67914 1.REMOVE FRONT DOOR SCUFF PLATE LH
67913 2.REMOVE FRONT DOOR SCUFF PLATE RH
62112A 3.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
62111A 4.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH
62316C 5.REMOVE FRONT DOOR REAR OPENING TRIM WEATHERSTRIP LH
62315E 6.REMOVE FRONT DOOR REAR OPENING TRIM WEATHERSTRIP RH
55356B 7.REMOVE INSTRUMENT PANEL PLATE LH
55355B 8.REMOVE INSTRUMENT PANEL PLATE RH
74617A 9.REMOVE ASSIST GRIP PLUG
74610A 10.REMOVE ASSIST GRIP SUB-ASSEMBLY
62212 11.REMOVE FRONT PILLAR GARNISH LH
62211 12.REMOVE FRONT PILLAR GARNISH RH
13.REMOVE WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH
14.REMOVE WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH
63310 15.REMOVE ROOF HEADLINING ASSEMBLY
for Model Code #J71 Series:
Remove the roof headlining assembly.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Short Body)>REMOVAL
for Model Code #J76 Series:
Partially remove the roof headlining.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Semi-long Body)>REMOVAL
It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining so that the windshield glass can be removed in a later step. Refer to the following procedure.
for Model Code #J78 Series:
Partially remove the roof headlining.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Long Body)>REMOVAL
It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining so that the windshield glass can be removed in a later step. Refer to the following procedure.
for Model Code #J79 Series:
Remove the roof headlining assembly.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Double Cab)>REMOVAL
56121 16.REMOVE WINDSHIELD WEATHERSTRIP
| *1 | Windshield Glass |
| *2 | Windshield Weatherstrip |
| *3 | Vehicle Body |
| *a | Cut |
Using a knife, cut off the windshield weatherstrip as shown in the illustration.
Be careful not to damage the vehicle body.
Pull the shaded area shown in the illustration by hand to remove the windshield weatherstrip.
Make a partial cut in the windshield weatherstrip. Then pull and remove it by hand.
56111 17.REMOVE WINDSHIELD GLASS
| *1 | No. 1 Windshield Glass Stopper |
| *2 | No. 2 Windshield Glass Stopper |
| *3 | Windshield Glass Retainer |
| *a | Plastic Sheet |
| *b | Piano Wire |
|
Protective Tape |
Apply protective tape to the outer surface of the vehicle body to prevent scratches.
From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.
Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.
When separating the glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.
To prevent the instrument panel from being scratched when removing the glass, place a plastic sheet between the piano wire and instrument panel.
| *a | Matchmarks |
Place matchmarks on the glass and vehicle body at the locations indicated in the illustration.
Matchmarks do not need to be placed if not reusing the glass.
Cut through the adhesive by pulling the piano wire around the glass.
Leave as much adhesive on the vehicle body as possible when removing the glass.
Disconnect the stoppers and retainers.
Using suction cups, remove the glass.
56115A 18.REMOVE NO. 1 WINDSHIELD GLASS STOPPER
Using a scraper, remove the No. 1 windshield glass stopper.
Be careful not to damage the windshield glass.
56116C 19.REMOVE NO. 2 WINDSHIELD GLASS STOPPER
Using a scraper, remove the No. 2 windshield glass stopper.
Be careful not to damage the windshield glass.
56114 20.REMOVE WINDSHIELD GLASS RETAINER
Using a scraper, remove the 2 windshield glass retainers.
Be careful not to damage the windshield glass.
56114A 21.REMOVE BACK WINDOW GLASS RETAINER
Using a scraper, remove the 2 back window glass retainers.
Be careful not to damage the vehicle body.
22.CLEAN VEHICLE BODY
| *1 | Vehicle Body |
|
Adhesive |
Clean and shape the contact surface of the vehicle body.
On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.
Be careful not to damage the vehicle body.
Leave as much adhesive on the vehicle body as possible.
Clean the contact surface of the vehicle body with cleaner.
Even if all the adhesive has been removed, clean the vehicle body.