Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o EGR System) › 2017.01–2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0309414 ECD SYSTEM(w/o EGR System) J

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR System)  VC Output Circuit  


DESCRIPTION

The ECM constantly generates 5 V of power from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A187745E10
1.271,1.094 2.729,1.292 1.458,0.198 10 false from EFI MAIN Fuse 1.458,1.448 2.875,1.646 1.417,0.198 10 false from MAIN Relay 2.854,1.031 3.229,1.229 0.375,0.198 10 false BATT 2.813,1.354 3.406,1.521 0.594,0.167 10 false +B 0.302,1.99 2.625,3 2.323,1.01 10 false Throttle Position Sensor, Accelerator Pedal Position Sensor, etc. (Sensors which have ICs) 0.323,2.979 2.563,3.656 2.24,0.677 10 false Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 2.698,1.896 3.604,2.469 0.906,0.573 10 false VCEG, VCPA, VCP2, VCVL, VCM, VCPM 4.063,3.125 4.25,3.323 0.188,0.198 10 false R 4.792,3.344 5.146,3.542 0.354,0.198 10 false ECM 4.438,1.115 6.167,1.313 1.729,0.198 10 false 5V Constant Voltage Circuit 5.385,2 6.375,2.198 0.99,0.198 10 false Microprocessor

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

·

VC power source circuit


A402456E01
5.01,0.385 5.625,0.583 0.615,0.198 10 false VCVL 5,1.198 5.615,1.396 0.615,0.198 10 false EVLU 5,0.781 5.615,0.979 0.615,0.198 10 false VLU 5,2.646 5.615,2.844 0.615,0.198 10 false VLU2 4.656,0.385 5.01,0.563 0.354,0.177 10 false C39 4.656,0.781 5.01,0.958 0.354,0.177 10 false C39 4.656,1.177 5.01,1.354 0.354,0.177 10 false C39 4.698,0.198 5.052,0.375 0.354,0.177 10 false 91 4.708,0.594 5.063,0.771 0.354,0.177 10 false 93 4.708,0.99 5.063,1.167 0.354,0.177 10 false 92 4.677,2.469 5.031,2.646 0.354,0.177 10 false 103 4.667,2.646 5.021,2.823 0.354,0.177 10 false C39 2.229,0.385 2.844,0.583 0.615,0.198 10 false VC 2.271,1.188 2.885,1.385 0.615,0.198 10 false E2 2.167,0.792 2.781,0.99 0.615,0.198 10 false VTA 2.24,2.24 2.854,2.438 0.615,0.198 10 false VC 2.26,3.052 2.875,3.25 0.615,0.198 10 false E2 2.177,2.635 2.792,2.833 0.615,0.198 10 false VTA 2.531,2.125 2.708,2.313 0.177,0.188 10 false 1 2.531,2.948 2.708,3.135 0.177,0.188 10 false 2 2.531,2.531 2.708,2.719 0.177,0.188 10 false 3 2.552,0.25 2.729,0.438 0.177,0.188 10 false 1 2.552,0.656 2.729,0.844 0.177,0.188 10 false 3 2.552,1.052 2.729,1.24 0.177,0.188 10 false 2 0.823,1.625 3.083,1.833 2.26,0.208 10 false Throttle Position Sensor (for Bank 1) 0.823,1.448 1.438,1.646 0.615,0.198 10 false C50 0.844,3.354 1.458,3.552 0.615,0.198 10 false C65 0.844,3.51 3.104,3.719 2.26,0.208 10 false Throttle Position Sensor (for Bank 1) 0.875,6.083 3.135,6.292 2.26,0.208 10 false Accelerator Pedal Position Sensor 0.854,5.917 1.469,6.115 0.615,0.198 10 false I43 5,4 5.615,4.198 0.615,0.198 10 false VPA 4.99,4.354 5.604,4.552 0.615,0.198 10 false EPA 4.99,4.708 5.604,4.906 0.615,0.198 10 false VCPA 4.979,5.042 5.594,5.24 0.615,0.198 10 false VPA2 4.99,5.385 5.604,5.583 0.615,0.198 10 false EPA2 4.99,5.75 5.604,5.948 0.615,0.198 10 false VCP2 4.708,4 5.063,4.177 0.354,0.177 10 false I84 4.708,4.354 5.063,4.531 0.354,0.177 10 false I84 4.708,4.698 5.063,4.875 0.354,0.177 10 false I84 4.698,5.052 5.052,5.229 0.354,0.177 10 false I84 4.698,5.396 5.052,5.573 0.354,0.177 10 false I84 4.698,5.74 5.052,5.917 0.354,0.177 10 false I84 2.531,5.625 2.708,5.813 0.177,0.188 10 false 1 2.531,5.281 2.708,5.469 0.177,0.188 10 false 2 2.531,4.948 2.708,5.135 0.177,0.188 10 false 3 2.531,4.583 2.708,4.771 0.177,0.188 10 false 4 2.531,4.25 2.708,4.438 0.177,0.188 10 false 5 2.531,3.896 2.708,4.083 0.177,0.188 10 false 6 4.698,3.823 5.052,4 0.354,0.177 10 false 53 4.708,4.177 5.063,4.354 0.354,0.177 10 false 57 4.708,4.521 5.063,4.698 0.354,0.177 10 false 55 4.708,4.875 5.063,5.052 0.354,0.177 10 false 54 4.698,5.219 5.052,5.396 0.354,0.177 10 false 58 4.708,5.573 5.063,5.75 0.354,0.177 10 false 56 2.135,4.01 2.75,4.208 0.615,0.198 10 false VPA 2.146,4.354 2.76,4.552 0.615,0.198 10 false EPA 2.052,4.698 2.667,4.896 0.615,0.198 10 false VCPA 2.073,5.052 2.688,5.25 0.615,0.198 10 false VPA2 2.073,5.406 2.688,5.604 0.615,0.198 10 false EPA2 2.094,5.75 2.708,5.948 0.615,0.198 10 false VCP2 0.875,7.76 3.135,7.969 2.26,0.208 10 false Accelerator Pedal Position Sensor 0.885,7.594 1.5,7.792 0.615,0.198 10 false C100 0.844,9.49 3.104,9.698 2.26,0.208 10 false Manifold Absolute Pressure Sensor 0.823,9.302 1.438,9.5 0.615,0.198 10 false C101 4.667,6.594 5.021,6.771 0.354,0.177 10 false C39 4.667,6.99 5.021,7.167 0.354,0.177 10 false C39 4.677,7.396 5.031,7.573 0.354,0.177 10 false C39 5,7 5.615,7.198 0.615,0.198 10 false VCM 5.01,6.615 5.625,6.813 0.615,0.198 10 false PCR1 5,7.406 5.615,7.604 0.615,0.198 10 false E2 4.708,6.396 5.063,6.573 0.354,0.177 10 false 69 4.698,6.813 5.052,6.99 0.354,0.177 10 false 70 4.698,7.208 5.052,7.385 0.354,0.177 10 false 75 2.531,7.26 2.708,7.448 0.177,0.188 10 false 1 2.531,6.469 2.708,6.656 0.177,0.188 10 false 2 2.51,6.885 2.688,7.073 0.177,0.188 10 false 3 2.25,7.385 2.865,7.583 0.615,0.198 10 false E2 2.25,7 2.865,7.198 0.615,0.198 10 false VC 2.25,6.604 2.865,6.802 0.615,0.198 10 false PR 5.01,8.302 5.625,8.5 0.615,0.198 10 false VCPM 4.99,8.729 5.604,8.927 0.615,0.198 10 false PIM 2.344,9.115 2.958,9.313 0.615,0.198 10 false E 4.677,8.313 5.031,8.49 0.354,0.177 10 false C39 4.656,8.708 5.01,8.885 0.354,0.177 10 false C39 2.542,9.01 2.719,9.198 0.177,0.188 10 false 1 2.177,8.719 2.792,8.917 0.615,0.198 10 false PIM 2.26,8.323 2.875,8.521 0.615,0.198 10 false VC 2.542,8.177 2.719,8.365 0.177,0.188 10 false 3 2.542,8.615 2.719,8.802 0.177,0.188 10 false 2 4.667,8.521 5.021,8.698 0.354,0.177 10 false 114 4.698,8.135 5.052,8.313 0.354,0.177 10 false 66 5.49,9.49 6.104,9.688 0.615,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Check the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK CONNECTION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

2.CHECK ECM POWER SOURCE CIRCUIT

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK ECM POWER SOURCE CIRCUIT

Result:
Proceed to
NEXT



NEXT

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR [for Bank 1])
3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR [for Bank 1])
a.

Disconnect the throttle position sensor (for Bank 1) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.


Result:
Result Proceed to
Communication is possible A
Communication is not possible B




B

4.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR [for Bank 2])

A

REPLACE DIESEL THROTTLE BODY ASSEMBLY (for Bank 1)

4.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR [for Bank 2])
a.

Disconnect the throttle position sensor (for Bank 2) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is possible A
Communication is not possible B



B

5.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)

A

REPLACE DIESEL THROTTLE BODY ASSEMBLY (for Bank 2)

5.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal position sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is possible A
Communication is not possible B



B

6.CHECK CONNECTION BETWEEN GTS AND ECM (MANIFOLD ABSOLUTE PRESSURE SENSOR)

A

REPLACE ACCELERATOR PEDAL ROD ASSEMBLY

6.CHECK CONNECTION BETWEEN GTS AND ECM (MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is possible A
Communication is not possible B



B

7.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR)

A

7.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR)
a.

Disconnect the fuel pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is possible A
Communication is not possible B



B

8.CHECK HARNESS AND CONNECTOR

A

8.CHECK HARNESS AND CONNECTOR
a.
A311475C05
1.25,0.188 1.667,0.479 0.417,0.292 0.281,3.25 0.698,3.542 0.417,0.292 0.323,2.115 0.479,1.427 true 2.083,3.635 2.333,4.104 false 1.375,4.104 1.969,3.625 false 1.354,1.438 1.99,2.104 true 0.646,1.26 1.198,2.125 true 1.167,1.031 2.792,2.104 true 0.125,0.188 0.438,0.385 0.313,0.198 10 false *a 0.198,2.417 0.51,2.615 0.313,0.198 10 false *b 1.344,0.25 1.802,0.448 0.458,0.198 10 false C39 0.354,3.313 0.813,3.51 0.458,0.198 10 false A29 2.271,4.146 3.104,4.542 0.833,0.396 10 false 56 (VCP2) 1.219,4.146 2.052,4.542 0.833,0.396 10 false 55 (VCPA) 1.719,2.156 2.552,2.552 0.833,0.396 10 false 120 (VCEG) 0.906,2.156 1.74,2.552 0.833,0.396 10 false 66 (VCPM) 0.063,2.156 0.896,2.552 0.833,0.396 10 false 110 (VCVL) 2.583,2.156 3.417,2.552 0.833,0.396 10 false 118 (VCM)
*a Front view of wire harness connector
(to ECM)
*b Front view of wire harness connector
(to ECM)


Disconnect the throttle position sensor (for Bank 1) connector.


b.

Disconnect the throttle position sensor (for Bank 2) connector.


c.

Disconnect the accelerator pedal position sensor connector.


d.

Disconnect the manifold absolute pressure sensor connector.


e.

Disconnect the fuel pressure sensor connector.


f.

Disconnect the ECM connectors.


g.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
I84-55 (VCPA) - Body ground Always 10 kΩ or higher
I84-56 (VCP2) - Body ground Always 10 kΩ or higher
C39-91 (VCVL) - Body ground Always 10 kΩ or higher
C39-70 (VCM) - Body ground Always 10 kΩ or higher
C39-66 (VCPM) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR