Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › 2016.08–2022.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0282525 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0031  Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)  P0032  Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)  


DESCRIPTION

HINT:
·

For more information on the air fuel ratio sensor and Diesel Particulate Filter (DPF), refer to the following procedures.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION

·

This DTC is related to the air fuel ratio sensor, although the caption is the oxygen sensor.



The air fuel ratio sensor outputs a voltage* that is proportional to the air fuel ratio. The air fuel ratio sensor output voltage is used to control the air fuel ratio mixture.

The air fuel ratio sensor is located after the Diesel Particulate Filter (DPF) catalytic converter. This sensor has been developed based on the structure and technology of the air fuel ratio sensor that is used for gasoline engines. The cover for the sensor electrode has been modified to suit its application in a diesel engine. This change allows the sensor to function effectively in this DPF type diesel engine, and it also avoids problems with sensor temperature and Particulate Matter (PM).

In order to reduce PM, the ECM adjusts the air fuel ratio to a value slightly richer than that which would otherwise be used (note that this mixture is still leaner than the stoichiometric air fuel ratio). The ECM controls these adjustments on signals from the air fuel ratio sensor.

When the ECM performs PM forced regeneration (cleaning) by adding fuel using the exhaust fuel addition injector assembly, the air fuel ratio sensor feedback is used to ensure that an appropriate air fuel ratio is maintained.

*: This voltage change occurs only inside the ECM. It is not possible to measure this voltage at the sensor. The GTS can be used to monitor this voltage.

A258975E10
5.24,1.979 5.771,2.49 true 5.031,1.792 5.698,1.979 true 5.177,1.427 5.688,1.375 true 5.406,1.271 5.729,1.094 true 5.188,1.729 5.698,1.979 true 3.208,2.25 3.854,1.906 false 3.042,2.219 2.313,1.854 true 2.583,2.604 2.708,2.802 0.125,0.198 10 false A 3.271,2.604 3.396,2.781 0.125,0.177 10 false A 1.76,1.729 2.323,1.927 0.563,0.198 10 false Element 0.677,2.073 1.552,2.292 0.875,0.219 10 false Exhaust Gas 4.875,2.635 5.625,2.833 0.75,0.198 10 false A-A Section 5.719,1.896 7.146,2.115 1.427,0.219 10 false Platinum Electrode 3.906,1.813 4.323,1.99 0.417,0.177 10 false Cover 5.802,2.427 6.094,2.625 0.292,0.198 10 false Air 5.76,0.927 6.219,1.104 0.458,0.177 10 false Heater 5.729,1.26 6.927,1.646 1.198,0.385 10 false Solid Electrolyte (Zirconia Element) 0.396,4.792 1.646,5.073 1.25,0.281 10 false AF Lambda B1S1 0.375,6.104 1.604,6.271 1.229,0.167 10 false AFS Voltage B1S1 2.031,4.865 2.198,5.073 0.167,0.208 10 false 1 2.031,4.344 2.198,4.552 0.167,0.208 10 false 2 2.042,6.24 2.208,6.448 0.167,0.208 10 false 1 2.042,6.771 2.208,6.979 0.167,0.208 10 false 0 2.031,5.385 2.198,5.594 0.167,0.208 10 false 0 2.042,5.708 2.208,5.917 0.167,0.208 10 false 2 2.302,5.698 2.531,5.948 0.229,0.25 10 false (V) 2.927,6.979 3.177,7.229 0.25,0.25 10 false 10 3.24,7.073 3.594,7.323 0.354,0.25 10 false 14.5 3.688,6.979 3.938,7.229 0.25,0.25 10 false 20 4.458,6.979 4.708,7.229 0.25,0.25 10 false 30 5.229,6.979 5.479,7.229 0.25,0.25 10 false 40 5.99,6.979 6.24,7.229 0.25,0.25 10 false 50 0.146,3.313 2.406,3.49 2.26,0.177 10 false Air Fuel Ratio Displayed on Tester: 3.688,7.271 4.625,7.469 0.938,0.198 10 false Air Fuel Ratio 4.094,5 6.719,5.313 2.625,0.313 10 false AF Lambda B1S1 = Air Fuel Ratio / 14.5 2.604,8.281 3.021,8.469 0.417,0.188 10 false 0.060 4.833,8.281 5.25,8.469 0.417,0.188 10 false 0.508 5.406,8.281 5.823,8.469 0.417,0.188 10 false 0.787 5.958,8.281 6.375,8.469 0.417,0.188 10 false 0.978 6.51,8.281 6.927,8.469 0.417,0.188 10 false 1.373 4.281,8.281 4.698,8.469 0.417,0.188 10 false 0.336 3.729,8.281 4.146,8.469 0.417,0.188 10 false 0.268 3.167,8.281 3.583,8.469 0.417,0.188 10 false 0.170 2.188,8.281 2.375,8.469 0.188,0.188 10 false 0 2.115,8.729 2.448,8.917 0.333,0.188 10 false 14.5 6.031,8.729 6.365,8.917 0.333,0.188 10 false 30 2.688,8.729 3.021,8.917 0.333,0.188 10 false 15 4.906,8.729 5.24,8.917 0.333,0.188 10 false 20 6.615,8.729 6.948,8.917 0.333,0.188 10 false 50 3.802,8.729 4.135,8.917 0.333,0.188 10 false 17 3.229,8.729 3.563,8.917 0.333,0.188 10 false 16 0.375,8.729 1.313,8.927 0.938,0.198 10 false Air Fuel Ratio 4.344,8.729 4.677,8.917 0.333,0.188 10 false 18 5.479,8.729 5.813,8.917 0.333,0.188 10 false 25 1.146,8.219 1.375,8.417 0.229,0.198 10 false (V) 0.313,8.146 1.104,8.469 0.792,0.323 10 false AFS Voltage B1S1 0.333,7.615 1.135,7.948 0.802,0.333 10 false AF Lambda B1S1 2.146,7.771 2.375,7.938 0.229,0.167 10 false 1.0 2.625,7.771 2.969,7.948 0.344,0.177 10 false 1.03 3.177,7.771 3.49,7.969 0.313,0.198 10 false 1.10 3.719,7.771 4.021,7.917 0.302,0.146 10 false 1.17 4.302,7.771 4.594,7.969 0.292,0.198 10 false 1.24 4.833,7.771 5.146,7.917 0.313,0.146 10 false 1.38 5.417,7.771 5.75,7.927 0.333,0.156 10 false 1.72 5.969,7.771 6.26,7.917 0.292,0.146 10 false 2.07 6.563,7.771 6.885,7.927 0.323,0.156 10 false 3.45 0.396,9.156 0.792,9.344 0.396,0.188 10 false HINT: 0.667,9.427 6.219,9.583 5.552,0.156 10 false *1: AFS Voltage B1S1 cannot be displayed correctly when the value is 0 V or less. 1.5,8.292 1.948,8.479 0.448,0.188 10 false -0.549 1.583,8.729 1.917,8.917 0.333,0.188 10 false 12 1.542,7.781 1.854,7.948 0.313,0.167 10 false 0.83 1.438,8.063 1.635,8.25 0.198,0.188 10 false *1 2.042,3.875 2.208,4.083 0.167,0.208 10 false 3

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) Air fuel ratio sensor heater current is 0.8 A or less when the heater operates for 4 seconds (1 trip detection logic).
·

Open in air fuel ratio sensor heater circuit

·

Air fuel ratio sensor heater

·

ECM


Comes on DTC stored
P0032 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1) Air fuel ratio sensor heater current is 0.8 A or higher when the heater does not operate for 4 seconds (1 trip detection logic).
·

Short in air fuel ratio sensor heater circuit

·

Air fuel ratio sensor heater

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0031
·

AFS Voltage B1S1

·

AF Lambda B1S1

·

Exhaust Temperature B1S1


P0032

MONITOR DESCRIPTION

The inner surface of the air fuel ratio sensor element is exposed to outside air. The outer surface of the sensor element is exposed to exhaust gases. The sensor element is made of platinum coated zirconia and includes an integrated heating element. The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations of the exhaust and the outside air. The platinum coating amplifies the voltage generation. When heated, the sensor becomes very efficient. If the temperature of the exhaust is low without supplemental heating, the sensor will not generate useful voltage signals. The ECM controls the heating by using a duty-cycle to regulate the average current in the heater element. If the heater current is out of the normal range, the output signals of the sensor are inaccurate and the ECM cannot regulate the air fuel ratio properly. When the heater current is out of the normal operating range, the ECM interprets this as a malfunction and stores a DTC.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0031
·

Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.

·

Check that "Exhaust Temperature B1S1" displays 200°C (392°F) or higher using the GTS.


P0032 Ignition switch ON for 5 seconds

WIRING DIAGRAM

A394552E01
6.302,0.583 6.917,0.781 0.615,0.198 10 false HA1A 6.323,1.365 6.938,1.563 0.615,0.198 10 false A1A+ 6.302,2.875 6.917,3.073 0.615,0.198 10 false MREL 6.323,2.115 6.938,2.313 0.615,0.198 10 false A1A- 5.958,2.969 6.313,3.156 0.354,0.188 10 false A29 5.969,2.135 6.323,2.323 0.354,0.188 10 false C39 5.969,1.365 6.323,1.552 0.354,0.188 10 false C39 5.958,0.594 6.313,0.781 0.354,0.188 10 false C39 6.01,0.406 6.365,0.594 0.354,0.188 10 false 45 5.958,1.188 6.313,1.375 0.354,0.188 10 false 102 5.958,1.948 6.313,2.135 0.354,0.188 10 false 103 5.979,2.771 6.333,2.958 0.354,0.188 10 false 44 5.01,0.469 5.198,0.656 0.188,0.188 10 false 1 3.188,0.865 3.375,1.052 0.188,0.188 10 false 1 3.167,2.854 3.354,3.042 0.188,0.188 10 false 1 3.958,0.448 4.146,0.635 0.188,0.188 10 false 2 2.365,0.875 2.552,1.063 0.188,0.188 10 false 2 2.354,2.854 2.542,3.042 0.188,0.188 10 false 2 5.01,1.25 5.198,1.438 0.188,0.188 10 false 3 3.188,0.479 3.375,0.667 0.188,0.188 10 false 3 3.167,2.49 3.354,2.677 0.188,0.188 10 false 3 2.354,2.5 2.542,2.688 0.188,0.188 10 false 5 2.365,0.469 2.552,0.656 0.188,0.188 10 false 5 3.948,1.26 4.135,1.448 0.188,0.188 10 false 4 3.792,1.698 4.229,1.875 0.438,0.177 10 false C114 3.802,1.865 5.927,2.052 2.125,0.188 10 false Air Fuel Ratio Sensor 2.729,1.323 3.167,1.5 0.438,0.177 10 false A/F 1.74,0.75 2.177,0.927 0.438,0.177 10 false A/F 2.625,3.271 3.479,3.448 0.854,0.177 10 false MAIN2 1.531,2.771 2.385,2.948 0.854,0.177 10 false EFI MAIN2 0.552,1.604 1.406,1.781 0.854,0.177 10 false FL MAIN 0.688,3.01 1.542,3.188 0.854,0.177 10 false Battery 6.469,3.51 6.927,3.708 0.458,0.198 10 false ECM 4.417,3.354 5.271,3.531 0.854,0.177 10 false *: Shielded 5.469,1.031 5.656,1.219 0.188,0.188 10 false * 4.573,0.49 5.188,0.688 0.615,0.198 10 false HAF1 4.146,0.49 4.76,0.688 0.615,0.198 10 false +B 4.635,1.24 5.25,1.438 0.615,0.198 10 false AFH 4.177,1.229 4.792,1.427 0.615,0.198 10 false AF1-

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR HEATER VOLTAGE)

NG

13.REPLACE AIR FUEL RATIO SENSOR
2.CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR HEATER VOLTAGE)
a.
A394553C01
0.49,1.771 0.927,2.021 0.438,0.25 0.563,1.813 0.958,2.031 0.396,0.219 10 false C114 0.094,0.125 0.49,0.344 0.396,0.219 10 false *a
*a Front view of wire harness connector
(to Air Fuel Ratio Sensor)


Disconnect the air fuel ratio sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C114-2 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - A/F RELAY)
3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C114-1 (HA1A) - C39-45 (HA1A) Always Below 1 Ω
C114-1 (HA1A) or C39-45 (HA1A) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - A/F RELAY)
a.

Disconnect the air fuel ratio sensor connector.


b.

Remove the A/F relay from the engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C114-2 (+B) - A/F relay terminal 3 Always Below 1 Ω
C114-2 (+B) or A/F relay terminal 3 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT A/F RELAY

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.INSPECT A/F RELAY

Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (MAIN2 RELAY - ECM)

NG

10.REPLACE A/F RELAY
7.CHECK HARNESS AND CONNECTOR (MAIN2 RELAY - ECM)
a.

Remove the MAIN2 relay from the engine room relay block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MAIN2 relay terminal 1 - A29-44 (MREL) Always Below 1 Ω
MAIN2 relay terminal 1 or A29-44 (MREL) - Body ground and other terminals Always 10 kΩ or higher



Result:
Result
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (A/F RELAY AND MAIN2 RELAY - ECM)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.CHECK HARNESS AND CONNECTOR (A/F RELAY AND MAIN2 RELAY - ECM)
a.

Remove the A/F relay and MAIN2 relay from the engine room relay block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A/F relay terminal 5 - Body ground Always Below 1 Ω
MAIN2 relay terminal 5 - Body ground Always Below 1 Ω



Result:
Result
OK
NG



OK

9.REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE A/F RELAY

Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Drive the vehicle at 50 km/h (30 mph) or higher for a total of 300 seconds or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

"Exhaust Temperature B1S1" on the GTS screen should be 200°C (392°F) or higher.



i.

Confirm that the DTC is not output.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P0031 and/or P0032.


iii.

Check that STATUS is NORMAL.

HINT:
·

If STATUS is NORMAL, DTC judgment is complete and the system is determined to be normal.

·

If STATUS is INCOMPLETE or N/A, DTC judgment is incomplete. Drive the vehicle at 50 km/h (30 mph) or higher for a total of 300 seconds or more again.





Result:
Proceed to
NEXT



NEXT

END

13.REPLACE AIR FUEL RATIO SENSOR

Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED