Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2016.08
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0282525 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P2453  Diesel Particulate Filter Pressure Sensor "A" Circuit Range/Performance  


DESCRIPTION

HINT:
·

For more information on the differential pressure sensor assembly and Diesel Particulate Filter (DPF), refer to the following procedures.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION

·

If P2453 is present, refer to the DTC chart for DPF system.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION

·

If the vacuum air hose assemblies of the differential pressure sensor assembly are incorrectly connected (crossed), the ECM interprets this as an abnormal pressure difference, DTC P2453 (Diesel Particulate Filter Pressure Sensor "A" Circuit Range/Performance) is stored and the MIL illuminates.



Refer to DTC P2454.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P2454

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2453 Diesel Particulate Filter Pressure Sensor "A" Circuit Range/Performance The output voltage from the differential pressure sensor indicates a reversal of positive and negative pressure (1 trip detection logic).
·

Incorrect vacuum transmitting hose assembly

·

Vacuum transmitting hose assembly is clogged

·

Blockage in vacuum transmitting pipe sub-assembly

·

Differential pressure sensor assembly

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P2453 DPF Differential Pressure

HINT:
·

DTC P2454 (Diesel Particulate Filter Pressure Sensor "A" Circuit Low) and/or DTC P2455 (Diesel Particulate Filter Pressure Sensor "A" Circuit High) will be stored if there is an open or short malfunction in the differential pressure sensor assembly circuit.

·

After confirming DTC P2453, check the differential pressure in "Powertrain / Engine and ECT / Data List / Diesel Exhaust / DPF Differential Pressure" using the GTS.


Reference:
Condition Differential Pressure Output Sensor Condition
Ignition switch ON Approximately 0 kPa Normal
Always -5 kPa or less or higher than 99 kPa Open or short circuit
4000 rpm (No engine load) Negative output Incorrect hose routing


MONITOR DESCRIPTION

In order to detect abnormality in the differential pressure sensor assembly, the ECM always monitors the output voltage from the sensor. When the sensor output voltage is a reversal of positive and negative pressure, the ECM interprets this as an incorrect vacuum hose arrangement of the sensor, or determines that the vacuum hoses are clogged, and illuminates the MIL.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2453 Engine is running at 4000 rpm with no load for 10 seconds or more.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P2453)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

d.

Read the DTCs.

Result:
Result Proceed to
DTC P2453 is output A
DTC P2453 and other DTCs are output B


HINT:

If any DTCs other than P2453 are output, troubleshoot those DTCs first.




A

2.CHECK CONNECTION OF AIR HOSE (DIFFERENTIAL PRESSURE SENSOR ASSEMBLY - VACUUM PIPE NO. 1, NO. 2)

B

2.CHECK CONNECTION OF AIR HOSE (DIFFERENTIAL PRESSURE SENSOR ASSEMBLY - VACUUM PIPE NO. 1, NO. 2)
a.

Check if the air hose No. 1 routing between the differential pressure sensor assembly and vacuum pipe No. 1, No. 2 is correct.

Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>DIFFERENTIAL PRESSURE SENSOR(for DPF)>INSTALLATION

A390603C01
1.125,1.615 1.333,1.188 1.333,1.188 1.406,1.188 true 4.104,2.135 4.01,2.594 4.01,2.594 4.083,2.594 true 5.385,2.042 5.542,2.375 5.542,2.375 5.615,2.375 true 5.188,1.438 4.927,0.969 4.927,0.969 4.854,0.969 true 5.667,2.302 5.979,2.458 0.313,0.156 10 false *1 4.698,0.906 5.01,1.063 0.313,0.156 10 false *2 4.135,2.521 4.448,2.677 0.313,0.156 10 false *3 1.458,1.125 1.771,1.281 0.313,0.156 10 false *4
*1 Air Hose (Downstream) *2 Air Hose (Upstream)
*3 No. 1 Air Hose *4 No. 2 Air Hose



b.

Check that there is no exhaust gas leakage between the differential pressure sensor and vacuum pipe No. 1, No. 2.


Result:
Proceed to
OK
NG



OK

3.CHECK AIR HOSE AND VACUUM PIPE

NG

8.CORRECT TO NORMAL CONNECTION
3.CHECK AIR HOSE AND VACUUM PIPE
CAUTION:

Be careful of being burned by exhaust gases during the following inspection.


a.
A390604C01
1.521,1.354 1.042,1.333 1.042,1.333 1.781,2.188 true 0.875,1.229 1.188,1.385 0.313,0.156 10 false *1
*1 Air Hose


Disconnect the both vacuum hose (upstream and downstream) from the differential pressure sensor assembly.


b.

Start the engine.


c.

Check if there are exhaust gas pulsations from both vacuum hose No. 1, No. 2 during idle.

OK:

Exhaust gas pulsation exists.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)

NG

7.REPLACE CLOGGED PARTS
4.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.

Powertrain > Engine and ECT > Data List
Tester Display
DPF Differential Pressure
50003 234 844

d.

Check that the differential pressure is as specified below.

Result
Condition Differential Pressure Output Sensor Condition
Ignition switch ON Approximately 0 kPa Normal


Result:
Proceed to
OK
NG



OK

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

5.REPLACE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY
5.REPLACE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY
a.

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

d.

Turn the ignition switch off for 30 seconds or more.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Diesel Exhaust / All Data / DPF Differential Pressure.

Powertrain > Engine and ECT > Data List
Tester Display
DPF Differential Pressure
50003 234 844

g.

Check that the differential pressure is as specified below.

HINT:
·

As long as the pipe connections are correct, the displayed pressure will not be vacuum pressure.

·

For reference result of real-vehicle check is as shown in the table below:

Condition DPF Differential Pressure
4000 rpm without load after warming up engine 0.2 kPa or more




h.

Start the engine.


i.

Engine is running at 4000 rpm with no load for 10 seconds or more.


j.

Confirm that the DTC is not output.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

ii.

Input DTC P2453.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, run the engine at 4000 rpm with no load for 10 seconds or more.



Result:
Proceed to
NEXT



NEXT

END

7.REPLACE CLOGGED PARTS
Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CORRECT TO NORMAL CONNECTION
Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED