41110F 1.INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY
Clean the contact surfaces of the front differential carrier and the front axle housing.
Install a new gasket and the differential carrier with the 10 nuts and 10 washers.
Be careful not to damage the installation surface.
Remove any foreign matter (dirt, gasket remains, metal particles, etc.) from the contact surfaces of the housing and differential carrier and install a new gasket.
2.CONNECT WIRE HARNESS
3.INSTALL FRONT AXLE SHAFT ASSEMBLY
4.INSTALL FRONT BRAKE TUBE (w/o ABS)
for 1HZ, 1VD-FTV:
| *a | Torque Wrench Fulcrum Length | - | - |
Install the brake tube, 3-way joint and brake hose with the 4 bolts.
Using a union nut wrench, connect each brake tube to the flexible hose while holding the flexible hose with a wrench.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 300 mm (11.811 in.)): 14.2 N*m (145 kgf*cm, 10 ft.*lbf)
Install the brake tube with a new clip.
for 1GR-FE:
| *a | Torque Wrench Fulcrum Length | - | - |
Install the brake tube, 3-way joint and brake hose with the 4 bolts.
Using a union nut wrench, connect each brake tube to the flexible hose while holding the flexible hose with a wrench.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 300 mm (11.811 in.)): 14.2 N*m (145 kgf*cm, 10 ft.*lbf)
Install the brake tube with a new clip.
5.INSTALL FRONT BRAKE TUBE (w/ ABS)
for 1HZ, 1VD-FTV:
| *a | Torque Wrench Fulcrum Length | - | - |
Install the brake tube with the 5 bolts.
Using a union nut wrench, connect each brake tube to the flexible hose while holding the flexible hose with a wrench.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 300 mm (11.811 in.)): 14.2 N*m (145 kgf*cm, 10 ft.*lbf)
Install the brake tube with 2 new clips.
for 1GR-FE:
| *a | Torque Wrench Fulcrum Length | - | - |
Install the brake tube with the 3 bolts.
Using a union nut wrench, connect each brake tube to the flexible hose while holding the flexible hose with a wrench.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 300 mm (11.811 in.)): 14.2 N*m (145 kgf*cm, 10 ft.*lbf)
37140 6.INSTALL FRONT PROPELLER SHAFT ASSEMBLY
7.ADD DIFFERENTIAL OIL