Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2016.08
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0282525 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P2237  Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)  P2238  Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)  P2239  Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)  P2252  Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)  P2253  Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)  


DESCRIPTION

Refer to DTC P0031.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P0031

HINT:

If DTC P2237, P2238 and/or P2239 is present, refer to the DTC table for DPF system.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1) When either of the following conditions is met (1 trip detection logic):
·

An open in the circuit between terminals A1A+ and A1A-, voltage difference between terminals A1A+ and A1A- is 0.1 V or less

·

The resistance of the air fuel ratio sensor element is 250 Ω or higher for 5 seconds or more.


Main trouble area: Open in air fuel ratio sensor circuit
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

Air fuel ratio sensor heater

·

Air fuel ratio sensor heater circuit

·

ECM


Comes on DTC stored
P2238 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1) Air fuel ratio sensor circuit low (sensor 1) (1 trip detection logic). Main trouble area: Open in air fuel ratio sensor circuit
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

Air fuel ratio sensor heater

·

Air fuel ratio sensor heater circuit

·

ECM


Comes on DTC stored
P2239 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1) Air fuel ratio sensor circuit high (sensor 1) (1 trip detection logic). Main trouble area: Short in air fuel ratio sensor circuit
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

Air fuel ratio sensor heater

·

Air fuel ratio sensor heater circuit

·

ECM


Comes on DTC stored
P2252 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1) Air fuel ratio sensor circuit low (sensor 1) (1 trip detection logic). Main trouble area: Open in air fuel ratio sensor circuit
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

Air fuel ratio sensor heater

·

Air fuel ratio sensor heater circuit

·

ECM


Comes on DTC stored
P2253 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1) Air fuel ratio sensor circuit high (sensor 1) (1 trip detection logic). Main trouble area: Short in air fuel ratio sensor circuit
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

Air fuel ratio sensor heater

·

Air fuel ratio sensor heater circuit

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P2237
·

AFS Voltage B1S1

·

Exhaust Temperature B1S1


P2238
P2239
P2252
P2253

MONITOR DESCRIPTION

The air fuel ratio sensor outputs a voltage in proportion to the air fuel ratio. If impedance (alternating current resistance) or voltage output of the sensor deviates greatly from the standard range, the ECM interprets this as an open or short malfunction of the air fuel ratio sensor circuit.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2237
·

Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.

·

Check that "Exhaust Temperature B1S1" displays 200°C (392°F) or higher using the GTS.


P2238
P2239
P2252
P2253
Ignition switch ON for 7 seconds

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C114-3 (AF1+) - C39-102 (A1A+) Always Below 1 Ω
C114-4 (AF1-) - C39-103 (A1A-) Always Below 1 Ω
C114-3 (AF1+) or C39-102 (A1A+) - Body ground and other terminals Always 10 kΩ or higher
C114-4 (AF1-) or C39-103 (A1A-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REPLACE AIR FUEL RATIO SENSOR

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.REPLACE AIR FUEL RATIO SENSOR

Result:
Proceed to
NEXT



NEXT

3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Warm up the engine.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

f.

Turn the ignition switch off and wait for 30 seconds.


g.

Start the engine and turn the GTS on.


h.

Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Make sure that the exhaust gas temperature (Exhaust Temperature B1S1) is 200°C (392°F) or higher.



i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Confirm that the DTC is not output.

Powertrain > Engine > Trouble Codes
50001 61

Result:
Proceed to
OK
NG



OK

END

NG

4.REPLACE ECM
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Warm up the engine.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

f.

Turn the ignition switch off and wait for 30 seconds.


g.

Start the engine and turn the GTS on.


h.

Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Make sure that the exhaust gas temperature (Exhaust Temperature B1S1) is 200°C (392°F) or higher.



i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Confirm that the DTC is not output again.

Powertrain > Engine > Trouble Codes
50001 61

Result:
Proceed to
NEXT



NEXT

END