Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE HUB › from 2022.09
RM25T0E _52 Drivetrain _029907 AXLE AND DIFFERENTIAL _0138021 REAR AXLE HUB A

AXLE AND DIFFERENTIAL  REAR AXLE HUB  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 42311A 1.INSTALL REAR AXLE SHAFT OIL SEAL (for Drum Type)

a.

Install a new rear axle shaft oil seal with the 4 bolts and 4 nuts.

Torque:
123 N*m (1254 kgf*cm, 91 ft.*lbf)


Hide 2.INSTALL REAR BRAKE SHOE (for Drum Type)

Hide 3.INSTALL BEARING OUTER RACE

a.
C314317C01
0.531,2.281 0.938,2.281 0.938,2.281 1.438,2.583 true 1.76,1.146 2.646,1.146 true 1.917,1.365 2.333,1.365 2.333,1.365 2.333,1.146 true 0.344,2.229 0.656,2.385 0.313,0.156 10 false *1 2.729,1.083 3.156,1.344 0.427,0.26 10 false SST
*1 Outside Bearing Outer Race


Using SST and hammer, install a new outside bearing outer race.

SST
09950-60020  09950-70010  (09951-00720, 09951-07150)


b.
C271680C01
1.75,1.104 2.865,1.104 true 1.906,1.208 2.573,1.208 2.573,1.208 2.573,1.104 true 0.438,2.365 1.271,2.365 true 0.271,2.292 0.583,2.448 0.313,0.156 10 false *1 2.938,1.031 3.354,1.25 0.417,0.219 10 false SST
*1 Inside Bearing Outer Race


Using SST and hammer, install a new inside bearing outer race.

SST
09950-60020  09950-70010  (09951-00810, 09951-07150)


Hide 4.PACK BEARING WITH MP GREASE

a.

Place MP grease in the palm of your hand.


b.

Pack grease into the bearing, continuing until the grease oozes out from the other side.


c.

Do the same around the bearing circumference.


Hide 5.COAT INSIDE OF AXLE HUB WITH MP GREASE

a.
C311694C01
1.51,1.365 0.406,1.177 0.406,1.177 1.448,0.781 false 0.229,1.094 0.542,1.25 0.313,0.156 10 false *a
*a MP grease


Coat the inside of the axle hub with MP grease.


Hide 42312G 6.INSTALL REAR AXLE SHAFT INNER BEARING LH

a.

Install the rear axle shaft inner bearing LH to the rear axle hub.


Hide 42402E 7.INSTALL REAR AXLE HUB OIL SEAL LH

a.
C378271C01
1.75,1 2.667,1 true 1.917,1.167 2.417,1.167 2.417,1.167 2.417,1 false 1.75,2 2.667,2 false 2.083,2.25 2.417,2.25 2.417,2.25 2.417,2 false 0.667,2.5 1.333,2.5 true 2.75,0.917 3.208,1.115 0.458,0.198 10 false SST 2.75,1.917 3.208,2.115 0.458,0.198 10 false SST 0.448,2.427 0.76,2.625 0.313,0.198 10 false *1
*1 Rear Axle Hub Oil Seal LH


Using SST, install a new rear axle hub oil seal LH to the rear axle hub.

SST
09223-15020  09950-70010  (09951-07150)


b.

Coat the seal lip with MP grease.


Hide 42440 8.INSTALL REAR AXLE HUB AND INNER BEARING ASSEMBLY LH

a.

Install the rear axle hub and inner bearing assembly LH to the rear axle housing.

NOTICE:

Be careful not to damage the oil seal.



Hide 42312F 9.INSTALL REAR AXLE SHAFT OUTER BEARING LH

a.

Install the rear axle shaft outer bearing LH to the rear axle hub.


Hide 42427 10.TEMPORARILY INSTALL REAR AXLE BEARING LOCK NUT

a.
C271684C01
2.021,0.167 2.313,0.167 2.313,0.167 2.49,0.542 true 2.76,1.51 2.76,0.635 true 1.844,0.083 2.156,0.24 0.313,0.156 10 false *1 2.688,1.552 3,1.708 0.313,0.156 10 false *2
*1 Rear Axle Lock Nut Plate LH
*2 Rear Axle Bearing Lock Nut


After fully pushing in the outer bearing, insert the protrusion of the lock nut plate into the rear axle housing groove.


b.

Temporarily install the rear axle bearing lock nut.


Hide 42312E 11.INSTALL REAR AXLE HUB BOLT LH

Hide 42431 12.INSTALL REAR DISC (for Disc Type)

Hide 42403 13.INSTALL REAR BRAKE DRUM SUB-ASSEMBLY (for Drum Type)

Hide 14.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY LH (for Disc Type)

a.

Install the rear disc brake cylinder assembly with the 2 bolts.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


Hide 15.INSTALL REAR SPEED SENSOR LH (w/ ABS)

a.

Connect the rear speed sensor with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Prevent foreign matter from adhering to the speed sensor.

·

Be careful not to damage the speed sensor.

·

Do not twist the sensor wire when installing the speed sensor.




Hide 16.ADJUST PRELOAD

a.
C271687N01
0.802,1.938 1.229,1.938 1.229,1.938 1.615,1.542 true 0.49,1.854 0.865,2.063 0.375,0.208 10 false SST

Using SST, tighten the rear axle bearing lock nut.

SST
09509-25011  

Torque:
59 N*m (602 kgf*cm, 44 ft.*lbf)


b.
C271685

Settle the bearing by turning the hub several times.


c.
C271687N01
0.802,1.938 1.229,1.938 1.229,1.938 1.615,1.542 true 0.49,1.854 0.865,2.063 0.375,0.208 10 false SST

Using SST, retighten the rear axle bearing lock nut.

SST
09509-25011  

Torque:
59 N*m (602 kgf*cm, 44 ft.*lbf)


d.

Using SST, loosen the rear axle bearing lock nut until it can be turned by hand.

SST
09509-25011  


e.
C271631

Using a spring tension gauge, measure the preload.

Rear wheel bearing preload (at starting):

1.8 to 4.0 N (0.2 to 0.4 kgf, 0.4 to 0.9 lbf)


HINT:

If the preload is not within the specified range, the procedure above must be repeated.



f.
C271688C01
0.313,0.271 0.594,0.271 0.594,0.271 1.125,0.708 true 0.49,1.833 0.896,1.833 0.896,1.833 1.885,1.344 true 0.927,1.813 1.24,1.01 true 0.125,0.177 0.438,0.333 0.313,0.156 10 false *a 0.302,1.75 0.615,1.906 0.313,0.156 10 false *b
*a Rear Axle Bearing Lock Nut Mark
*b Mark on Rear Axle Housing End


Align the rear axle bearing lock nut mark with one of the marks on the axle housing end, and place lock screws in the holes at right angles to the rear axle bearing lock nut.


g.
C271689C01
0.552,1.01 0.979,1.01 0.979,1.01 1.313,0.615 true 1.948,0.583 2.552,0.583 false 2.156,1.177 1.781,1.177 1.781,1.177 1.427,0.781 false 0.396,0.938 0.708,1.094 0.313,0.156 10 false *1 2.208,1.104 2.521,1.26 0.313,0.156 10 false *2 2.604,0.51 2.917,0.667 0.313,0.156 10 false *3
*1 Rear Axle Lock Nut Plate LH
*2 Rear Axle Housing
*3 Rear Axle Bearing Lock Nut


Measure the distance between the top surface of axle housing and the rear axle bearing lock nut.

Standard distance:

-0.2 to 0.9 mm (-0.008 to 0.035 in.)


HINT:

If the distance is not as specified, reinstall the rear axle hub.



h.

Check the movement of the disc rotor.


i.
C271676

Check the axle hub axial play.

Hub axial play:

Less than 0.1 mm (0.004 in.)



j.
C314312

Install the 2 lock nut set screws.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 42312C 17.INSTALL REAR AXLE SHAFT OIL SEAL LH

Hide 42312 18.INSTALL REAR AXLE SHAFT LH

Hide 19.ADJUST PARKING BRAKE (for Disc Type)

Hide 20.ADJUST REAR DRUM BRAKE (for Drum Type)

Hide 21.INSTALL REAR WHEEL