Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System) › from 2017.01
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0287798 VEHICLE STABILITY CONTROL SYSTEM(w/o Pre-collision System) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/o Pre-collision System)  VSC OFF Switch Circuit  


DESCRIPTION

The skid control ECU is connected to the combination meter assembly via CAN communication.

Pressing the VSC OFF switch turns off TRC operation, and pressing and holding this switch turns off TRC and VSC operation.


If TRC and VSC operations are turned off, the TRC OFF indicator and the VSC OFF indicator lights come on.


When the transfer is shifted to L4, VSC is prohibited and the VSC OFF indicator light turns on.


w/ Rear Differential Lock:

When the rear differential lock is in the lock state, the VSC is also prohibited and the VSC OFF indicator light turns on during operation.


WIRING DIAGRAM

C363592E01
5.604,6.823 5.917,7.021 0.313,0.198 10 false A42 5.594,6.979 7.125,7.354 1.531,0.375 10 false Skid Control ECU (Brake Actuator Assembly) 4.052,6.708 5.188,6.906 1.135,0.198 10 false VSC OFF Switch 4.042,6.552 4.375,6.719 0.333,0.167 10 false L49 0.542,7.323 2.219,7.521 1.677,0.198 10 false : CAN Communication Line 3.969,6.125 4.302,6.292 0.333,0.167 10 false 4 5.042,6.115 5.375,6.281 0.333,0.167 10 false 3 5.99,3.76 6.438,3.948 0.448,0.188 10 false EXI3* 5.99,3.49 6.531,3.698 0.542,0.208 10 false FSW+* 5.99,2.198 6.458,2.396 0.469,0.198 10 false GND1 5.99,1.146 6.458,1.344 0.469,0.198 10 false CANH 2.167,1.146 2.635,1.344 0.469,0.198 10 false CANH 5.99,0.646 6.458,0.844 0.469,0.198 10 false CANL 2.177,0.646 2.646,0.844 0.469,0.198 10 false CANL 5.625,0.938 5.844,1.167 0.219,0.229 10 false 22 5.635,0.458 5.854,0.688 0.219,0.229 10 false 10 5.646,2.083 5.865,2.313 0.219,0.229 10 false 25 5.635,3.365 5.854,3.594 0.219,0.229 10 false 23 5.677,6.104 5.896,6.333 0.219,0.229 10 false 33 5.635,3.76 5.854,3.99 0.219,0.229 10 false 11 5.979,6.219 6.458,6.438 0.479,0.219 10 false CSW 2.854,4.146 3.042,4.385 0.188,0.24 10 false V1 2.833,4.302 5.156,4.698 2.323,0.396 10 false Rear Differential Lock Position Switch (No. 4 Transfer Indicator Switch)* 0.896,5.99 2.802,6.365 1.906,0.375 10 false Differential Lock ECU (No. 2 4 Wheel Drive Control ECU)* 0.896,5.823 1.208,6.021 0.313,0.198 10 false I8 2.313,5.167 2.625,5.365 0.313,0.198 10 false RLP 2.719,5.146 3.031,5.344 0.313,0.198 10 false 2 2.885,3.771 3.073,4.01 0.188,0.24 10 false 1 4.042,3.76 4.229,4 0.188,0.24 10 false 2 0.969,2.906 2.802,3.125 1.833,0.219 10 false Combination Meter Assembly 2.656,7.313 4.365,7.521 1.708,0.208 10 false *: w/ Rear Differential Lock 2.719,0.427 2.938,0.656 0.219,0.229 10 false 14 2.74,0.927 2.958,1.156 0.219,0.229 10 false 13 2.042,2.375 2.573,2.583 0.531,0.208 10 false RRSW* 2.74,2.146 3.052,2.365 0.313,0.219 10 false 17 2.688,0.656 2.99,0.896 0.302,0.24 10 false L26 2.698,1.156 3.01,1.427 0.313,0.271 10 false L26 2.698,2.375 3.01,2.646 0.313,0.271 10 false L25

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>CALIBRATION

·

As there may be malfunctions in the transfer system related to when the transfer operates in L4, check the transfer system first.

Click hereDrivetrain>HF1A (TRANSFER / 4WD / AWD)>TRANSFER SYSTEM>PROBLEM SYMPTOMS TABLE



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM

Result:
Proceed to
DTC is not output
DTC is output



DTC is not output

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

DTC is output

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (TRC/VSC OFF MODE)

NG

CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY

3.READ VALUE USING GTS (TRC/VSC OFF MODE)
a.

Reconnect the A42 skid control ECU (brake actuator assembly) connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
TRC/VSC Off Mode TRC/VSC off mode Normal, TRC OFF or VSC OFF Normal: Normal mode
TRC OFF: TRC off mode
VSC OFF: VSC off mode
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
TRC/VSC Off Mode
50003 105 282

e.

Check that the indicator light and mode condition on the GTS change according to VSC OFF switch operation.

Standard:
Switch Operation Mode Condition Display TRC OFF Indicator Light VSC OFF Indicator Light
Not pressed Normal Does not come on Does not come on
Pressing the VSC OFF switch TRC OFF Comes on Does not come on
Pressing and holding the VSC OFF switch VSC OFF Comes on Comes on



Result:
Result Proceed to
Indicator light and mode condition display do not change. A
Mode condition display is normal, but indicator light does not change. B
Indicator light and mode condition display are normal. C



A

4.PERFORM ACTIVE TEST USING GTS (TRC(TRAC) OFF INDICATOR LIGHT AND VSC OFF INDICATOR LIGHT)

B

C

4.PERFORM ACTIVE TEST USING GTS (TRC(TRAC) OFF INDICATOR LIGHT AND VSC OFF INDICATOR LIGHT)
a.

Select the Active Test on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
TRC(TRAC) OFF Indicator Light TRC OFF indicator light Indicator light ON/OFF Observe combination meter assembly
Vehicle condition: Vehicle stopped
VSC OFF Indicator Light VSC OFF indicator light Indicator light ON/OFF Observe combination meter assembly
Vehicle condition: Vehicle stopped
Chassis > ABS/VSC/TRC > Active Test
Tester Display
TRC(TRAC) OFF Indicator Light
50004 105 78
Chassis > ABS/VSC/TRC > Active Test
Tester Display
VSC OFF Indicator Light
50004 105 79

b.

Check the TRC OFF indicator light and VSC OFF indicator light on the combination meter assembly turn ON or OFF in accordance with the GTS operation.

OK:

The TRC OFF indicator light and VSC OFF indicator light turn ON or OFF in accordance with the GTS operation.



Result:
Proceed to
OK (w/ Rear Differential Lock)
OK (w/o Rear Differential Lock)
NG



OK (w/ Rear Differential Lock)

5.CHECK HARNESS AND CONNECTOR (EXI3 TERMINAL)

OK (w/o Rear Differential Lock)

6.INSPECT VSC OFF SWITCH

NG

10.INSPECT COMBINATION METER ASSEMBLY
5.CHECK HARNESS AND CONNECTOR (EXI3 TERMINAL)
a.

Turn the ignition switch to ON.


b.

Rear differential switch ON.


c.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


d.
C363591C04
1.521,0.125 1.917,0.354 0.396,0.229 2.271,0.875 2.344,0.24 2.344,0.24 2.542,0.24 true 1.594,0.156 1.906,0.354 0.313,0.198 10 false A42 2.583,0.156 2.979,0.354 0.396,0.198 10 false EXI3
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A42-11 (EXI3) - Body ground
·

Ignition switch ON

·

Rear differential switch ON


Below 1 Ω


Result:
Proceed to
OK
NG




OK

6.INSPECT VSC OFF SWITCH

NG

8.CHECK HARNESS AND CONNECTOR (EXI3/FSW+ TERMINAL CIRCUIT)
6.INSPECT VSC OFF SWITCH
a.

Turn the ignition switch off.



c.

Inspect the VSC OFF switch.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH (w/ VSC)>INSPECTION

OK:

The VSC OFF switch operates normally.



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VSC OFF SWITCH)

NG

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VSC OFF SWITCH)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-33 (CSW) - L49-3 Always Below 1 Ω
A42-33 (CSW) or L49-3 - Body ground Always 10 kΩ or higher
L49-4 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (EXI3/FSW+ TERMINAL CIRCUIT)
a.

Turn the ignition switch off.


b.

Disconnect the L25 combination meter assembly connector.


c.

Disconnect the V1 rear differential lock position switch (No. 4 transfer indicator switch) connector.


d.

Disconnect the I8 differential lock ECU (No. 2 4 wheel drive control ECU) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-11 (EXI3) - V1-2 Always Below 1 Ω
A42-11 (EXI3) or V1-2 - Body ground Always 10 kΩ or higher
A42-11 (EXI3) - L25-17 (RRSW) Always Below 1 Ω
A42-11 (EXI3) or L25-17 (RRSW) - Body ground Always 10 kΩ or higher
A42-11 (EXI3) - I8-2 (RLP) Always Below 1 Ω
A42-11 (EXI3) or I8-2 (RLP) - Body ground Always 10 kΩ or higher
A42-23 (FSW+) - V1-2 Always Below 1 Ω
A42-23 (FSW+) or V1-2 - Body ground Always 10 kΩ or higher
A42-23 (FSW+) - L25-17 (RRSW) Always Below 1 Ω
A42-23 (FSW+) or L25-17 (RRSW) - Body ground Always 10 kΩ or higher
A42-23 (FSW+) - I8-2 (RLP) Always Below 1 Ω
A42-23 (FSW+) or I8-2 (RLP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT NO. 4 TRANSFER INDICATOR SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT NO. 4 TRANSFER INDICATOR SWITCH
a.

Remove the rear differential lock position switch (No. 4 transfer indicator switch).

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL LOCK POSITION SWITCH(w/ Differential Lock)>REMOVAL


b.

Inspect the rear differential lock position switch (No. 4 transfer indicator switch).

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL LOCK POSITION SWITCH(w/ Differential Lock)>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

10.INSPECT COMBINATION METER ASSEMBLY
a.

Turn the ignition switch off.


b.

Perform the Active Test of the combination meter assembly using the GTS.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display
VSC TRC Indicator
50004 122 102
Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. VSC OFF
50004 122 94

c.

Check the combination meter assembly.

OK:

The TRC OFF indicator light turns on or off in accordance with the GTS.



Result:
Proceed to
OK
NG



OK

NG