Home › Engine / Hybrid System › 1VD-FTV (INTAKE / EXHAUST) › INTAKE MANIFOLD (w/o DPF) › 2017.01–2017.09
RM25T0E _51 Engine / Hybrid System _029894 1VD-FTV INTAKE / EXHAUST _0136508 INTAKE MANIFOLD(w/o DPF) A

1VD-FTV INTAKE / EXHAUST  INTAKE MANIFOLD(w/o DPF)  INSTALLATION  


PROCEDURE

Hide 17112 1.INSTALL NO. 2 INTAKE MANIFOLD

a.

Install a new gasket and the No. 2 intake manifold with the 9 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 17111 2.INSTALL NO. 1 INTAKE MANIFOLD

a.

Install a new gasket and the No. 1 intake manifold with the 8 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 3.INSTALL STARTER HOSE BRACKET SUB-ASSEMBLY

Hide 16268 4.INSTALL NO. 1 WATER BY-PASS PIPE

a.

Install a new gasket and the No. 1 water by-pass pipe with the union bolt.

Torque:
58.8 N*m (600 kgf*cm, 43 ft.*lbf)


b.

Install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 9.INSTALL EGR VALVE WITH EGR COOLER (w/ EGR System)

Hide 25602 10.INSTALL NO. 2 EGR PIPE SUB-ASSEMBLY (w/ EGR System)

Hide 25601 11.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY (w/ EGR System)

Hide 17114D 13.INSTALL NO. 3 INTAKE MANIFOLD

A164778N01
1.594,0.698 1.75,0.875 0.156,0.177 10 true A 2.635,0.156 2.802,0.333 0.167,0.177 10 true B 1.698,1.229 1.854,1.396 0.156,0.167 10 true A 2.76,0.427 2.927,0.604 0.167,0.177 10 true B 2.031,0.323 2.198,0.5 0.167,0.177 10 true B 1.073,0.781 1.24,0.958 0.167,0.177 10 true B 0.885,0.396 1.052,0.573 0.167,0.177 10 true B 0.198,0.125 0.365,0.302 0.167,0.177 10 false B 0.313,0.635 0.438,0.844 0.125,0.208 10 true B 2.875,1.604 3.042,1.781 0.167,0.177 10 true B 2.719,1.792 2.885,1.969 0.167,0.177 10 true B 1.615,1.531 1.75,1.688 0.135,0.156 10 true B 1.417,1.583 1.552,1.74 0.135,0.156 10 true B 0.167,1.823 0.302,1.979 0.135,0.156 10 true B 0.563,1.167 0.698,1.323 0.135,0.156 10 true B 0.823,1.583 0.958,1.74 0.135,0.156 10 true B

a.

Install a new gasket to the No. 1 intake manifold and a new gasket to the No. 2 intake manifold.


b.

Install the No. 3 intake manifold with the 16 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

Bolt length:
Item Length
Bolt A 70 mm (2.76 in.)
Bolt B 25 mm (0.984 in.)



Hide 17113 14.INSTALL INTAKE PIPE

a.

w/ EGR System:

i.

Install a new gasket.


ii.

Install the intake pipe with the 4 bolts and 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)



b.

w/o EGR System:

i.

Install a new gasket.


ii.

Install the intake pipe with the 4 bolts and 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)



Hide 25614 15.INSTALL NO. 4 EGR PIPE (w/ EGR System)

a.

Install 2 new gaskets to the pipe.


b.

Install the No. 4 EGR pipe with the 4 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 23801L 16.INSTALL FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY

A163375C01
1.302,0.417 0.615,0.646 0.615,0.646 1.302,0.49 true 0.438,0.542 0.656,0.75 0.219,0.208 10 true *a
*a Marking


a.

Connect the fuel pump hose and No. 1 fuel hose to the fuel filter to injection pump fuel pipe sub-assembly, and slide the clamp to secure the hoses.

HINT:
·

Align the markings and connect the hose.

·

Align the pinching portion of the clamp with the hose marking and connect the hose.




b.

Install the fuel filter to injection pump fuel pipe sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 23705 19.INSTALL NO. 5 INJECTION PIPE SUB-ASSEMBLY

Hide 23805B 20.INSTALL NO. 5 FUEL PIPE SUB-ASSEMBLY

a.
A163374C01
1.458,0.802 1.906,0.146 true 1.906,0.146 1.583,0.792 true 1.917,0.042 2.115,0.208 0.198,0.167 10 true *a
*a Marking


Install a new gasket and the No. 5 fuel pipe sub-assembly with the union bolt.

Torque:
12.3 N*m (125 kgf*cm, 9 ft.*lbf)


b.

Install the nut to the No. 5 fuel pipe sub-assembly.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Install the No. 2 injection pipe clamp with the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.

Connect the No. 3 fuel hose to the No. 5 fuel pipe sub-assembly, and slide the clamp to secure the hose.

HINT:
·

Align the markings and connect the No. 3 fuel hose.

·

Align the pinching portion of the clamp with the No. 3 fuel hose marking and connect the No. 3 fuel hose.




Hide 23706 22.INSTALL NO. 6 INJECTION PIPE SUB-ASSEMBLY

a.

w/ EGR System:

i.

When installing a new No. 6 injection pipe, tighten the union nuts by hand until they contact the common rail.

HINT:

Move the pipe vertically and horizontally and check that the pipe dose not rattle and the union nuts are securely installed. Afterward, tighten once more by hand, and then check that the parts are secure.



ii.
A329093C01
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Fulcrum length


Using a 17 mm union nut wrench, tighten the union nuts.

Torque:
Specified tightening torque:

34 N*m (347 kgf*cm, 25 ft.*lbf)


NOTICE:

Make sure there is no damage or foreign matter on the seal surfaces.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 29.1 N*m (297 kgf*cm, 21 ft.*lbf)

·

After installation, check that the injection pipe is free from dents and damage, and the pipe is not deformed.




iii.

Install the 2 No. 2 injection pipe clamps with the 2 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)



b.

w/o EGR System:

i.

When installing a new No. 6 injection pipe, tighten the union nuts by hand until they contact the common rail.

HINT:

Move the pipe vertically and horizontally and check that the pipe dose not rattle and the union nuts are securely installed. Afterward, tighten once more by hand, and then check that the parts are secure.



ii.
A329093C01
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Fulcrum length


Using a 17 mm union nut wrench, tighten the union nuts.

Torque:
Specified tightening torque:

34 N*m (347 kgf*cm, 25 ft.*lbf)


NOTICE:

Make sure there is no damage or foreign matter on the seal surfaces.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 29.1 N*m (297 kgf*cm, 21 ft.*lbf)

·

After installation, check that the injection pipe is free from dents and damage, and the pipe is not deformed.




iii.

Install the No. 2 injection pipe clamp with the nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


iv.

Install the No. 6 injection pipe sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 89 in.*lbf)



Hide 23.INSTALL INJECTION PIPE LH

a.

When installing 4 new injection pipes, tighten the union nuts by hand until they contact the common rail assembly and injector assembly.

HINT:

Move the pipe vertically and horizontally and check that the pipe dose not rattle and the union nuts are securely installed. Afterward, tighten once more by hand, and then check that the parts are secure.



b.
A329093C01
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Fulcrum length


Using 17 mm union nut wrench, tighten the union nuts.

Torque:
Specified tightening torque:

34 N*m (347 kgf*cm, 25 ft.*lbf)


NOTICE:

Make sure there is no damage or foreign matter on the seal surfaces.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 29.1 N*m (297 kgf*cm, 21 ft.*lbf)

·

After installation, check that the injection pipe is free from dents and damage, and the pipe is not deformed.




Hide 24.INSTALL INJECTION PIPE RH

a.

When installing 4 new injection pipes, tighten the union nuts by hand until they contact the common rail assembly and injector assembly.

HINT:

Move the pipe vertically and horizontally and check that the pipe dose not rattle and the union nuts are securely installed. Afterward, tighten once more by hand, and then check that the parts are secure.



b.
A329093C01
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Fulcrum length


Using a 17 mm union nut wrench, tighten the union nuts.

Torque:
Specified tightening torque:

34 N*m (347 kgf*cm, 25 ft.*lbf)


NOTICE:

Make sure there is no damage or foreign matter on the seal surfaces.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 29.1 N*m (297 kgf*cm, 21 ft.*lbf)

·

After installation, check that the injection pipe is free from dents and damage, and the pipe is not deformed.




Hide 17947B 25.INSTALL NO. 3 INTERCOOLER SUPPORT BRACKET

a.

Install the No. 3 intercooler support bracket with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 23265 26.INSTALL NO. 1 GAS FILTER

a.

Install the No. 1 gas filter.


b.

Connect the hose to the intake pipe.


Hide 82121 27.CONNECT ENGINE WIRE

a.

RH Side:

i.

Connect the engine wire with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.

Attach the 2 clamps.


iii.

Connect the 4 fuel injector connectors.


iv.

Connect the 2 connectors.



b.

LH Side:

i.

Connect the engine wire with the 7 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.

Connect the 4 fuel injector connectors.


iii.

Connect the 2 connectors.



c.

Rear Side:

i.

Connect the 2 wire harness brackets with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.

Connect the 2 ground wires with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


iii.

Attach the clamp to the No. 3 intercooler support bracket.



Hide 23243C 28.INSTALL FUEL PUMP MOTOR WIRE

a.

Connect the fuel pump motor connector.


b.

Install the bracket with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16278 29.INSTALL NO. 2 WATER BY-PASS PIPE

A165810C01
2.417,1.229 2.198,1.844 2.198,1.844 2.49,1.281 true 2.104,1.854 2.354,2.094 0.25,0.24 10 true *a
*a Marking


a.

Install the No. 2 water by-pass pipe, and slide the clamp to secure the hose.

HINT:
·

Align the markings and connect the hose.

·

Align the pinching portion of the clamp with the hose marking and connect the hose.




Hide 16288 30.INSTALL NO. 4 WATER BY-PASS PIPE

a.

w/ EGR System:

i.

Connect the inlet water hose, No. 4 water by-pass hose and No. 7 water by-pass hose to the No. 4 water by-pass pipe, and slide the clamp to secure the hoses.


ii.

Install the No. 4 water by-pass pipe with the 2 bolts and nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:

Tighten the 2 bolts first.




b.

w/o EGR System:

i.

Connect the inlet water hose and No. 7 water by-pass hose to the No. 4 water by-pass pipe, and slide the clamp to secure the hoses.


ii.

Install the No. 4 water by-pass pipe with the 2 bolts and nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:

Tighten the 2 bolts first.




Hide 25850 31.INSTALL ELECTRIC VACUUM REGULATING VALVE ASSEMBLY

Hide 44761 32.INSTALL VACUUM PUMP TO CONNECTOR TUBE

A328274N01
1.625,0.458 1.781,0.646 0.156,0.188 10 true A 2.188,1.198 2.344,1.396 0.156,0.198 10 true B 1.313,1.115 1.469,1.281 0.156,0.167 10 true B

a.

Install the vacuum pump to connector tube with the 3 bolts.

Torque:
for bolt A : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for bolt B : 10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the union to connector tube hose to the vacuum pump to connector tube, and slide the clamp to secure the hose.


c.

Connect the engine wire clamp to the vacuum pump to connector tube.


Hide 82122 33.CONNECT NO. 2 ENGINE WIRE

a.

Connect the No. 2 engine wire with the 2 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 44769 34.INSTALL VACUUM RESERVOIR CONNECT TUBE

A163369C01
0.76,0.354 0.948,0.552 0.188,0.198 10 false *a 1.781,0.927 1.938,1.115 0.156,0.188 10 true A 2.51,1.052 2.667,1.24 0.156,0.188 10 true B 1.198,1.271 1.365,1.448 0.167,0.177 10 true B 1.698,1.229 1.854,1.417 0.156,0.188 10 true B
*a Upper


a.

Install the vacuum reservoir connect tube with the 4 bolts.

Torque:
for bolt A : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for bolt B : 10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the 2 vacuum hoses, and slide the clamp to secure the hose.

HINT:
·

Align the hose markings as shown in the illustration.

·

Align the pinching portion of the clamp with the hose marking and connect the hose.




Hide 23804D 35.INSTALL NO. 4 FUEL PIPE SUB-ASSEMBLY

A163371C01
2.302,0.333 2.5,0.521 0.198,0.188 10 false *a 0.844,3 1.042,3.188 0.198,0.188 10 false B 0.719,2.26 0.896,2.438 0.177,0.177 10 false A
*a Upper


a.

Install the No. 4 fuel pipe sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the No. 2 fuel hose to the No. 4 fuel pipe sub-assembly, and slide the clamp to secure the hose.

Standard Distance:
Distance Specified Condition
A 2.0 to 7.0 mm (0.0787 to 0.276 in.)
B 0 to 3.0 mm (0 to 0.118 in.)


HINT:
·

Install the hose so that its direction and position are as shown in the illustration.

·

Install the clamp so that its direction and position are as shown in the illustration.




Hide 23284A 36.INSTALL NO. 5 FUEL HOSE

A163370C01
2.51,0.521 2.698,0.708 0.188,0.188 10 false *a 2.917,0.177 3.125,0.365 0.208,0.188 10 false *b 0.51,1.24 0.698,1.438 0.188,0.198 10 false *b
*a Front
*b Upper


a.

Install the No. 5 fuel hose to the No. 5 fuel pipe and No. 4 fuel pipe, and slide the 2 clamps to secure the hose.

HINT:
·

Align the hose markings as shown in the illustration.

·

Align the pinching portion of the clamp with the hose marking as shown in the illustration and connect the hose.




Hide 16267 37.CONNECT NO. 2 AND NO. 3 WATER BY-PASS HOSES

A163368C01
2.021,0.917 2.021,1.521 2.021,1.521 2.625,0.896 true 1.802,0.698 1.854,0.385 1.854,0.385 1.99,0.385 false 2.875,0.281 2.719,0.281 2.719,0.281 2.469,0.698 true 2.031,0.292 2.271,0.521 0.24,0.229 10 true *a 1.958,1.531 2.188,1.76 0.229,0.229 10 true *a 2.917,0.188 3.156,0.417 0.24,0.229 10 true *a
*a Marking


a.

Connect the No. 2 water by-pass hose and No. 3 water by-pass hose, and slide the 2 clamps to secure the hoses.

HINT:
·

Align the markings and connect the hose.

·

Align the pinching portion of the clamp with the hose marking and connect the hose.




Hide 12142 38.INSTALL NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the No. 2 engine oil level dipstick guide.


c.

Install the No. 2 engine oil level dipstick guide with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 15301 39.INSTALL ENGINE OIL LEVEL DIPSTICK

Hide 26100G 40.INSTALL DIESEL THROTTLE BODY ASSEMBLY (for Bank 2)

Hide 26100G 41.INSTALL DIESEL THROTTLE BODY ASSEMBLY (for Bank 1)

Hide 17940D 44.INSTALL INTERCOOLER ASSEMBLY

Hide 47.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 51442 51.INSTALL NO. 2 ENGINE UNDER COVER