Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0548732 VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System)  C054017  Brake Pressure Sensor "A" Circuit Voltage Above Threshold  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
C054017 Brake Pressure Sensor "A" Circuit Voltage Above Threshold When vehicle speed is 3 km/h (2 mph) or more and stop light switch assembly is OFF, master cylinder pressure continuously exceeds 1.764 MPa (18.0 kgf/cm2, 255 psi) for 5 seconds or more.
·

Stop light switch assembly

·

Wire harness or connector

·

Skid control ECU (Brake actuator assembly)

·

Master cylinder pressure sensor (Brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Perform a road test.


e.

Check for DTCs.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
DTC C054017 is output A
DTCs C054017 and P057113 are output B



A

2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)
a.

In accordance with the display on the GTS, read the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly ON or OFF OFF: Brake pedal released
ON: Brake pedal depressed
-
Chassis > Brake > Data List
Tester Display
Stop Light SW
50003 435 59

b.

Check that the stop light switch assembly condition observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (MASTER CYLINDER PRESSURE SENSOR)

NG

5.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
3.READ VALUE USING GTS (MASTER CYLINDER PRESSURE SENSOR)
a.

In accordance with the display on the GTS, read the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Master Cylinder Sensor 1 Master cylinder pressure sensor pressure (value detected by ECU) Min.: -1.00 MPa
Max.: 23.99 MPa
Brake pedal released: -1.00 to 0.00 MPa Reading increases when brake pedal is depressed
Chassis > Brake > Data List
Tester Display
Master Cylinder Sensor 1
50003 435 21
OK:

The value of Data List item Master Cylinder Sensor is within standard range.



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

4.RECONFIRM DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Perform a road test.


e.

Check if the same DTC is recorded.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
DTC C054017 is not output A
DTC C054017 is output B



A

B

5.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check the brake pedal height and stop light switch assembly installation.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL>ADJUSTMENT

OK:

The brake pedal height and stop light switch assembly installation are normal.



Result:
Proceed to
OK
NG



OK

6.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY

6.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION

OK:

The stop light switch assembly is normal.


Result:
Proceed to
OK
NG




OK

7.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL)
a.
C494113C04
1.542,0.094 2,0.333 0.458,0.24 1.594,1.281 1.594,1.833 true 1.469,1.875 1.927,2.104 0.458,0.229 10 false STP2 1.635,0.135 1.938,0.344 0.302,0.208 10 false A45 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A45 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A45-37 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 8 to 14 V
Stop light switch assembly off (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP2 CIRCUIT)