 false *a 1.781,1.833 1.969,2.01 0.188,0.177 10 true *b
*a Mark Link (Yellow)
*b Timing Mark


Temporarily install the camshaft timing sprocket and No. 3 chain tensioner assembly with the bolt and align the mark links (yellow) with the timing marks of the camshaft timing gear assembly and camshaft timing sprocket.


c.

Tighten the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 13054 4.INSTALL NO. 4 CAMSHAFT SUB-ASSEMBLY

NOTICE:

As the thrust clearance of the No. 4 camshaft sub-assembly is small, the No. 4 camshaft sub-assembly must be kept level while it is being installed. If the No. 4 camshaft sub-assembly is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the No. 4 camshaft sub-assembly to seize or break. To avoid this, make sure the following steps are carried out.


a.

Apply new engine oil to the thrust portions and journals of the No. 4 camshaft sub-assembly.


b.
A326557

Align the knock pin hole of the camshaft timing sprocket with the knock pin of the No. 4 camshaft sub-assembly and temporarily install the No. 4 camshaft sub-assembly to the camshaft timing sprocket with the bolt.


c.
A326558

Check the numbers on the camshaft bearing caps and the installation direction before temporarily placing each cap.


d.

Apply a light coat of engine oil to the threads of the bolts.


e.
A316673C02
1.104,0.958 1.229,1.125 0.125,0.167 10 true 3 1.635,1.021 1.76,1.188 0.125,0.167 10 true 1 2.281,1.021 2.448,1.219 0.167,0.198 10 true 5 2.958,1.052 3.125,1.271 0.167,0.219 10 true 7 1.073,1.969 1.198,2.135 0.125,0.167 10 true 4 1.573,1.927 1.75,2.125 0.177,0.198 10 true 2 2.219,1.927 2.344,2.094 0.125,0.167 10 true 6 2.885,1.917 3.01,2.083 0.125,0.167 10 true 8
V100135

Bolt A
V100136

Bolt B


Install and uniformly tighten the 8 bearing cap bolts in several steps in the sequence shown in the illustration.

Torque:
for bolt A : 9.0 N*m (92 kgf*cm, 80 in.*lbf)
for bolt B : 24 N*m (245 kgf*cm, 18 ft.*lbf)

Standard Bolt Length:
Item Specified Condition
Bolt A 39 mm (1.54 in.)
Bolt B 50 mm (1.97 in.)



f.
A326559

Hold the hexagonal portion of the No. 4 camshaft sub-assembly with a wrench and tighten the bolt.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


g.

Remove the pin from the No. 3 chain tensioner assembly.


h.
A326560

Release the chain tension between the camshaft timing gear assembly (for bank 1) and crankshaft timing sprocket by turning the crankshaft clockwise slightly.


Hide 13511 5.INSTALL CAMSHAFT

NOTICE:

As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being installed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, make sure the following steps are carried out.


a.

Apply new engine oil to the thrust portions and journals of the camshaft.


b.
A326561C01
1.135,0.583 1.333,0.167 1.333,0.167 1.5,0.167 true 2.552,0.583 2.75,0.167 2.75,0.167 2.917,0.167 true 1.156,0.698 2.021,0.865 2.021,0.865 2.188,0.865 true 1.542,0.094 1.854,0.25 0.313,0.156 10 false *a 2.25,0.76 2.563,0.917 0.313,0.156 10 false *b 2.958,0.094 3.271,0.25 0.313,0.156 10 false *a
*a Mark Link (Yellow)
*b Timing Mark


Align the mark link (yellow) with the timing mark of the camshaft timing gear assembly.


c.
A326562

Temporarily install the chain sub-assembly to the No. 2 chain sub-assembly.


d.
A326563C01
1.563,0.802 1.823,0.156 1.823,0.156 2.031,0.156 true 2.073,0.083 2.385,0.24 0.313,0.156 10 false *a
*a Knock Pin


Align the knock pin hole of the camshaft timing gear assembly with the knock pin of the camshaft and temporarily install the camshaft timing gear assembly to the camshaft with the bolt.


e.
A326564

Set the camshaft to the cylinder head sub-assembly as shown in the illustration.


f.
A326565

Check the numbers on the camshaft bearing caps and the installation direction before temporarily placing each cap.


g.

Apply a light coat of engine oil to the threads and under the heads of the bolts.


h.
A316668C02
0.76,0.281 0.917,0.469 0.156,0.188 10 true 8 1.49,0.281 1.646,0.469 0.156,0.188 10 true 6 2.167,0.313 2.323,0.5 0.156,0.188 10 true 2 2.552,0.219 2.708,0.406 0.156,0.188 10 true 4 0.76,1.479 0.917,1.667 0.156,0.188 10 true 7 1.479,1.448 1.635,1.635 0.156,0.188 10 true 5 2.188,1.448 2.344,1.635 0.156,0.188 10 true 1 2.583,1.542 2.74,1.729 0.156,0.188 10 true 3
V100135

Bolt A
V100136

Bolt B


Install and uniformly tighten the 8 bolts in several steps in the sequence shown in the illustration.

Torque:
for bolt A : 9.0 N*m (92 kgf*cm, 80 in.*lbf)
for bolt B : 24 N*m (245 kgf*cm, 18 ft.*lbf)

Standard Bolt Length:
Item Specified Condition
Bolt A 39 mm (1.54 in.)
Bolt B 50 mm (1.97 in.)



i.
A326566C01
2.094,1.031 2.583,0.333 true 2.302,1.125 2.583,0.333 2.583,0.333 2.75,0.333 true 2.823,0.24 3.135,0.438 0.313,0.198 10 false *a
*a Timing Mark


Rotate the camshaft and align the timing mark of the camshaft timing gear assembly with the timing mark of the camshaft bearing cap.


j.
A326567C01
1.896,0.698 2.417,0.167 2.417,0.167 2.583,0.167 true 1.979,0.792 2.979,0.792 true 2.625,0.083 2.938,0.24 0.313,0.156 10 true *a 3.031,0.719 3.344,0.875 0.313,0.156 10 false *b
*a Paint Mark
*b Timing Mark


Align the paint mark of the chain sub-assembly with the timing mark of the camshaft timing gear assembly.


k.
A326568

Hold the hexagonal portion of the camshaft with a wrench and tighten the bolt.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


Hide 13550 6.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A326569C01
2.542,1.146 2.854,1.302 0.313,0.156 10 false *a
*a Push


While pushing in the No. 2 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to fix the No. 2 chain tensioner assembly in place.


b.
A326570C01
1.021,0.74 2.083,0.25 2.083,0.25 2.333,0.25 true 2.198,1.083 2.083,0.25 true 1,0.833 0.75,1.083 0.75,1.083 0.583,1.083 true 2.167,1.167 2.417,1.917 2.417,1.917 2.583,1.917 true 2.385,0.177 2.698,0.375 0.313,0.198 10 false *a 0.354,1 0.583,1.198 0.229,0.198 10 true *b 2.635,1.844 2.865,2.042 0.229,0.198 10 true *b
*a Mark Link (Yellow)
*b Timing Mark


Temporarily install the camshaft timing sprocket and No. 2 chain tensioner assembly with the bolt and align the mark links (yellow) with the timing marks of the camshaft timing gear assembly and camshaft timing sprocket.


c.

Tighten the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 13512 7.INSTALL NO. 2 CAMSHAFT

NOTICE:

As the thrust clearance of the No. 2 camshaft is small, the No. 2 camshaft must be kept level while it is being installed. If the No. 2 camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the No. 2 camshaft to seize or break. To avoid this, make sure the following steps are carried out.


a.

Apply new engine oil to the thrust portions and journals of the No. 2 camshaft.


b.
A326571

Set the No. 2 camshaft to the cylinder head sub-assembly as shown in the illustration.


c.
A326572

Check the numbers on the camshaft bearing caps and the installation direction before temporarily placing each cap.


d.

Apply a light coat of engine oil to the threads and under the bolts.


e.
A316663C02
0.552,1.958 0.708,2.156 0.156,0.198 10 false 8 1.26,1.969 1.417,2.167 0.156,0.198 10 false 6 1.927,1.979 2.083,2.177 0.156,0.198 10 false 2 2.26,1.969 2.417,2.167 0.156,0.198 10 false 4 0.74,0.99 0.896,1.188 0.156,0.198 10 true 7 1.417,1 1.573,1.198 0.156,0.198 10 true 5 2.083,1 2.24,1.198 0.156,0.198 10 true 1 2.531,0.938 2.688,1.135 0.156,0.198 10 true 3
V100135

Bolt A
V100136

Bolt B


Install and uniformly tighten the 8 bolts in several steps in the sequence shown in the illustration.

Torque:
for bolt A : 9.0 N*m (92 kgf*cm, 80 in.*lbf)
for bolt B : 24 N*m (245 kgf*cm, 18 ft.*lbf)

Standard Bolt Length:
Item Specified Condition
Bolt A 39 mm (1.54 in.)
Bolt B 50 mm (1.97 in.)



f.
A326573C01
1.594,1.552 2.5,2 2.5,2 2.667,2 true 2.719,1.917 3.031,2.073 0.313,0.156 10 false *a
*a Knock Pin


Rotate the No. 2 camshaft and align the knock pin hole of the camshaft timing gear assembly with the knock pin of the No. 2 camshaft.


g.
A326574

Hold the hexagonal portion of the No. 2 camshaft with a wrench and install the bolt.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


h.

Remove the pin from the No. 2 chain tensioner assembly.


Hide 13540 8.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

a.

Install the No. 1 chain tensioner assembly.

Click hereEngine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>ENGINE UNIT>REASSEMBLY


b.

Remove the bar from the No. 1 chain tensioner assembly.


Hide 11324 9.INSTALL TIMING CHAIN COVER PLATE

a.

Install a new gasket and the timing chain cover plate with the 4 bolts.

Torque:
9.1 N*m (93 kgf*cm, 81 in.*lbf)


Hide 10.SET NO. 1 CYLINDER TO TDC/COMPRESSION

Hide 11202 13.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH

Hide 11201 14.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 23801P 16.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY AND NO. 2 FUEL PIPE SUB-ASSEMBLY