Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0548732 VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System)  C00632A  Yaw Rate Sensor Signal Stuck In Range  C05201C  Multi-axis Acceleration Sensor Module "A" Circuit Voltage Out of Range  C05202A  Multi-axis Acceleration Sensor Module "A" Signal Stuck In Range  C052096  Multi-axis Acceleration Sensor Module "A" Component Internal Failure  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate sensor and acceleration sensor (airbag ECU assembly) via CAN communication.

HINT:

If there is a malfunction in the bus lines between the yaw rate sensor and acceleration sensor (airbag ECU assembly) and the CAN communication system, DTCs U012587 are output. When DTCs U012587 are output together with C00632A, C05201C, C05202A and/or C052096, inspect and repair the trouble areas indicated by U012587 first.


DTCs may be stored if either of the following occurs:

·

Acceleration sensor (airbag ECU assembly) installation abnormality.

·

Acceleration sensor (airbag ECU assembly) signal malfunction.


DTC No. Detection Item DTC Detection Condition Trouble Area
C00632A Yaw Rate Sensor Signal Stuck In Range A yaw rate sensor stuck malfunction status continues.
·

Sensor installation

·

Yaw rate sensor (Airbag ECU assembly)


C05201C Multi-axis Acceleration Sensor Module "A" Circuit Voltage Out of Range At a vehicle speed of 30 km/h (19 mph) or more, the difference between the forward and backward G calculated from the acceleration sensor value and that calculated from the vehicle speed sensor exceeds 0.35 G for 60 seconds or more.
·

Sensor installation

·

Acceleration sensor (Airbag ECU assembly)


C05202A Multi-axis Acceleration Sensor Module "A" Signal Stuck In Range Any of the following is detected:
·

The acceleration sensor output value does not change 16 times or more as the vehicle speed drops from 30 km/h (19 mph) to 0 km/h (0 mph).

·

Front/rear sensor stuck malfunction status continues.

·

Left/right sensor stuck malfunction status continues.


·

Sensor installation

·

Acceleration sensor (Airbag ECU assembly)


C052096 Multi-axis Acceleration Sensor Module "A" Component Internal Failure Any of the following is detected:
·

A data malfunction signal is received from the acceleration sensor.

·

Output values of GL1 and GL2 (front and rear, left and right) are outside permitted output range for 60 seconds or more.

·

Left and right output values of the acceleration sensor are outside permitted output range for 60 seconds or more.


·

Sensor installation

·

Acceleration sensor (Airbag ECU assembly)



C05202A DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition - - - -
Malfunction Status The acceleration sensor output value does not change 16 times or more as the vehicle speed drops from 30 km/h (19 mph) to 0 km/h (0 mph) ○ - -
Front/rear sensor stuck malfunction status continues - ○ -
Left/right sensor stuck malfunction status continues - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


C052096 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition - - - -
Malfunction Status A data malfunction signal is received from the acceleration sensor ○ - -
Output values of GL1 and GL2 (front and rear, left and right) are outside permitted output range - ○ -
Left and right output values of the acceleration sensor are outside permitted output range - - ○
Detection Time - 60 seconds or more. 60 seconds or more.
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:

If the yaw rate and acceleration sensor (airbag ECU assembly) was replaced or reinstalled, perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>CALIBRATION


HINT:

When U012587 is output together with C00632A, C05201C, C05202A, and/or C052096, inspect and repair the trouble areas indicated by U012587 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>U007488


PROCEDURE

1.CHECK AIRBAG ECU ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the airbag ECU assembly has been installed properly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION

OK:

The sensor should be tightened to the specified torque.

The sensor should not be tilted position.



Result:
Proceed to
OK
NG



OK

NG

INSTALL AIRBAG ECU ASSEMBLY CORRECTLY