Speeds signals are sent from the combination meter assembly to the tire pressure warning ECU and receiver.
DTC C2191/91 is stored only during the signal check.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C2174/74 | Vehicle Speed Signal Malfunction | All conditions below are met:
·
DTC C2121/21, C2122/22, C2123/23, C2124/24 and/or C2125/25 is output
·
Vehicle speed signal malfunction |
·
Combination meter assembly
·
Vehicle speed signal circuit
·
Wire harness or connector
·
Tire pressure warning ECU and receiver
·
Tire pressure warning valve and transmitter |
| C2191/91 | Vehicle Speed Signal Error (Test Mode DTC) | Test mode procedure is performed. |
·
Meter / gauge system (speed signal)
·
Vehicle speed signal circuit
·
Wire harness or connector
·
Tire pressure warning ECU and receiver |
When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.
It is necessary to perform initialization Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registration Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.
When the speedometer needle is not moving, first troubleshoot the meter/gauge system.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed | Vehicle speed reading | min.: 0 km/h (0 mph), max.: 255 km/h (158 mph) | Actual vehicle speed | Speed indicated on the combination meter assembly |
| Tester Display |
|---|
| Vehicle Speed |
Check that the values indicated on the GTS and on the combination meter assembly are the same.
Vehicle speed indicated on the GTS indicates the actual speed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON.
Perform a driving test.
Check for DTCs.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR
The time required for DTC C2174/74 to be stored is 20 minutes.
| Result | Proceed to |
|---|---|
| DTC C2174/74 is not output | A |
| DTC C2174/74 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Turn the ignition switch off.
Disconnect the S30*1, Y7*2 or U5*3 tire pressure warning ECU and receiver connector.
*1: for Single Cab
*2: for Double Cab
*3: except Single and Double Cabs
Disconnect the L25 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S30-2 (SPD) - L25-8 (+S)*1 Y7-2 (SPD) - L25-8 (+S)*2 U5-2 (SPD) - L25-8 (+S)*3 |
Always | Below 1 Ω |
| S30-2 (SPD) or L25-8 (+S) - Body ground*1 Y7-2 (SPD) or L25-8 (+S) - Body ground*2 U5-2 (SPD) or L25-8 (+S) - Body ground*3 |
Always | 10 kΩ or higher |
*1: for Single Cab
*2: for Double Cab
*3: except Single and Double Cabs
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A42 skid control ECU (brake actuator assembly) connector.
Disconnect the L25 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A42-14 (SP1) - L25-9 (SI) | Always | Below 1 Ω |
| A42-14 (SP1) or L25-9 (SI) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR
for 1VD-FTV (w/o EGR System): Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON.
Check for DTCs.
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR
for 1VD-FTV (w/o EGR System): Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC P0500 is not output | A |
| DTC P0500 is output | B |
A
B
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Replace the tire pressure warning ECU and receiver.
for Single Cab: Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER (for Pickup)>REMOVAL
for Double Cab: Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER (for Pickup)>REMOVAL
for Short Body: Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER (for Short Body)>REMOVAL
for Long Body: Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER (for Long Body)>REMOVAL
for Semi-long Body: Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER (for Semi-long Body)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Perform registration.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION
| Proceed to |
|---|
| NEXT |
NEXT
Set the tire pressure to the specified value.
Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION
Perform initialization.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / Tire Pressure Monitor / Utility / Signal Check.
| Tester Display |
|---|
| Signal Check |
Drive the vehicle at 20 km/h (12 mph) or more for 3 seconds or more to check the vehicle speed signal (C2191/91).
| Result | Proceed to |
|---|---|
| DTC C2191/91 is not cleared | A |
| DTC C2191/91 is cleared | B |
A
B