Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM25T0E _56 Audio / Visual / Telematics _029922 AUDIO / VIDEO _0137647 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Radio Broadcast cannot be Received (Bad Reception)  


WIRING DIAGRAM

E304758E01
0.438,1 4.719,1.198 4.281,0.198 10 false Antenna with Holder Assembly 0.167,0.125 4.448,0.323 4.281,0.198 12 false w/ CD Player: 3.708,0.49 5.823,0.865 2.115,0.375 10 false Antenna Cord Sub-assembly 5.417,4.073 5.917,4.396 0.5,0.323 10 false RA 5.396,4.25 7.021,4.604 1.625,0.354 10 false Radio Receiver Assembly 5.958,2.281 6.458,2.604 0.5,0.323 10 false ANT+ 5.948,1.313 6.448,1.635 0.5,0.323 10 false MAIN 3.719,1.385 4.219,1.708 0.5,0.323 10 false A 3.74,2.281 4.24,2.604 0.5,0.323 10 false B 3.74,2.063 4.24,2.385 0.5,0.323 10 false 1 3.719,1.156 4.219,1.479 0.5,0.323 10 false 1 2.354,2.281 2.854,2.604 0.5,0.323 10 false L40 2.729,2.292 3.229,2.615 0.5,0.323 10 false ANT+ 2.406,2.073 2.906,2.396 0.5,0.323 10 false 1 1.667,2.146 2.167,2.469 0.5,0.323 10 false 14 1.25,2.281 1.75,2.604 0.5,0.323 10 false ANT 0.552,2.75 2.177,3.104 1.625,0.354 10 false I49 0.552,2.917 2,3.271 1.448,0.354 10 false Motor Antenna Control Relay 0.25,4.281 2.458,4.604 2.208,0.323 10 false *: for Electric Type Antenna 6.583,2.76 6.948,3.25 0.365,0.49 10 false * 5.333,2.177 5.833,2.5 0.5,0.323 10 false 5 5.354,1.292 5.854,1.615 0.5,0.323 10 false 3

E304759E01
0.333,0.542 4.615,0.74 4.281,0.198 10 false Antenna with Holder Assembly 5.479,4.083 7.135,4.406 1.656,0.323 10 false Radio Receiver Assembly 5.948,2.281 6.885,2.635 0.938,0.354 10 false ANT 5.958,0.958 6.896,1.313 0.938,0.354 10 false MAIN 3.729,1.583 5.594,1.958 1.865,0.375 10 false Antenna Cord Sub-assembly 5.583,2.281 6.521,2.635 0.938,0.354 10 false L2 5.604,2.063 6.542,2.417 0.938,0.354 10 false 8 1.667,2.177 2.604,2.531 0.938,0.354 10 false 14 1.292,2.292 2.229,2.646 0.938,0.354 10 false ANT 0.5,2.74 1.438,3.094 0.938,0.354 10 false I49 0.5,2.917 1.938,3.313 1.438,0.396 10 false Motor Antenna Control Relay 0.146,0.115 4.427,0.365 4.281,0.25 12 false w/o CD Player: 0.385,4.302 2.583,4.729 2.198,0.427 10 false *: for Electric Type Antenna 6.604,2.958 7.01,3.51 0.406,0.552 10 false *

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.


PROCEDURE

1.CHECK IF RADIO AUTO-SEARCH FUNCTIONS PROPERLY
a.

Check the radio automatic station search function by activating it.

OK:

Automatic station search function stops on a station.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK OPTIONAL COMPONENTS
2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film or a radio antenna, are not installed.

NOTICE:

Do not remove optional components without permission of the customer.


OK:

Optional components are not installed.



Result:
Result Proceed to
OK A
NG (for Electric Type Antenna) B
NG (for Manual Type Antenna [w/ CD Player]) C
NG (for Manual Type Antenna [w/o CD Player]) D



A

REMOVE OPTIONAL COMPONENTS (SEE NOTICE ABOVE)

B

3.CHECK RADIO RECEIVER ASSEMBLY

C

4.CHECK RADIO RECEIVER ASSEMBLY

D

9.CHECK ANTENNA FOR NOISE PRODUCTION
3.CHECK RADIO RECEIVER ASSEMBLY
a.
E199600C03
1.469,0.198 1.885,0.438 0.417,0.24 1.479,1.854 1.646,1.854 1.646,1.854 1.833,1.448 true 2.031,1.146 2.229,0.719 2.229,0.719 2.385,0.719 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 1.594,0.229 2.052,0.427 0.458,0.198 10 false I49 2.427,0.604 2.813,0.865 0.385,0.26 10 false E 1.156,1.74 1.708,2.052 0.552,0.313 10 false ANT
*a Front view of wire harness connector
(to Motor Antenna Control Relay)


Disconnect the motor antenna control relay connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I48-14 (ANT) - I49-5 (E) Ignition switch ACC, radio switch on and FM or AM selected 11 to 14V



Result:
Result Proceed to
OK (w/ CD Player) A
OK (w/o CD Player) B
NG (w/ CD Player) C
NG (w/o CD Player) D



A

4.CHECK RADIO RECEIVER ASSEMBLY

B

9.CHECK ANTENNA FOR NOISE PRODUCTION

C

12.CHECK ANTENNA CORD SUB-ASSEMBLY

D

14.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MOTOR ANTENNA CONTROL RELAY)
4.CHECK RADIO RECEIVER ASSEMBLY
a.
E276819

Remove the antenna connector from the radio receiver assembly.


b.

Turn the ignition switch to ACC with the radio receiver assembly connector connected.


c.

Turn on the radio and turn into AM mode.


d.

Place a screwdriver, thin wire or other metal object on the radio receiver assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise occurs.



Result:
Proceed to
OK
NG



OK

5.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE RADIO RECEIVER ASSEMBLY

5.CHECK ANTENNA CORD SUB-ASSEMBLY
a.
E300854C01
0.594,0.729 1.063,0.969 0.469,0.24 0.656,2.708 1.125,2.948 0.469,0.24 1.115,1.583 1.292,1.583 1.292,1.583 1.573,1.219 true 0.146,0.083 0.458,0.281 0.313,0.198 10 false *a 0.177,1.906 0.49,2.104 0.313,0.198 10 false *b 0.729,0.76 1.042,0.958 0.313,0.198 10 false RA 0.74,1.448 1.26,1.708 0.521,0.26 10 false MAIN 0.833,2.74 1.146,2.938 0.313,0.198 10 false A
*a Front view of wire harness connector
(to Radio Receiver Assembly)
*b Front view of wire harness connector
(to Antenna with Holder Assembly)


Remove the antenna connector from the radio receiver assembly.


b.

Remove the antenna connector from the antenna with holder assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
RA-3 (MAIN) - A-1 Always Below 1 Ω
RA-3 (MAIN) or A-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK ANTENNA WITH HOLDER ASSEMBLY

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY

6.CHECK ANTENNA WITH HOLDER ASSEMBLY
a.

Check that the antenna with holder assembly is securely installed.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA>INSTALLATION

OK:

The antenna with holder assembly is installed properly



Result:
Proceed to
OK
NG



OK

7.CHECK ANTENNA WITH HOLDER ASSEMBLY

NG

REINSTALL ANTENNA WITH HOLDER ASSEMBLY

7.CHECK ANTENNA WITH HOLDER ASSEMBLY
a.

Replace the antenna with holder assembly and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Result Proceed to
OK A
NG (for Electric Type Antenna) B
NG (for Manual Type Antenna) C



A

END (ANTENNA WITH HOLDER ASSEMBLY IS DEFECTIVE)

B

8.CHECK MOTOR ANTENNA CONTROL RELAY

C

REPLACE RADIO RECEIVER ASSEMBLY

8.CHECK MOTOR ANTENNA CONTROL RELAY
a.

Replace the motor antenna control relay and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



OK

END (MOTOR ANTENNA CONTROL RELAY IS DEFECTIVE)

NG

REPLACE RADIO RECEIVER ASSEMBLY

9.CHECK ANTENNA FOR NOISE PRODUCTION
a.

With the ignition switch ACC, turn on the radio and choose the FM mode.


b.

Place the tip of a screwdriver on the antenna and check that noise is heard from the speakers.

OK:

Noise is heard.



Result:
Proceed to
OK
NG



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

10.CHECK RADIO RECEIVER ASSEMBLY (ANTENNA)
10.CHECK RADIO RECEIVER ASSEMBLY (ANTENNA)
a.
E108381

Remove the antenna plug from the radio receiver assembly.


b.

With the radio receiver connector connected, turn the ignition switch to ACC.


c.

Turn on the radio and choose the FM mode.


d.

Place a flat-head screwdriver or a piece of metal, such as a thin wire, on the antenna jack of the radio receiver assembly. Check that noise is heard from the speakers.

OK:

Noise is heard.



Result:
Proceed to
OK
NG



OK

11.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE RADIO RECEIVER ASSEMBLY

11.CHECK ANTENNA CORD SUB-ASSEMBLY
a.

Replace the antenna cord sub-assembly and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



OK

END (ANTENNA WITH HOLDER ASSEMBLY IS DEFECTIVE)

NG

6.CHECK ANTENNA WITH HOLDER ASSEMBLY
12.CHECK ANTENNA CORD SUB-ASSEMBLY
a.
E304755C01
0.5,0.885 1,1.156 0.5,0.271 0.646,2.521 1.146,2.792 0.5,0.271 1.948,0.979 2.198,0.771 2.198,0.771 2.385,0.771 true 0.115,0.073 0.427,0.229 0.313,0.156 10 false *a 0.083,1.865 0.396,2.021 0.313,0.156 10 false *b 0.646,0.917 0.979,1.125 0.333,0.208 10 false RA 2.458,0.646 2.969,0.885 0.51,0.24 10 false ANT+ 0.844,2.573 1.354,2.813 0.51,0.24 10 false B
*a Front view of wire harness connector
(to Radio Receiver Assembly)
*b Front view of wire harness connector
(to Instrument Panel Wire)


Remove the antenna connector from the radio receiver assembly.


b.

Remove the antenna connector from the instrument panel wire.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
RA-5 (ANT+) - B-1 Always Below 1 Ω
RA-5 (ANT+) or B-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (ANTENNA CORD SUB-ASSEMBLY - MOTOR ANTENNA CONTROL RELAY)

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (ANTENNA CORD SUB-ASSEMBLY - MOTOR ANTENNA CONTROL RELAY)
a.

Disconnect the L40 antenna cord sub-assembly connector.


b.

Disconnect the I49 motor antenna control relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L40-1 (ANT+) - I49-14 (ANT) Always Below 1 Ω
L40-1 (ANT+) or I49-14 (ANT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MOTOR ANTENNA CONTROL RELAY)
a.

Disconnect the L2 radio receiver assembly connector.


b.

Disconnect the I49 motor antenna control relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L2-8 (ANT) - I49-14 (ANT) Always Below 1 Ω
L2-8 (ANT) or I49-14 (ANT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR