Home › Drivetrain › HF1A (TRANSFER / 4WD / AWD) › TRANSFER ASSEMBLY › from 2016.08
RM25T0E _52 Drivetrain _029904 HF1A TRANSFER / 4WD / AWD _0138379 TRANSFER ASSEMBLY A

HF1A TRANSFER / 4WD / AWD  TRANSFER ASSEMBLY  REASSEMBLY  


PROCEDURE

Hide 36109C 1.INSTALL REAR TRANSFER EXTENSION HOUSING OIL SEAL

Hide 36231H 2.INSTALL FRONT TRANSFER OUTPUT SHAFT RADIAL BALL BEARING

Hide 36105A 3.INSTALL FRONT TRANSFER EXTENSION HOUSING OIL SEAL

Hide 33325B 4.INSTALL FRONT TRANSFER EXTENSION HOUSING DUST DEFLECTOR

a.
C271109

Using a plastic-faced hammer, install the front transfer extension housing dust deflector.


Hide 36104B 5.INSTALL TRANSFER OUTPUT SHAFT DUST DEFLECTOR

a.
C312853N01
0.5,1.604 0.802,1.604 true 0.969,2.385 1.521,3.125 1.521,3.125 1.74,3.125 true 0.188,1.542 0.51,1.729 0.323,0.188 10 false SST 1.844,3.021 2.167,3.208 0.323,0.188 10 false SST

Using SST and a press, install the transfer output shaft dust deflector.

SST
09316-20011  
09316-60011  (09316-00011)

NOTICE:

Press in the rear transfer output shaft dust deflector until it fits to the edge.



Hide 36239 6.INSTALL TRANSFER DRIVE CLUTCH HUB

Hide 36235 7.INSTALL TRANSFER HIGH AND LOW CLUTCH SLEEVE

a.
C271093C02
0.906,0.125 1.063,0.125 1.063,0.125 1.208,0.281 true 1.49,1.542 1.74,1.813 1.74,1.813 1.906,1.813 true 2.604,0.677 2.854,0.948 2.854,0.948 3.021,0.948 true 1.5,0.51 1.948,1.333 true 1.26,0.531 1.958,1.344 1.958,1.344 2.208,1.344 true 2.01,1.729 2.323,1.927 0.313,0.198 10 false *1 3.115,0.885 3.427,1.083 0.313,0.198 10 false *2 0.677,0.021 0.99,0.219 0.313,0.198 10 false *3 2.292,1.25 2.604,1.448 0.313,0.198 10 false *4
*1 Transfer Clutch Hub
*2 No. 2 Synchromesh Shifting Key
*3 Transfer High and Low Clutch Sleeve
*4 Transfer Synchromesh Shifting Key Spring
V100135

Front of Vehicle


Insert the transfer clutch hub and 3 No. 2 synchromesh shifting keys into the transfer high and low clutch sleeve.


b.

Install the 2 transfer synchromesh shifting key springs under the 3 No. 2 synchromesh shifting keys.

NOTICE:

Install the 2 transfer synchromesh shifting key springs positioned so that their end gaps are not in line.



Hide 36231E 8.INSTALL FRONT TRANSFER OUTPUT SHAFT NEEDLE ROLLER BEARING

a.
C271259N01
1.718,0.706 2.02,0.706 false 2.071,0.64 2.371,0.803 0.299,0.163 10 SST 1.761,0.979 1.838,0.979 false 1.838,0.979 1.838,0.706 false

Using SST and a press, press in a new front transfer output shaft needle roller bearing.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07200)


Hide 36237 9.INSTALL TRANSFER CLUTCH HUB

a.
C312892N01
0.938,2.208 1.302,2.979 1.302,2.979 1.573,2.979 true 1.646,2.896 2.104,3.094 0.458,0.198 10 false SST

Using SST and a press, install the transfer clutch hub.

SST
09316-20011  


b.
C271095

Select a snap ring that will allow minimum axial play and install it on the shaft.

Standard Thickness:
Mark Thickness
A 2.60 mm (0.1024 in.)
B 2.65 mm (0.1043 in.)
C 2.70 mm (0.1063 in.)
D 2.75 mm (0.1083 in.)
E 2.80 mm (0.1102 in.)
F 2.85 mm (0.1122 in.)
G 2.90 mm (0.1142 in.)



Hide 36242 10.INSTALL TRANSFER LOW GEAR

a.

Apply transfer oil to the transfer output shaft front needle roller bearing.


b.
C312893C01
1.115,2.24 1.385,2.5 1.385,2.5 1.51,2.5 true 0.51,1.365 0.667,1.365 0.667,1.365 0.813,1.49 true 0.958,2.01 1.375,2.24 1.375,2.24 1.5,2.24 true 2.552,1.208 2.948,1.969 2.948,1.969 3.042,1.969 true 1.615,2.406 1.958,2.583 0.344,0.177 10 false *3 0.229,1.313 0.573,1.49 0.344,0.177 10 false SST 1.573,2.146 1.917,2.323 0.344,0.177 10 false *2 3.135,1.896 3.427,2.125 0.292,0.229 10 false *1
*1 Transfer Output Shaft Front Needle Roller Bearing
*2 Transfer Output Shaft Taper Roller Bearing (Inner Race)
*3 Transfer Low Gear


Using SST and a press, install the transfer low gear and a new transfer output shaft taper roller bearing (inner race) to the output shaft assembly.

SST
09316-60011  (09316-00011)


Hide 36203 11.INSTALL TRANSFER HIGH SPEED OUTPUT GEAR SUB-ASSEMBLY

a.

Apply transfer oil to the front transfer output shaft needle roller bearing.


b.
C271097

Install the 2 pieces of the front transfer output shaft needle roller bearing and No. 1 transfer output shaft spacer to the transfer high speed output gear sub-assembly.


c.
C312896N01
0.49,1.604 0.76,1.604 false 0.125,1.521 0.448,1.698 0.323,0.177 10 false SST

Using SST and a press, install the transfer high speed output gear sub-assembly and a new transfer output shaft taper roller bearing (inner race) to the output shaft assembly.

SST
09316-60011  (09316-00011)


Hide 36245 12.INSTALL TRANSFER FRONT DRIVE GEAR PIECE

a.
C312897N01
0.885,2.542 1.469,3.021 1.469,3.021 1.656,3.021 true 1.729,2.969 2.188,3.167 0.458,0.198 10 false SST

Using SST and a press, install the transfer front drive gear piece.

SST
09316-60011  (09316-00031)


b.
C271100

Select a new snap ring that will allow minimum axial play and install it on the shaft.

Standard Thickness:
Mark Thickness
A 2.0 mm (0.0787 in.)
B 2.1 mm (0.0827 in.)
C 2.2 mm (0.0866 in.)
D 2.3 mm (0.0906 in.)
E 2.4 mm (0.0945 in.)



Hide 36203 13.INSPECT TRANSFER HIGH SPEED OUTPUT GEAR THRUST CLEARANCE

Hide 36242 14.INSPECT TRANSFER LOW GEAR THRUST CLEARANCE

Hide 36203 15.INSPECT TRANSFER HIGH SPEED OUTPUT GEAR RADIAL CLEARANCE

Hide 36242 16.INSPECT TRANSFER LOW GEAR RADIAL CLEARANCE

Hide 36221G 17.INSTALL TRANSFER ILDER GEAR BEARING (for Front Side)

a.
C312933

Install the transfer idler gear transfer oil receiver with the 3 bolts.

Torque:
7.84 N*m (80 kgf*cm, 69 in.*lbf)


b.
C312898N01
0.448,1.313 0.573,1.313 0.573,1.313 0.792,1.521 true 0.167,1.26 0.646,1.573 0.479,0.313 10 false SST

Using SST and a press, install a new transfer idler gear bearing (inner race) to the transfer idler gear.

SST
09316-60011  (09316-00011, 09316-00071)


c.
C312904N01
0.5,0.563 0.667,0.563 0.667,0.563 0.906,1.125 false 0.156,0.5 0.51,0.677 0.354,0.177 10 false SST

Using SST and a hammer, install a new transfer idler gear bearing (outer race) to the front transfer case.

SST
09316-60011  (09316-00011, 09316-00041)


Hide 36221H 18.INSTALL TRANSFER ILDER GEAR BEARING (for Rear Side)

a.
C312899N01
0.552,1.625 0.74,1.625 false 0.167,1.552 0.5,1.729 0.333,0.177 10 false SST

Using SST and a press, install a new transfer idler gear bearing (inner race) to the transfer idler gear.

SST
09316-60011  (09316-00011, 09316-00051)


b.

Install a new transfer idler gear bearing (outer race) to the rear transfer case.


Hide 36212F 19.INSTALL FRONT TRANSFER INPUT SHAFT RADIAL BALL BEARING

a.
C312900N01
0.479,1.688 0.75,1.688 false 0.125,1.604 0.479,1.792 0.354,0.188 10 false SST

Using SST and a press, install a new front transfer input shaft radial ball bearing.

SST
09316-60011  (09316-00011)


b.
C273263

Select a new snap ring that will allow minimum axial play and install it on the shaft.

Standard Thickness:
Mark Thickness
A 2.90 mm (0.1142 in.)
B 2.95 mm (0.1161 in.)
C 3.00 mm (0.1181 in.)
D 3.05 mm (0.1201 in.)
E 3.10 mm (0.1220 in.)
F 3.15 mm (0.1240 in.)



Hide 36212A 20.INSTALL TRANSFER INPUT GEAR RADIAL BALL BEARING

a.
C312901N01
0.5,1.823 0.771,1.823 false 0.177,1.74 0.49,1.906 0.313,0.167 10 false SST

Using SST and a press, install a new transfer input gear radial ball bearing.

SST
09316-60011  (09316-00011, 09316-00031)


b.
C273265

Select a new snap ring that will allow minimum axial play and install it on the shaft.

Standard Thickness:
Mark Thickness
A 2.0 mm (0.0787 in.)
B 2.1 mm (0.0827 in.)
C 2.2 mm (0.0866 in.)
D 2.3 mm (0.0906 in.)
E 2.4 mm (0.0945 in.)



Hide 36231C 21.INSTALL TRANSFER OUTPUT SHAFT TAPER ROLLER BEARING

a.
C312903N01
0.865,1.865 0.427,2.385 0.427,2.385 0.823,1.656 true 0.302,2.448 0.646,2.625 0.344,0.177 10 false SST

for Front Transfer Case Side:

Using SST and a hammer, install a new transfer output shaft taper roller bearing (outer race) to the front transfer case.

SST
09316-20011  
09316-60011  (09316-00011, 09316-00031)


b.
C271053

for Rear Transfer Case Side:

Install a new transfer output shaft taper roller bearing (outer race) to the rear transfer case.


Hide 36111B 22.INSTALL TRANSFER CASE OIL SEAL

a.

Apply MP grease to the lip of 2 new transfer case oil seals.


b.
C312905N01
0.698,1.719 0.354,2.563 0.354,2.563 0.729,1.885 true 2.156,1.927 2.156,1.563 false 0.229,2.625 0.552,2.792 0.323,0.167 10 false SST 2.927,2.125 3.208,2.323 0.281,0.198 10 false (A)

for Transfer Shift Inner Lever Shaft Side:

Using SST and a hammer, install the transfer case oil seal.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)

Drive in depth (A):

0 to 0.5 mm (0 to 0.0196 in.)


NOTICE:
·

Tap the transfer case oil seal uniformly so that the transfer case oil seal is straight.

·

Make sure the outside edge of the seal is positioned past the chamfered part.




c.
C312906N01
0.74,1.177 0.552,0.656 0.552,0.656 0.417,0.656 true 0.094,0.594 0.49,0.854 0.396,0.26 10 false SST 2.917,2.802 3.177,3 0.26,0.198 10 false (A)

for Input Shaft Side:

Using SST and a hammer, install the transfer case oil seal.

SST
09316-60011  (09316-00011, 09316-00031)

Drive in depth (A):

0 to 0.5 mm (0 to 0.0196 in.)


NOTICE:
·

Tap the transfer case oil seal uniformly so that the transfer case oil seal is straight.

·

Make sure the outside edge of the seal is positioned past the chamfered part.




Hide 36362A 23.INSTALL TRANSFER SHIFT OUTER LEVER

a.
C273274C02
1.656,1.292 1.854,1.531 1.854,1.531 2,1.531 true 1.844,1.76 1.688,1.76 1.688,1.76 1.521,1.5 true 1.458,1.906 1.292,1.906 1.292,1.906 1.188,1.604 true 1.125,0.854 1.281,0.854 1.281,0.854 1.385,1.26 true 2.063,1.458 2.344,1.667 0.281,0.208 10 false *a 0.927,0.813 1.198,1.031 0.271,0.219 10 false *3 1.896,1.677 2.156,1.896 0.26,0.219 10 false *1 1.521,1.833 1.792,2 0.271,0.167 10 false *2
*1 E-Ring
*2 Transfer Shift Inner Lever Shaft
*3 Transfer Shift Lever Inner
*a Protective Tape


Install the transfer shift lever inner to the transfer shift inner lever shaft.


b.

Using a screwdriver, install the E-ring to the transfer shift inner lever shaft.

HINT:

Tape the screwdriver tip before use.



c.
C312929C01
1.552,0.667 1.49,0.323 1.49,0.323 0.958,0.323 true 0.427,0.448 0.667,0.448 0.667,0.448 1.365,0.927 true 2.844,0.948 2.333,0.938 2.333,0.938 1.635,1.24 true 0.74,0.25 1.052,0.448 0.313,0.198 10 false *1 2.917,0.885 3.229,1.083 0.313,0.198 10 false *3 0.188,0.375 0.5,0.573 0.313,0.198 10 false *2
*1 Transfer Shift Outer Lever
*2 Transfer Shift Inner Lever Shaft
*3 Washer


Install the transfer shift inner lever shaft, washer and transfer shift outer lever to the front transfer case.


d.
C271192C01
0.845,1.583 1.050,1.749 0.205,0.166 10 *1
*1 Lever Lock Pin


Using a pin punch and hammer, tap in the lever lock pin.


e.
C312927

Install the washer and nut.

Torque:
11.76 N*m (120 kgf*cm, 9 ft.*lbf)


Hide 36312F 24.INSTALL NO. 2 TRANSFER GEAR SHIFT FORK

a.
C271211

Install the No. 2 transfer gear shift fork and shift detent ball compression spring to the transfer front drive shift fork shaft.


b.

Using a brass bar and hammer, tap in the 2 transfer gear shift fork shaft snap rings.


Hide 36236 25.INSTALL FRONT DRIVE CLUTCH SLEEVE

a.
C271041

Install the front drive clutch sleeve with the No. 2 transfer gear shift fork and transfer front drive shift fork shaft.


Hide 36311F 26.INSTALL NO. 1 TRANSFER GEAR SHIFT FORK

a.

Install the No. 1 transfer gear shift fork to the transfer high and low shift fork shaft.


b.
C271056

Using a pin punch and hammer, tap in the transfer shift fork slotted spring pin.


Hide 27.INSTALL OUTPUT SHAFT ASSEMBLY

a.
C271055C01
0.802,1.693 0.972,1.849 0.170,0.156 10 *1 3.173,0.534 3.342,0.690 0.170,0.156 10 *2 2.644,0.046 2.814,0.202 0.170,0.156 10 *3 3.097,0.625 2.793,0.625 false 2.185,0.526 2.455,0.12 false 2.455,0.12 2.587,0.12 false 1.398,1.43 1.24,1.776 false 1.24,1.776 1.034,1.776 false
*1 Idler Gear Assembly
*2 Output Shaft Assembly
*3 No. 1 Transfer Gear Shift Fork and Transfer High and Low Shift Fork Shaft


Install the idler gear assembly and output shaft assembly together with the No. 1 transfer gear shift fork and transfer high and low shift fork shaft.


Hide 28.INSTALL INPUT SHAFT ASSEMBLY

a.

Using a plastic-faced hammer, tap in the input shaft assembly.


Hide 33124E 29.INSTALL TRANSFER OIL RECEIVER PIPE

a.

for Front Transfer Extension Housing Side:

Click hereDrivetrain>HF1A (TRANSFER / 4WD / AWD)>TRANSFER CASE FRONT OIL SEAL>REPLACEMENT


b.
C312930

for Front Transfer Case Side:

i.

Clean and degrease the bolt and the installation hole.


ii.

Apply adhesive to 2 or 3 threads on the ends of the bolt.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



iii.

Install the transfer oil receiver pipe with the bolt.

Torque:
11.76 N*m (120 kgf*cm, 9 ft.*lbf)



c.
C312926

for Rear Transfer Case Side:

i.

Clean and degrease the bolt and the installation hole.


ii.

Apply adhesive to 2 or 3 threads on the ends of the bolt.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



iii.

Install the transfer oil receiver pipe with the bolt.

Torque:
18.13 N*m (185 kgf*cm, 13 ft.*lbf)



Hide 33124B 30.INSTALL REAR TRANSFER CASE OIL RECEIVER PIPE

a.
C271052

Install the rear transfer case oil receiver pipe with the bolt.

Torque:
11.76 N*m (120 kgf*cm, 9 ft.*lbf)


Hide 36112 31.INSTALL REAR TRANSFER CASE

a.

Using a scraper, clean the seal packing from the rear transfer case and front transfer case and remove any oil using a cleaning solvent.

NOTICE:

Do not scratch the installation area.



b.
C314354C01
1.281,0.635 1.396,0.344 1.396,0.344 1.625,0.344 false 1.719,0.25 2.031,0.448 0.313,0.198 10 false *a 3.021,1.24 3.24,1.448 0.219,0.208 10 false *b
*a Seal Packing
*b Seal Width 1.2 mm (0.0472 in.)


Apply seal packing to the rear transfer case as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:

Install the rear transfer case to the case within 10 minutes of application.



c.
C314085

Using a plastic-faced hammer, tap the rear transfer case to install it.


d.

Clean and degrease the bolt and the installation hole.


e.

Apply adhesive to 2 or 3 threads on the ends of the bolt.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



f.
C315891

Install the 8 bolts with the bracket.

Torque:
37.24 N*m (380 kgf*cm, 27 ft.*lbf)


g.
C312922

Using snap ring expander, install the transfer input gear shaft snap ring.


Hide 36122 32.INSTALL NO. 2 TRANSFER CASE COVER

a.

Using a scraper, clean the seal packing from the No. 2 transfer case cover and rear transfer case and remove any oil using a cleaning solvent.

NOTICE:

Do not scratch the installation area.



b.
C314355C01
0.469,0.333 0.677,0.333 0.677,0.333 0.958,0.719 true 0.24,0.25 0.552,0.448 0.313,0.198 10 false *a 3.031,1.083 3.271,1.271 0.24,0.188 10 false *b
*a Seal Packing
*b Seal Width 1.2 mm (0.0472 in.)


Apply seal packing to the rear transfer case as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:

Install the No. 2 transfer case cover to the case within 10 minutes of application.



c.

Clean and degrease the bolt and the installation hole.


d.

Apply adhesive to 2 or 3 threads on the ends of the bolt.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



e.
C357001C01
0.073,0.073 0.344,0.323 0.271,0.25 10 false *A 0.094,1.958 0.354,2.146 0.26,0.188 10 false *B
*A for H150F
*B for H152F


for H150F:

Install the No. 2 transfer case cover and bracket with the 5 bolts.

Torque:
37.24 N*m (380 kgf*cm, 27 ft.*lbf)


f.

for H152F:

Install the No. 2 transfer case cover and sensor bracket with the 5 bolts.

Torque:
37.24 N*m (380 kgf*cm, 27 ft.*lbf)


Hide 36221D 33.INSTALL TRANSFER IDLER GEAR PLATE WASHER

a.
C271204C01
2.742,0.313 2.914,0.458 0.172,0.145 10 *a
*a Dimension A


Using a vernier caliper with depth gauge, measure dimension A.

HINT:

Lightly hold down the bearing outer race in the thrust direction to eliminate any looseness before making the measurement.



b.
C271205C01
2.65,0.206 2.836,0.359 0.186,0.152 10 *a
*a Dimension B


Using a feeler gauge and precision straightedge, measure the clearance of dimension B.


c.

Calculate the required thickness of the plate washer.

Thickness:

Dimension A + Dimension B + Dimension C


Dimension C:

0.02 to 0.07 mm (0.00079 to 0.00276 in.)



d.

From the following table, select a plate washer with a thickness fitting within the range of the calculation in (c).

Standard Thickness:
Mark Thickness Mark Thickness
2 0.3 mm (0.0118 in.) 7 3.0 mm (0.118 in.)
3 0.45 mm (0.0177 in.) 8 3.2 mm (0.1260 in.)
13 0.55 mm (0.0217 in.) 9 3.4 mm (0.1339 in.)
4 2.4 mm (0.0945 in.) 10 3.6 mm (0.1417 in.)
5 2.6 mm (0.1024 in.) 11 3.8 mm (0.1496 in.)
6 2.8 mm (0.1102 in.) 12 4.0 mm (0.1575 in.)



e.
C271207C02
1.917,1.917 1.75,1.917 false 1.75,1.917 1.573,1.531 true 1.948,1.833 2.125,2 0.177,0.167 10 false *1
*1 Transfer Idler Gear Plate Washer


Install the transfer idler gear plate washer.


Hide 36231K 34.INSTALL TRANSFER OUTPUT REAR CASE PLATE WASHER

a.
C271206C01
0.666,1.052 0.854,1.205 0.187,0.153 10 *a
*a Dimension D


Using a vernier caliper with depth gauge, measure dimension D.

HINT:

Lightly hold down the bearing outer race in the thrust direction to eliminate any looseness before making the measurement.



b.

Calculate the required thickness of the plate washer.

Thickness:

Dimension D + Dimension E


Dimension E:

0.04 to 0.09 mm (0.00157 to 0.00354 in.)



c.

From the following table, select a plate washer with a thickness fitting within the range of the calculation in (a).

Standard Thickness:
Mark Thickness Mark Thickness
2 0.3 mm (0.0118 in.) 7 1.6 mm (0.0630 in.)
3 0.45 mm (0.0177 in.) 8 1.8 mm (0.0709 in.)
13 0.55 mm (0.0217 in.) 9 2.0 mm (0.0787 in.)
4 1.0 mm (0.0394 in.) 10 2.2 mm (0.0866 in.)
5 1.2 mm (0.0472 in.) 11 2.4 mm (0.0945 in.)
6 1.4 mm (0.0551 in.) 12 2.6 mm (0.1024 in.)



d.

Install the transfer output rear case plate washer.


Hide 36255 35.INSTALL NO. 1 TRANSFER OUTPUT SHAFT SPACER

a.
C315890C01
2.052,0.875 2.5,0.365 2.5,0.365 2.729,0.365 true 2.323,1.448 2.219,1.771 true 2.094,1.271 2.229,1.781 2.229,1.781 2.521,1.781 true 2.823,0.292 3.135,0.49 0.313,0.198 10 false *1 2.573,1.677 2.885,1.875 0.313,0.198 10 false *2
*1 No. 1 Transfer Output Shaft Spacer
*2 Transfer Output Rear Shaft Plate Washers


Install the No. 1 transfer output shaft spacer and 2 transfer output rear shaft plate washers.


Hide 36109B 36.INSTALL REAR TRANSFER EXTENSION HOUSING SUB-ASSEMBLY

a.

Using a scraper, clean the seal packing from the rear transfer extension housing sub-assembly and rear transfer case and remove any oil using a cleaning solvent.

NOTICE:

Do not scratch the installation area.



b.
C314356C01
1.74,0.719 1.958,0.25 1.958,0.25 2.323,0.25 true 2.417,0.177 2.729,0.375 0.313,0.198 10 false *a 2.979,1.063 3.208,1.229 0.229,0.167 10 false *b
*a Seal Packing
*b Seal Width 1.2 mm (0.0472 in.)


Apply seal packing to the rear transfer extension housing sub-assembly as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:

Install the rear transfer extension housing sub-assembly to the case within 10 minutes of application.



c.

Clean and degrease the bolt and the installation hole.


d.

Apply adhesive to 2 or 3 threads on the ends of the bolt.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



e.
C311946

w/ ABS:

i.

Install the rear transfer extension housing sub-assembly with the 7 bolts.

Torque:
37.24 N*m (380 kgf*cm, 27 ft.*lbf)



f.

w/o ABS:

i.

Install the rear transfer extension housing sub-assembly with the 9 bolts.

Torque:
37.24 N*m (380 kgf*cm, 27 ft.*lbf)



Hide 36111C 37.INSTALL TRANSFER CASE PLUG

a.
C312918

Install the transfer case plug and a new gasket to the rear transfer extension housing sub-assembly.

Torque:
37.24 N*m (380 kgf*cm, 27 ft.*lbf)


Hide 36105 38.INSTALL FRONT TRANSFER EXTENSION HOUSING SUB-ASSEMBLY

Hide 33309A 39.INSTALL DUST DEFLECTOR

a.
C312907N01
0.844,2.271 1.208,2.875 1.208,2.875 1.375,2.875 true 0.375,1.198 0.51,1.198 0.51,1.198 0.677,1.469 true 1.458,2.802 1.823,2.979 0.365,0.177 10 false SST 0.094,1.146 0.458,1.323 0.365,0.177 10 false SST

Using SST and a press, install a new dust deflector.

SST
09316-20011  
09316-60011  (09316-00011)

NOTICE:

Press in the dust deflector until it fits to the edge.



Hide 33481P 40.INSTALL TRANSFER SPEEDOMETER DRIVE GEAR

a.
C271216

Install the transfer speedometer drive gear.


Hide 33309 41.INSTALL TRANSFER OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY

Hide 36275 42.INSTALL SHIFT DETENT BALL SPRING PLUG

a.

for Front Transfer Case Side:

i.

Clean and degrease the shift detent ball spring plug and the installation hole.


ii.

Apply adhesive to 2 or 3 threads on the ends of the shift detent ball spring plug.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



iii.

Using a T40 "TORX" socket wrench, install the 2 shift detent ball spring plugs.

Torque:
18.62 N*m (190 kgf*cm, 14 ft.*lbf)


iv.
C271219C01
1.61,0.991 1.24,0.533 false 1.24,0.533 0.978,0.533 false 1.618,1.169 0.888,0.842 false 0.888,0.842 0.725,0.842 false 0.755,0.456 0.941,0.609 0.186,0.153 10 *1 0.493,0.769 0.679,0.923 0.186,0.153 10 *2
*1 Shift Detent Ball Compression Spring
*2 Shift Detent Ball


Install the shift detent ball and shift detent ball compression spring.


v.

Apply adhesive to 2 or 3 threads of the shift detent ball spring plug.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



vi.
C274097

Using a T40 "TORX" socket wrench, install the shift detent ball spring plug.

Torque:
18.62 N*m (190 kgf*cm, 14 ft.*lbf)


vii.
C273272

Install the bracket with the bolt.

Torque:
11.76 N*m (120 kgf*cm, 9 ft.*lbf)



b.

for Front Transfer Extension Housing Side:

Click hereDrivetrain>HF1A (TRANSFER / 4WD / AWD)>TRANSFER CASE FRONT OIL SEAL>REPLACEMENT


Hide 84222 43.INSTALL NO. 1 TRANSFER INDICATOR SWITCH (L4 POSITION) (w/ ABS)

Hide 36336 44.INSTALL TRANSFER HEAT INSULATOR (w/ ABS)

Hide 84222 45.INSTALL NO. 1 TRANSFER INDICATOR SWITCH (4WD Position)

Hide 46.INSTALL SPEEDOMETER DRIVEN GEAR SUB-ASSEMBLY (w/o ABS)

a.

Install the speedometer driven gear sub-assembly with the bolt.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


Hide 33403D 47.INSTALL SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY (w/ ABS)

a.

Coat a new O-ring with transfer oil and install it to the speedometer driven hole cover sub-assembly.


b.

Install the speedometer driven hole cover sub-assembly with the bolt.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


Hide 36112B 48.INSTALL REAR NO. 1 TRANSFER CASE HOSE

a.
C356989C01
0.063,0.104 0.292,0.302 0.229,0.198 10 false *A 0.073,1.948 0.313,2.167 0.24,0.219 10 false *B
*A for H150F
*B for H152F


Install the rear No. 1 transfer case hose and slide the clip to secure the hose.