Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0548732 VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System)  C05262A  Steering Angle Sensor Module Signal Stuck In Range  


DESCRIPTION

Steering sensor signals are input to the skid control ECU (brake actuator assembly) via the CAN communication system.

HINT:

When a malfunction occurs in the communication line to the steering sensor, U012687 is output.

If a DTC related to the CAN communication line is output, first troubleshoot the CAN communication line.


DTC No. Detection Item DTC Detection Condition Trouble Area
C05262A Steering Angle Sensor Module Signal Stuck In Range Normal communication between the skid control ECU and the steering sensor and abnormal steering sensor zero point.
·

Wire harness or connector

·

Steering sensor (Spiral cable with sensor sub-assembly)

·

Skid control ECU (Brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the steering sensor, confirm that the replacement part is of the correct specification.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When U007488, U012587 and/or U012687 is output together with C05262A, inspect and repair the trouble areas indicated by U007488, U012587 and/or U012687 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>U007488

·

When any of the speed sensors or the yaw rate and acceleration sensor (airbag ECU assembly) has trouble, DTCs for the steering sensor may be output even when the steering sensor is normal. When DTCs for the speed sensors or yaw rate and acceleration sensor (airbag ECU assembly) are output together with DTCs for the steering sensor, inspect and repair the speed sensor and yaw rate and acceleration sensor (airbag ECU assembly) first, and then inspect and repair the steering sensor.



PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON again and check that no CAN communication system DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Pre-collision System)>DIAGNOSIS SYSTEM


d.

Start the engine.


e.

Drive the vehicle at a speed of 35 km/h (22 mph) and turn the steering wheel to the right and left to check that no speed sensor or yaw rate and acceleration sensor DTCs are output.

Chassis > Brake > Trouble Codes
50001 435
HINT:
·

If there is a malfunction in any of the speed sensors or the yaw rate and acceleration sensor (airbag ECU assembly), an abnormal value may be output although the steering sensor is normal.

·

If speed sensor and yaw rate and acceleration sensor (airbag ECU assembly) DTCs are output simultaneously, repair these two sensors first and inspect the steering sensor.




Result:
Result Proceed to
No CAN communication system, speed sensor, or yaw rate and acceleration sensor DTCs are output A
CAN communication system DTC is output B
Speed sensor or yaw rate and acceleration sensor DTC is output C



A

2.CHECK TERMINAL VOLTAGE (BAT TERMINAL)

B

C

REPAIR CIRCUIT INDICATED BY OUTPUT DTC

2.CHECK TERMINAL VOLTAGE (BAT TERMINAL)
a.

Turn the ignition switch off.


b.
C364760C04
0.24,1.167 0.615,1.417 0.375,0.25 2.354,1.885 2.354,1.5 false 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 0.323,1.208 0.708,1.427 0.385,0.219 10 false L47 2.24,1.917 2.594,2.125 0.354,0.208 10 false BAT
*a Front view of wire harness connector
(to Steering Sensor [Spiral Cable with Sensor Sub-assembly])


Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the L47 steering sensor (spiral cable with sensor sub-assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L47-6 (BAT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (IG TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BAT CIRCUIT)

3.CHECK TERMINAL VOLTAGE (IG TERMINAL)
a.

Turn the ignition switch to ON.


b.
C364760C05
0.24,1.167 0.615,1.417 0.375,0.25 2.063,1.885 2.063,1.5 false 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 0.323,1.208 0.708,1.427 0.385,0.219 10 false L47 2,1.917 2.354,2.125 0.354,0.208 10 false IG
*a Front view of wire harness connector
(to Steering Sensor [Spiral Cable with Sensor Sub-assembly])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L47-5 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)
a.

Turn the ignition switch off.


b.
C364760C06
0.24,1.167 0.615,1.417 0.375,0.25 1.354,1.885 1.354,1.5 false 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 0.323,1.208 0.708,1.427 0.385,0.219 10 false L47 1.208,1.917 1.563,2.125 0.354,0.208 10 false ESS
*a Front view of wire harness connector
(to Steering Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L47-2 (ESS) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ESS CIRCUIT)