| Malfunction Condition | Main Trouble Area | Related Trouble Area |
|---|---|---|
|
·
Rough idling or juddering due to abnormal combustion
·
Juddering when vehicle is starting due to clutch system malfunctions |
(a) Fuel injector malfunctions
·
Injector sliding malfunction
·
Injector stuck closed
·
Injector stuck open
·
Deposits in injector
·
Injector circuit malfunction (b) Clutch system malfunctions
·
Clutch system (juddering when starting) |
·
Injector compensation code
·
Fuel leak
·
Engine mounting
·
Intake system leakage
·
Intake system blockage
·
Throttle valve system
·
Mass air flow meter
·
Fuel supply pump assembly (suction control valve)
·
Fuel pressure sensor
·
Low quality fuel
·
Vehicle modifications
·
Fuel filter element assembly air bleed problem
·
Accessory problem (A/C, generator, etc.)
·
ECM |
This troubleshooting procedure checks for the cause of rough idling and excessive engine vibrations.
Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List result values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors causing the malfunction.
Check that the vehicle has not been modified in any way prior to the vehicle inspection.
Faults and Symptoms of Common Rail Diesel Components
Engine Control
| Main fault | Decrease in performance (foreign matter is stuck) |
| Symptoms | Lack of power, black smoke |
| Data List | MAF |
|
|
| Main fault | Glow system malfunction |
| Symptoms | Difficult to start, rough idle, knocking, white smoke (when cold) |
| Diagnostic Point |
·
Measure the resistance of the glow plug
·
Check the glow plug indicator light |
| Main fault | Loss of compression |
| Symptoms | Rough idle (lack of power always) |
| Data List | Engine Speed of Cyl
·
When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression. Injection Feedback Val
·
When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder. |
Diesel Injection
| Main fault | - |
| Symptoms | Difficult to start, engine stalling, rough idle, lack of power |
| Data List | Fuel Press, Target Common Rail Pressure, Target Pump SCV Current
·
Fuel Press is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (the engine coolant temperature is higher than 75°C (167°F)).
·
If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt.
·
If the fuel pressure is below 25000 kPa, then idling will be rough.
|
| Diagnostic Trouble Code | Even if Fuel Press is below Target Common Rail Pressure, a DTC will not be stored. |
| Main fault | Blockage |
| Symptoms | Difficult to start, engine stalling, rough idle, lack of power |
| Data List | Fuel Press, Target Common Rail Pressure
·
Fuel Press is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (the engine coolant temperature is higher than 75°C (167°F)).
·
If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt.
·
If the fuel pressure is below 25000 kPa, then idling will be rough.
|
| Diagnostic Trouble Code | Even if Fuel Press is below Target Common Rail Pressure, a DTC will not be stored. |
| Main fault | Blockage |
| Symptoms | Rough idle, lack of power, black smoke, white smoke, knocking |
| Data List | Injection Feedback Val
·
When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder. This value can be read after idling for 1 minute. |
| Main fault | Circuit fault: The fuel fuel injector does not open. |
| Symptoms | Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking |
| Data List | Injection Feedback Val |
| Diagnostic Trouble Code | When the injector driver has a fault, some DTCs may be stored. |
| Main fault | Open circuit, decrease in performance (foreign matter is stuck) |
| Symptoms | Difficult to start, rough idle, engine stall, lack of power |
| Data List | Fuel Press, Target Common Rail Pressure
·
Slowly raise the engine speed from idling to 3000 rpm with the vehicle stopped and check that Fuel Press follows Target Common Rail Pressure. If the fuel pressure sensor malfunctions, the actual fuel pressure may deviate from the target fuel pressure (either Fuel Press decreases to a value less than Target Common Rail Pressure). |
| Diagnostic Trouble Code | When the fuel pressure sensor has a fault, some DTCs may be stored. |
| Main fault | - |
| Symptoms | Difficult to start, rough idle (especially when cold) |
Diesel Throttle
| Main fault | Stuck, does not move smoothly |
| Symptoms |
·
Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed.
·
Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur. |
| Data List | Actual Throttle Position, Actual Throttle Position #2
·
100%: Fully closed
·
0%: Fully open
·
When the ignition switch is turned to ON (the engine is stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the ignition switch is turned from ON to off, the throttle is fully closed temporarily. |
Data List Related to Rough Idling
Engine Speed
MAF
Intake Air
Coolant Temp
Engine Speed of Cyl #1 (to #8)
(Output only when the "Check the Cylinder Compression" Active Test is performed)
Target Common Rail Pressure
Fuel Press
Target Pump SCV Current
Injection Feedback Val #1 (to #8)
Injection Volume
Actual Throttle Position
Actual Throttle Position #2
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>INITIALIZATION
After replacing an fuel injector, the ECM needs registration.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION
Identify when shuddering occurs.
| Result | Proceed to |
|---|---|
| When idling | A |
| When engaging engine clutch at vehicle start | B (Clutch system shudders) |
A
B
Check the wire harness and connector connections of common rail system components.
The wire harnesses and connectors are connected securely.
The engine may have problems when there is an intermittent disconnection in a circuit related to the fuel pressure sensor, crankshaft position sensor, engine coolant temperature sensor, etc.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the pending DTCs.
| Result | Proceed to |
|---|---|
| No DTCs are output | A |
| Engine related DTCs are output | B |
If only DTC P1605 is output, proceed to step 4.
A
B
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).
Enter the following menus: Powertrain / Engine and ECT / Data List / Diesel Rough Idle.
Take a snapshot when idling with no load after the engine is warmed up and when the problem is occurring.
A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.
The shift lever should be in neutral and the A/C switch and all accessory switches should be off.
If rough idling occurs when the A/C switch is on, take another snapshot with the A/C switch on.
Take a snapshot when the problem is occurring, such as when the engine is cold. However, if the problem does not reoccur, it is acceptable to only take a snapshot after the engine is warmed up.
| Proceed to |
|---|
| NEXT |
NEXT
Start the engine.
Fully depress the accelerator pedal, and then release it.
Check whether white smoke is emitted when racing the engine.
Be sure not to check for white smoke indoors.
Depending on whether there is oil mixed with the fuel, or whether there is unburned fuel present, the smell of the exhaust gas differs. When oil is mixed in, the exhaust gas smells such as burning oil.
| Result | Proceed to |
|---|---|
| White smoke is not emitted | A |
| White smoke is emitted | B |
A
B
Check the engine speed in the snapshot taken in procedure 4 when the engine was idling.
| Result | Proceed to |
|---|---|
| Change in engine speed coincides with air conditioning system operation | B |
| Except above | A |
A
B
Check Injection Feedback Val # in the snapshot taken in procedure 4 when the engine was idling.
| Result | Result |
|---|---|
| Injection Feedback Val for at least one cylinder is more than +3 mm3/st and engine vibration is abnormally large | A |
| Except above | B |
When there is a problem with the operation of an fuel injector due to foreign matter in the inside of the fuel injector, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.
The ECM controls the system so that the sum of Injection Feedback Val for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Val for a cylinder is less than -3.0 mm3/st, as long as the value of Injection Feedback Val for each of the other cylinders is 3.0 mm3/st or less, the fuel injectors are not malfunctioning.
A
B
Read the injector compensation code.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION
Compensation codes stored in the ECM match compensation codes of the installed injector assemblies.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Use this Active Test to determine the malfunctioning cylinder.
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Select Cylinder Fuel Cut.
If the engine idle speed does not change when an fuel injector is disabled, the cylinder being tested is malfunctioning.
If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.
| Tester Display |
|---|
| Control the Select Cylinder Fuel Cut |
| Proceed to |
|---|
| NEXT |
NEXT
Replace the fuel injector of the malfunctioning cylinder.
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL INJECTOR (w/o DPF)>REMOVAL
When replacing the fuel injector for a cylinder, always be sure to use a new injection pipe.
Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
If an fuel injector deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
If an fuel injector becomes out of position, it is possible that the seal between the fuel injector and injection pipe may become incomplete, resulting in a fuel leak.
| Proceed to |
|---|
| NEXT |
NEXT
Clean the fuel filter case and replace the fuel filter element assembly.
Be sure to clean the inside of the fuel filter case as the injector assemblies may not operate properly if the fuel filter element assembly is installed with foreign matter remaining inside the fuel filter case.
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL SYSTEM(w/o DPF)>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Register the injector compensation code.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION
| Tester Display |
|---|
| Injector Compensation |
| Proceed to |
|---|
| NEXT |
NEXT
Check the engine speed in the snapshot taken in procedure 4 when the engine was idling after having been warmed up.
| Result | Proceed to |
|---|---|
| Difference between Fuel Press and Target Common Rail Pressure is 5000 kPa (51.0 kgf/cm2, 725 psi) or more | A |
| Except above | B |
A
B
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Target Common Rail Pressure and Fuel Press.
| Tester Display |
|---|
| Target Common Rail Pressure |
| Fuel Press |
With no load after the engine is warmed up, take a snapshot when idling and vehicle was accelerating with the accelerator pedal fully depressed in 2nd gear.
Check the Target Common Rail Pressure and Fuel Press.
| Result | Proceed to |
|---|---|
| While idling the vehicle, "Fuel Press" deviates from the normal range and varies periodically with a period of approximately 2 seconds or more*1 | A |
| "Fuel Press" is normal while idling the vehicle, but "Fuel Press" does not follow "Target Common Rail Pressure" when the accelerator pedal is fully depressed in 2nd gear*2 | |
| Except above | B |
*1: The cause may be a squashed or blocked fuel pipe or hose.
*2: The cause may be a clogged fuel filter.
A
B
Repair or replace the clogged (including frozen fuel) fuel pipe.
Replace the fuel filter element assembly.
If "Fuel Press" does not follow "Target Common Rail Pressure" when the accelerator pedal is fully depressed in 2nd gear, replace the fuel filter element assembly.
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL SYSTEM(w/o DPF)>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Check the air conditioning system.
Be sure to check the air conditioning hoses and pipes.
Check the refrigerant pressure.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Replace the fuel supply pump assembly.
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL SUPPLY PUMP (w/o DPF)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Perform fuel supply pump initialization.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL SYSTEM(w/o DPF)>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Check the following items and repair the malfunctioning part if necessary.
Check the cylinder compression pressure.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Check rough idling or excessive engine vibrations.
| Result | Proceed to |
|---|---|
| Rough idling or excessive engine vibrations do not occur | A |
| Except above | B |
A
B
Check the following items and repair or replace the malfunctioning part if necessary.
Check that the engine mounting insulators are installed correctly.
Check that the engine mounting insulators are not twisted.
Check that deformation of an engine mounting insulator is not causing the engine to contact the vehicle body.
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT