Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o EGR System) › 2017.01–2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0309414 ECD SYSTEM(w/o EGR System) J

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR System)  White Smoke Emitted  


DESCRIPTION

Faults and Symptoms of Common Rail Diesel Components


a.

Engine Control

Turbocharger System
Main fault Turbocharger sub-assembly malfunction (compressor side seal ring, turbine side seal ring, shaft, oil drain)
Symptoms White smoke
Excessive oil consumption

Glow System
Main fault Glow system malfunction
Symptoms Difficult to start, rough idle, knocking, white smoke (when cold)
Diagnostic Point
·

Measure the resistance of the glow plug

·

Check the glow plug indicator light



Engine
Main fault Loss of compression
Symptoms Rough idle (constant lack of power)
Data List Engine Speed of Cyl #1 to #8
·

When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder (approx. 100 rpm more than the other cylinders) that cylinder may lose compression.


Injection Feedback Val #1 to #8
·

If Injection Feedback Val #1 to #4 is more than 3 mm3/st, the cylinder may have a fault.




b.

Diesel Injection

Fuel injector
Main fault Blockage
Symptoms Rough idle, lack of power, black smoke, white smoke, knocking
Data List Injection Feedback Val #1 to #8
·

When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder. Injection Feedback Val #1 to #8 can be read after idling for 1 minute with the engine warmed up (the engine coolant temperature is higher than 75°C (167°F)).



HINT:

When the sliding resistance of the internal parts of the injector assemblies (nozzle needle, control valve) has increased due to internal contamination, injection quantity will increase at high fuel press due to a delay in fuel injector closure.


Injector Driver
Main fault Circuit fault: The fuel injector does not open.
Symptoms Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking
Data List Same as fuel injector
Diagnostic Trouble Code When the injector driver has a fault, some DTCs may be stored.

Poor Quality Fuel
Main fault -
Symptoms Difficult to start, rough idle (especially when cold)



CAUTION / NOTICE / HINT

NOTICE:

After replacing an fuel injector, the ECM requires registration (Click here Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION).


Explanation of Symptom


White Smoke When the engine is misfiring, any fuel that has been injected but remains unburned is emitted as white smoke.
Turbocharger internal oil leak (Click here (Click here))
If oil leak occurs from turbine side seal, large amount of white smoke will be emitted from the exhaust pipe.
Internal oil leak is not visible from the outside of the turbocharger sub-assembly.


PROCEDURE

1.CONFIRM CONDITIONS PRESENT WHEN WHITE SMOKE APPEARED WITH CUSTOMER
a.

Ask the customer about the conditions when the white smoke was emitted.

- What were the driving conditions when the white smoke was generated.

- Is the white smoke constantly emitted, or only occasionally?

- Does the white smoke occur only when the vehicle is cold, or when the vehicle is both cold and hot?

- Is the white smoke emitted just after starting the vehicle only, or does it continue while the vehicle is idling?


b.

Determine the symptoms of the problem to narrow down the possible causes.


Result:
Proceed to
NEXT



NEXT

2.READ OUTPUT DTCS (RELATING TO ENGINE)
2.READ OUTPUT DTCS (RELATING TO ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Troubles.


d.

Read pending DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 61
Result:
Result Proceed to
No DTCs are output A
Engine related DTCs are output B




A

3.CHECK WHEN WHITE SMOKE IS EMITTED

B

3.CHECK WHEN WHITE SMOKE IS EMITTED
a.

Start the engine.


b.

Fully depress the accelerator pedal, and then release it.


c.
A221583C03
0.291,0.017 0.94,0.228 0.649,0.212 10 *a
*a Example


Check whether white smoke is emitted or not when racing the engine.

NOTICE:

Be sure not to check for white smoke indoors.


HINT:
·

If the white smoke is emitted only just after engine start and disappears later, the smoke is not from the turbocharger.

·

If the turbocharger is the cause of the problem, regardless of whether the engine is cold or warmed up, there will be a large amount of white smoke to the extent that visibility is obstructed for a few meters in the area of the smoke (as shown in the illustration).

·

Depending on whether there is oil mixed with the fuel, or whether there is unburned fuel present, the smell of the exhaust gas differs. When oil is mixed in, the exhaust gas smells such as burning oil.

·

When continuously traveling with the engine close to idle for 1 hour or more, such as when in heavy traffic, unburned fuel accumulates in the catalytic converter, and can produce white smoke when accelerating.



Result:
Result Proceed to
White smoke is emitted just after engine start only A
White smoke is always and continuously emitted B
There is oil on the exhaust pipe, etc.
HINT:

The oil on the exhaust pipe may be from the transmission, etc.


C




A

4.CHECK TEMPERATURE WHEN WHITE SMOKE IS EMITTED

B

24.CHECK IDLING CONDITION

C

25.CHECK FOR OIL LEAKAGE
4.CHECK TEMPERATURE WHEN WHITE SMOKE IS EMITTED
a.

Check whether the white smoke is emitted only when the engine coolant temperature is below 0°C (32°F).

HINT:
·

If so, the smoke is not from the turbocharger and may be the smoke of unburned fuel.

·

If misfiring occurs, unburned fuel is emitted.



Result:
Result Proceed to
White smoke is emitted when the temperature is below 0°C (32°F) A
White smoke is emitted regardless of temperature B




A

5.INSPECT GLOW PLUG (RESISTANCE)

B

6.READ VALUE USING GTS (FUEL PRESS AND TARGET COMMON RAIL PRESSURE)
5.INSPECT GLOW PLUG (RESISTANCE)

Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (FUEL PRESS AND TARGET COMMON RAIL PRESSURE)

NG

6.READ VALUE USING GTS (FUEL PRESS AND TARGET COMMON RAIL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press and Target Common Rail Pressure.

Powertrain > Engine and ECT > Data List
Tester Display
Target Common Rail Pressure
Fuel Press
50003 61 706,54

e.

Take a snapshot with the GTS.


f.

Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when racing the engine with the accelerator pedal fully depressed.

Result:
Result Proceed to
Fuel Press is within 5000 kPa of Target Common Rail Pressure A
Except above B


HINT:
·

"Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.

·

"Fuel Press" is the actual fuel pressure.





A

7.CHECK INJECTOR COMPENSATION CODE

B

18.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP ASSEMBLY
7.CHECK INJECTOR COMPENSATION CODE
a.

Read the injector compensation codes.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION

OK:

Compensation codes stored in the ECM match the compensation codes of the installed injector assemblies.



Result:
Proceed to
OK
NG



OK

8.READ VALUE USING GTS (INJECTION FEEDBACK VAL #1 TO #8 AND INJECTION VOLUME)

NG

8.READ VALUE USING GTS (INJECTION FEEDBACK VAL #1 TO #8 AND INJECTION VOLUME)
a.

Check Injection Feedback Val #1 to #8 and Injection Volume in the snapshot taken after the engine is warmed up and idled for 1 minute with the A/C off.

HINT:

The engine coolant temperature is 75°C (167°F) or higher.


Result:
Result Proceed to
Injection Feedback Val #1 to #8 are -3.0 to 3.0 mm3/st or less and Injection Volume is 3.0 to 10 mm3/st A
Other than above B




A

9.CHECK ENGINE ASSEMBLY

B

10.CHECK WHEN WHITE SMOKE IS EMITTED
9.CHECK ENGINE ASSEMBLY
a.

Inspect the engine to see whether white smoke is being emitted due to defects in the engine itself.

i.

Check for oil leaking into the combustion chamber due to a faulty valve stem oil seal.


ii.

Check for oil leaking into the combustion chamber due to a faulty fuel injector nozzle sheet.


iii.

Check for low compression.

HINT:

If the engine runs too rough, Injection Feedback Val #1 to #8 cannot be corrected and the readout will (incorrectly) show that Injection Feedback Val #1 to #8 are within the normal range.


HINT:

If defects are found, perform repairs, and then check that the symptoms are no longer present.




Result:
Proceed to
NEXT



NEXT

END

10.CHECK WHEN WHITE SMOKE IS EMITTED
a.
A221583C01
0.291,0.017 0.94,0.228 0.649,0.212 10 *a
*a Example


Start the engine.


b.

Fully depress the accelerator pedal, and then release it.


c.

Check whether white smoke is emitted or not when racing the engine.

NOTICE:

Be sure not to check for white smoke indoors.


Result:
Result Proceed to
White smoke is not emitted A
White smoke is emitted B




A

END

B

11.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT CYLINDER FUEL CUT)
11.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT CYLINDER FUEL CUT)
HINT:

Use this Active Test to determine the malfunctioning cylinder.


a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Select Cylinder Fuel Cut.

HINT:

If the engine idle speed does not change when an fuel injector is disabled, the cylinder being tested is malfunctioning. Record any malfunctioning cylinders.


Powertrain > Engine and ECT > Active Test
Tester Display
Control the Select Cylinder Fuel Cut
50004 61 231

Result:
Proceed to
NEXT



NEXT

12.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)
12.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)
HINT:

Use this Active Test to help determine whether a cylinder has compression loss or not.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #8.

Powertrain > Engine and ECT > Active Test
Active Test Display
Check the Cylinder Compression
Data List Display
Engine Speed of Cyl #1
Engine Speed of Cyl #2
Engine Speed of Cyl #3
Engine Speed of Cyl #4
Engine Speed of Cyl #5
Engine Speed of Cyl #6
Engine Speed of Cyl #7
Engine Speed of Cyl #8
50004 61 111 492,493,494,495,496,497,498,499

d.

Crank the engine.


e.

Check the engine speed during the Active Test.

Result:
Result Proceed to
The values of Engine Speed Cyl #1 to #8 are within 10 rpm of each other A
Other than above B


HINT:

When cranking, if the speed of a cylinder is approximately 100 rpm more than the other cylinders, there is probably a complete loss of compression in that cylinder.




A

14.REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER

B

13.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
13.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
HINT:

Measure the compression of the cylinder that had a high speed during the Active Test "Check the Cylinder Compression".



Result:
Proceed to
OK
NG



OK

14.REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

14.REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER
HINT:

It can be determined that the fuel injector is faulty as the corresponding cylinder is malfunctioning, but has no compression loss.


a.

Replace the fuel injector of the malfunctioning cylinder.

Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL INJECTOR (w/o DPF)>REMOVAL

NOTICE:
·

When replacing the fuel injector for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an fuel injector deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an fuel injector becomes out of position, it is possible that the seal between the fuel injector and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

15.BLEED AIR FROM FUEL SYSTEM
15.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

16.REGISTER INJECTOR COMPENSATION CODE
16.REGISTER INJECTOR COMPENSATION CODE
a.

Register the injector compensation codes.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION

Powertrain > Engine and ECT > Utility
Tester Display
Injector Compensation
50005 61 148

Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check whether the white smoke problem has been successfully repaired by starting the engine.


Result:
Proceed to
OK
NG



OK

END

NG

23.CHECK FUEL QUALITY
18.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP ASSEMBLY
a.

Disconnect the inlet hose from the fuel supply pump assembly.


b.

Operate the priming pump and check that fuel is being supplied to the fuel supply pump assembly.

OK:

Fuel is properly supplied to the fuel supply pump assembly when the priming pump is operated.


HINT:
·

A lack of fuel causes the fuel pressure to drop.

·

Check that the fuel filter element assembly is not clogged.




c.

Reconnect the inlet hose.


Result:
Proceed to
NEXT



NEXT

19.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
19.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
a.

Clean the fuel filter case and replace the fuel filter element assembly.

HINT:

Be sure to clean the inside of the fuel filter case as the injector assemblies may not operate properly if the fuel filter element assembly is installed with foreign matter remaining inside the fuel filter case.



Result:
Proceed to
NEXT



NEXT

20.CHECK AND REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP ASSEMBLY)
20.CHECK AND REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP ASSEMBLY)
a.

Check and replace the clogged fuel pipe.


Result:
Proceed to
NEXT



NEXT

21.BLEED AIR FROM FUEL SYSTEM
21.BLEED AIR FROM FUEL SYSTEM
HINT:

If the fuel filter element assembly or fuel pipe has been replaced, be sure to remove any air in the system.



Result:
Proceed to
NEXT



NEXT

22.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
22.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check whether the white smoke problem has been successfully repaired by starting the engine.


Result:
Proceed to
NEXT



NEXT

END

23.CHECK FUEL QUALITY
a.

Check that only diesel fuel is being used.


b.

Check that the fuel does not contain any impurities.


Result:
Proceed to
NEXT



NEXT

END

24.CHECK IDLING CONDITION
a.

Start the engine.


b.

Check the idling condition.

Result:
Result Proceed to
Engine run smoothly at idle, however white smoke is emitted. A
There are problems such as rough idling or engine stall, and white smoke is emitted.
HINT:

If the pressure in the crank case has risen, white smoke will be produced just after the engine is started. In this case, if blow-by gas is ejected when the oil level gauge is slightly removed*, it is possible that the piston is damaged.


NOTICE:

*Do not completely remove the oil level gauge as oil may spray from the opening.


B


HINT:

It is possible to determine the faulty cylinder by carrying out the "Check the Cylinder Compression" Active Test.




A

B

REPAIR ENGINE ASSEMBLY

25.CHECK FOR OIL LEAKAGE
a.

Remove any oil in the front exhaust pipe assembly.

HINT:

Oil in the exhaust pipe is producing white smoke.



b.

If there is an oil leak, repair the leak.


Result:
Proceed to
NEXT



NEXT

END