| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| B1507 | Open in Turn Signal Circuit | Open in turn signal light circuit. |
·
Harness or connector
·
Front turn signal light socket
·
Side turn signal light socket and wire
·
Rear combination light socket and wire sub-assembly
·
Combination meter assembly |
○ |
| B1508 | Short in Turn Signal / Hazard Flasher Circuit | Short in turn signal light circuit or hazard warning light circuit. |
·
Harness or connector
·
Front turn signal light socket
·
Side turn signal light socket and wire
·
Rear combination light socket and wire sub-assembly
·
Combination meter assembly |
○ |
Inspect the bulbs for circuits related to this system before performing the following procedure.
Clear the DTCs.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| B1507 and B1508 are not output | A |
| B1507 is output | B |
| B1508 is output | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Check the illumination of each turn signal light.
| Result | Proceed to |
|---|---|
| LH side turn signal light does not illuminate. | A |
| RH side turn signal light does not illuminate. | B |
A
B
*1: except Pickup
*2: for Pickup
*3: for Small Type
*4: for Large Type
Disconnect the L50 combination meter assembly connector.
Disconnect the A3 front turn signal light socket LH connector.
Disconnect the A11*3 or A44*4 side turn signal light socket and wire LH connector.
Disconnect the T7*1 or T5*1, or T17*2 rear combination light socket and wire sub-assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L50-6 (LL) - A3-2 (B) | Always | Below 1 Ω |
| L50-6 (LL) - A11-2*3 | Always | Below 1 Ω |
| L50-6 (LL) - A44-2*4 | Always | Below 1 Ω |
| L50-6 (LL) - T7-3 (TRN)*1 | Always | Below 1 Ω |
| L50-6 (LL) - T5-2 (TRN)*1 | Always | Below 1 Ω |
| L50-6 (LL) - T17-3 (TRN)*2 | Always | Below 1 Ω |
| A3-1 (E) - Body ground | Always | Below 1 Ω |
| A11-1 - Body ground*3 | Always | Below 1 Ω |
| A44-1 - Body ground*4 | Always | Below 1 Ω |
| T7-1 (TE) - Body ground*1 | Always | Below 1 Ω |
| T5-5 (E) - Body ground*1 | Always | Below 1 Ω |
| T17-2 (E) - Body ground*2 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front turn signal light socket LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY
Apply battery voltage to the connector and check the light illumination condition.
| Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 2 (B) Battery negative (-) → Terminal 1 (E) |
Turn signal light illuminates |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the side turn signal light socket and wire LH.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>DISASSEMBLY
Apply battery voltage to the connector and check the light illumination condition.
| Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 2 Battery negative (-) → Terminal 1 |
Turn signal light illuminates |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear combination light socket and wire sub-assembly LH.
for Canvas Top: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Canvas Top)>DISASSEMBLY
for Pickup: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Pickup)>DISASSEMBLY
for Van: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Van)>DISASSEMBLY
Apply battery voltage to the connector and check the light illumination condition.
| Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 3 (TRN)*1 Battery negative (-) → Terminal 1 (TE)*1 |
Turn signal light illuminates |
| Battery positive (+) → Terminal 2 (TRN)*2 Battery negative (-) → Terminal 5 (E)*2 |
Turn signal light illuminates |
| Battery positive (+) → Terminal 3 (TRN)*3 Battery negative (-) → Terminal 2 (E)*3 |
Turn signal light illuminates |
*1: for T7 connector
*2: for T5 connector
*3: for T17 connector
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Canvas Top: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Canvas Top)>DISASSEMBLY
for Pickup: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Pickup)>DISASSEMBLY
for Van: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Van)>DISASSEMBLY
*1: except Pickup
*2: for Pickup
*3: for Small Type
*4: for Large Type
Disconnect the L50 combination meter assembly connector.
Disconnect the I38 front turn signal light socket RH connector.
Disconnect the I25*3 or I129*4 side turn signal light socket and wire RH connector.
Disconnect the T6*1 or T1*1, or T14*2 rear combination light socket and wire sub-assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L50-4 (LR) - I38-2 (B) | Always | Below 1 Ω |
| L50-4 (LR) - I25-2*3 | Always | Below 1 Ω |
| L50-4 (LR) - I129-2*4 | Always | Below 1 Ω |
| L50-4 (LR) - T6-3 (TRN)*1 | Always | Below 1 Ω |
| L50-4 (LR) - T1-2 (TRN)*1 | Always | Below 1 Ω |
| L50-4 (LR) - T14-3 (TRN)*2 | Always | Below 1 Ω |
| I38-1 (E) - Body ground | Always | Below 1 Ω |
| I25-1 - Body ground*3 | Always | Below 1 Ω |
| I129-1 - Body ground*4 | Always | Below 1 Ω |
| T6-1 (TE) - Body ground*1 | Always | Below 1 Ω |
| T1-5 (E) - Body ground*1 | Always | Below 1 Ω |
| T14-2 (E) - Body ground*2 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front turn signal light socket RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY
Apply battery voltage to the connector and check the light illumination condition.
| Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 2 (B) Battery negative (-) → Terminal 1 (E) |
Turn signal light illuminates |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the side turn signal light socket and wire RH.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>DISASSEMBLY
Apply battery voltage to the connector and check the light illumination condition.
| Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 2 Battery negative (-) → Terminal 1 |
Turn signal light illuminates |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear combination light socket and wire sub-assembly RH.
for Canvas Top: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Canvas Top)>DISASSEMBLY
for Pickup: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Pickup)>DISASSEMBLY
for Van: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Van)>DISASSEMBLY
Apply battery voltage to the connector and check the light illumination condition.
| Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 3 (TRN)*1 Battery negative (-) → Terminal 1 (TE)*1 |
Turn signal light illuminates |
| Battery positive (+) → Terminal 2 (TRN)*2 Battery negative (-) → Terminal 5 (E)*2 |
Turn signal light illuminates |
| Battery positive (+) → Terminal 3 (TRN)*3 Battery negative (-) → Terminal 2 (E)*3 |
Turn signal light illuminates |
*1: for T6 connector
*2: for T1 connector
*3: for T14 connector
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Canvas Top: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Canvas Top)>DISASSEMBLY
for Pickup: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Pickup)>DISASSEMBLY
for Van: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Van)>DISASSEMBLY
Check the illumination of each turn signal light.
| Result | Proceed to |
|---|---|
| LH side turn signal light does not illuminate. | A |
| RH side turn signal light does not illuminate. | B |
A
B
*1: except Pickup
*2: for Pickup
*3: for Small Type
*4: for Large Type
Disconnect the L50 combination meter assembly connector.
Disconnect the A3 front turn signal light socket LH connector.
Disconnect the A11*3 or A44*4 side turn signal light socket and wire LH connector.
Disconnect the T7*1 or T5*1, or T17*2 rear combination light socket and wire sub-assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L50-6 (LL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A3 front turn signal light socket LH connector.
Clear the DTCs.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Turn on the turn signal light LH and check that DTCs are output.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| B1508 is output | A |
| B1507 is output | B |
A
B
Disconnect the A11*1 or A44*2 side turn signal light socket and wire LH connector.
*1: for Small Type
*2: for Large Type
Clear the DTCs.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Turn on the turn signal light LH and check that DTCs are output.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| B1508 is output | A |
| B1507 is output | B |
A
B
*1: except Pickup
*2: for Pickup
Disconnect the T7*1 or T5*1, or T17*2 rear combination light socket and wire sub-assembly LH connector.
Clear the DTCs.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Turn on the turn signal light LH and check that DTCs are output.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| B1508 is output | A |
| B1507 is output | B |
A
B
for Canvas Top: Click here
for Pickup: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Pickup)>DISASSEMBLY
for Van: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Van)>DISASSEMBLY
*1: except Pickup
*2: for Pickup
*3: for Small Type
*4: for Large Type
Disconnect the L50 combination meter assembly connector.
Disconnect the I38 front turn signal light socket RH connector.
Disconnect the I25*3 or I129*4 side turn signal light socket and wire RH connector.
Disconnect the T6*1 or T1*1, or T14*2 rear combination light socket and wire sub-assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L50-4 (LR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I38 front turn signal light socket RH connector.
Clear the DTCs.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Turn on the turn signal light RH and check that DTCs are output.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| B1508 is output | A |
| B1507 is output | B |
A
B
Disconnect the I25*1 or I129*2 side turn signal light socket and wire RH connector.
*1: for Small Type
*2: for Large Type
Clear the DTCs.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Turn on the turn signal light RH and check that DTCs are output.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| B1508 is output | A |
| B1507 is output | B |
A
B
*1: except Pickup
*2: for Pickup
Disconnect the T6*1 or T1*1, or T14*2 rear combination light socket and wire sub-assembly LH connector.
Clear the DTCs.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Turn on the turn signal light RH and check that DTCs are output.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| B1508 is output | A |
| B1507 is output | B |
A
B
for Canvas Top: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Canvas Top)>DISASSEMBLY
for Pickup: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Pickup)>DISASSEMBLY
for Van: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Van)>DISASSEMBLY