The ABS solenoid relay supplies power to the ABS solenoid and TRC solenoid.
The solenoid relay is turned on 1.5 seconds after the ignition switch is turned to ON, and is turned off if an open or short in the solenoid is detected by the self diagnosis performed when the engine starts running.
The ABS solenoid relay is housed in the skid control ECU in the actuator assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C143A7E | ABS Solenoid Control Module Actuator Stuck On | When voltage at terminal +BS is 9.5 V or higher, solenoid relay is OFF, relay contact is ON continuously for 4.5 seconds or more. | Skid control ECU (Brake actuator assembly) |
| C143A7F | ABS Solenoid Control Module Actuator Stuck Off | When voltage at terminal +BS is 9.5 V or higher and solenoid relay is ON, relay contact is OFF continuously for 0.22 seconds or more. |
·
Wire harness or connector
·
Skid control ECU (Brake actuator assembly) |
After replacing the skid control ECU (brake actuator assembly), perform "Calibration".
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
When C137BA2 and/or C137BA3 is output together with C143A7E and/or C143A7F, inspect and repair the trouble areas indicated by C137BA2 and/or C137BA3 first.
for C137BA2: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>C137BA2
for C137BA3: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>C137BA3
| *a | Front view of wire harness connector (to Skid Control ECU [Brake Actuator Assembly]) |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the A45 skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A45-14 (+BS) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector (to Skid Control ECU [Brake Actuator Assembly]) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A45-1 (GND1) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
These codes are detected when a problem is determined in the skid control ECU (brake actuator assembly).
The solenoid circuits are in the skid control ECU (brake actuator assembly).
Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed.
Be sure to check if any DTCs are output before replacing the skid control ECU (brake actuator assembly).
Reconnect the A45 skid control ECU (brake actuator assembly) connector.
Clear the DTCs.
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.
Check if the same DTC is recorded.
| Result | Proceed to |
|---|---|
| DTC C143A7E and/or C143A7F are not output | A |
| DTC C143A7E and C143A7F are output | B |
If a speed signal of 20 km/h (12 mph) or more is input to the skid control ECU (brake actuator assembly), with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.
If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.
If any DTCs are output while jiggling a connector or wire harness from the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.
The DTCs were probably output due to a bad connection of the connector terminal.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B